Skip navigation
Go to Global Navigation
Go to Primary Contents
Go to Site Information

Yokogawa Corporation of America

Worldwide Locations

North & Central America

General Specifications

Below are 927 results from your search.

1.0 MB

237700 Conducell 4US-G125

81 KB

237750 Conducell 4US-T150

257 KB
Edition 1

375 Field Communicator (GS HT375-01E-A)

Yokogawa is pleased to offer the 375 Field Communicator--Building on experience with the proven 275 HART Communicator, the 375 Field Communicator is designed to support all devices using HART® or FOUNDATION™ fieldbus digital communication protocols. The 375 Field Communicator enables users to configure and maintain all of their instruments and valves--in the field or on the bench--with one intrinsically safe handheld device.

240 KB

415920, 415921 and 415922 Shunt Resistor for Screw Input Terminal (GS 04P01A01-91EN)

415920, 415921 and 415922 are precision shunt resistors, to convert DC current signal to DC voltage.

240 KB
Edition 2

Access Control and Operation History Management Package (GS 32Q04D30-31E)

Access Control and Operation History Management Package is used to set the operation rights of engineers who operate the safety engineering PC (SENG), as well as to record the operation history. This package is divided into the Access Control function and Operation History Management function.

395 KB
Edition 3

Advanced Reflux Sampler - YARS100 GS (GS 11A00V01-01E-A)

The Advanced Reflux Sampler is a self contained two stage system designed to provide simple, fast and highly accurate sample conditioning analysis for severe process applications.

427 KB
Edition 19

Analog I/O Modules (GS 34P02Q31-01E)

This GS covers the hardware specifications of analog input/output modules that can be installed in an FCN autonomous controller. For connection with field equipment, refer to GS 34P02Q30-01E "Field Connection Specifications" and TI 34P02Q91-01E "FCN/FCJ Installation Guide."

460 KB
Edition 5

Analog I/O Modules (for ProSafe-RS) (GS 32Q06K30-31E)

This GS describes the hardware specifications of the analog I/O modules that can be mounted on the safety node unit (SNB10D) and the safety control unit (SSC60, SSC50 or SSC10).

386 KB
Edition 19

Application Portfolios for FCN/FCJ (GS34P02P20-01E)

The Application Portfolios for FCN/FCJ are series of
engineering parts to be used on Logic Designer, which
is the FCN/FCJ's engineering tool.

33 KB

Applications Consultation

3.7 MB
Edition 3

AR Series (GS 77M02A01-01EN)

This high quality arrester protects electronic instruments by absorbing induced lightning surge voltage. Arrester (SPD) should be set between lines through which surges are entered and serves to protect instruments such as transmitters or receivers safely from thunder inducement.

65 KB
Edition 2

AR-HA Arrester for Current Signal (GS AR02-01E)

This high quality arrester protects electronic Instruments by absorbing induced lightning surge voltage Arrester should be set between lines through which surges are entered and serves to protect instruments such as transmitters or receivers safely from thunder inducement.

56 KB
Edition 2

AR-PL Arrester for Large Capacity Power Supply (GS AR34-01E)

This high quality arrester protects electronic instruments by absorbing induced lightning surge voltage. Compact type arrester with large capacity consisting of high quality ceramic type arrester and varister. 

66 KB
Edition 2

AR-PW Arrester for Power Supply (GS AR33-01E)

This high quality arrester protects electronic instruments by absorbing induced lightning surge voltage. Input signal is 100V AC. Load current capacity is 20A. With LED indicator. 

69 KB
Edition 1

AR-SY Arrester for Selsyn (GS-AR08-01E)

This high quality arrester protects electronic instruments by absorbing induced lightning surge voltage. Arrester should be set between lines through which surge enters and serves to protect instruments such as transmitters or receivers safely from thunder inducement.

73 KB
Edition 1

AR1-B2 Arrester for Communication Line (GS AR21-01E)

This high quality arrester protects communication equipment from lighting surges induced in communication line. Applicable to communication lines having frequency range of DC∼20kHz and voltage range of 0∼24V DC. Screw terminal connection makes easy relay to communication lines. No affect for communication lines even if main body is removed.

72 KB
Edition 1

AR1-D6 Arrester for Communication Line (GS AR22-01E)

This high quality arrester protects communication equipment from lighting surges induced in communication line. Applicable to communication lines having frequency range of DC∼2mHz and voltage range of 0∼150V DC. Screw terminal connection makes easy relay to communication lines. No affect for communication lines even if main body is removed.

225 KB
Edition 5

Auxiliary Modules - AC-534-00 - Line Monitoring Module (24 Vdc outputs, 2.5–20 W) (GS 48C34Z00-00E-N)

This alarming line monitoring module has 4 channels for line monitoring of a 24 Vdc output with 2.5 - 20 W load. This alarming line current monitoring module has 4 channels. Each channel can be used for line monitoring of a 24 Vdc output with 2.5 - 20 W load.

202 KB
Edition 5

Auxiliary Modules - AC-534-A0 - Line Monitoring Module (110 Vdc outputs) (GS 48C34A00-00E-N)

This alarming line monitoring module has 4 channels for line monitoring of a 110 Vdc output with 5 - 20 W load. This alarming line current monitoring module has 4 channels. Each channel can be used for line monitoring of a 110 Vdc output with 5 - 20 W load.

208 KB
Edition 4

Auxiliary Modules - AC-534-B0 - Line Monitoring Module (24 Vdc inputs) (GS 48C34B00-00E-N)

This alarming line monitoring module has 4 channels for line monitoring of a 24 Vdc DI-511 input.) This alarming line current monitoring module has 4 channels. Each channel can be used for line monitoring of a 24 Vdc input in combination with a DI -511-vr module.

213 KB
Edition 5

Auxiliary Modules - AC-534-C0 - Line Monitoring Module (24 Vdc outputs, 0.2–20 W) (GS 48C34C00-00E-N)

This alarming line monitoring module has 4 channels for line monitoring of a 24 Vdc output with low test current (0.2 - 20 W load). This alarming line current monitoring module has 4 channels. Each channel can be used for line monitoring of a 24 Vdc output with low test current (0.2 - 20 W load).

224 KB
Edition 1

Auxiliary Modules - AC-534-D0 - Line Monitoring Module (24 Vdc inputs with zener barriers) (GS 48C34D00-00E-N)

This alarming line monitoring module has 4 channels for line monitoring of a 24 Vdc input with zener barrier and DI-511-A This alarming line current monitoring module has 4 channels. Each channel can be used for line monitoring of a 24 Vdc input in combination with a zener barrier and DI-511-A module.

229 KB
Edition 3

Auxiliary Modules - AC-534-E0 - Line Monitoring Module (24 Vdc outputs, 1–10 W) (GS 48C34E00-00E-N)

This alarming line monitoring module has 4 channels for line monitoring of a 24 Vdc output with 1 - 10 W load. This alarming line current monitoring module has 4  channels. Each channel can be used for line monitoring of a 24 Vdc output with 1 - 10 W load.

215 KB
Edition 4

Auxiliary Modules - AC-535-00 - Line Monitoring Module (normally de-energized inputs) (GS 48C35Z00-00E-N)

This module has four monitoring circuits for fail-safe 24 Vdc inputs. The input connections are guarded against interruption and short-circuiting, each circuit having a front indication. The logic input will be disabled in case of a line short. This function can be disabled per channel. In this case the module acts as an AC-534-B.

172 KB
Edition 4

Auxiliary Modules - AF-533-A3 - Fuse Module (400 mA fast) (GS 48C33A03-00E-N)

Alarming fuse module with indication for general purpose. This alarming fuse module has 6 channels. Each channel has a front accessible fuse with LED indication. The module is also provided with a common annunciating contact and a common dc current sink output. The channels are galvanically isolated.

172 KB
Edition 2

Auxiliary Modules - AF-533-B3 - Fuse Module (50 mA medium slow) (GS 48C33B03-00E-N)

Alarming fuse module with indication for general purpose. This alarming fuse module has 6 channels. Each channel has a front accessible fuse with LED indication. The module is also provided with a common annunciating contact and a common dc current sink output. The channels are galvanically isolated.

365 KB
Edition 4

Auxiliary Modules - AO-543-01 - Annunciator Module (GS 48C43Z01-00E-N)

This module has two independent annunciator circuits. The circuits handle fault signals and operator actions (acknowledge, reset, etc.). Each circuit is connected to one indication light. Common outputs like an audible alarm are possible in combination with the KA-549 module.

178 KB
Edition 3

Auxiliary Modules - DR-546-01 - Multi Purpose Module (GS 48C46Z01-00E-N)

The multi purpose module can be used for auxiliary circuits. The module has a number of typical characteristics:

  • Free assembly for twenty circuits with up to four components each,
  • Suitable for mounting diodes, resistors or capacitors.
162 KB
Edition 4

Auxiliary Modules - DR-546-C1 - Multi Purpose Diode Module (GS 48C46C01-00E-N)

This multi purpose diode module has 20 channels. Each channel consists of a single diode. The module is mainly used as coupling / decoupling module for dc signals or power supplies.

173 KB
Edition 3

Auxiliary Modules - DR-546-F1 - Analogue Signal Filtering Module (GS 48C46F01-00E-N)

The analog signal filtering module has 8 circuits. Each channel has a large capacitor intended for smoothing analogue input signals (0 20 mA). The capacitors are protected by a parallel connected zener diode. Each channel is provided with a serial connected resistor to supply unused analogue inputs with a small current to prevent line failure situations.

160 KB
Edition 3

Auxiliary Modules - DR-546-G1 - Smart Transmitter Resistor Module (GS 48C46G01-00E-N)

The module is used as a resistor module for loop impedance correction when using smart transmitters. Smart transmitters based on the Hart protocol need extra impedance in the loop in order to make it possible to use a hand held communicator.

148 KB
Edition 4

Auxiliary Modules - FD-509-00 - Decoupling Module (GS 48C09Z00-00E-N)

This module is used for decoupling of fail-safe and non fail-safe modules. The module contains ten decoupling circuits. Each circuit has a current pulse input and output.

207 KB
Edition 3

Auxiliary Modules - KA-549-00 - Annunciator Auxiliary Module (GS 48C49Z00-00E-N)

This module has a horn driver circuit, two reflash circuits, and a flash generator circuit. The module can be used in combination with AO-543 modules.

214 KB
Edition 4

Auxiliary Modules - SA-539-00 - System Alarm Module (GS 48C39Z00-00E-N)

This System Alarm module provides centralized fault detection and signaling via alarm light and relay. Eight categories of faults are distinguished, in cluding power supplies, clocks/timers, fuses, circuit
breakers, etc.

185 KB
Edition 1

Auxiliary Modules - SC-592-01 - Switch Module (GS 48C92Z01-00E-N)

This multi purpose switch module has six channels. The module has six switches with locked lever and LED indication per channel. Channels are galvanically separated.

174 KB
Edition 4

Auxiliary Modules AF-533-03 Fuse Module (2 A fast) (GS 48C33Z03-00E-N)

Alarming fuse module with indication for general purpose. This alarming fuse module has 6 channels. Each channel has a front accessible fuse with LED indication. The module is also provided with a common annunciating contact and a common dc current sink output. The channels are galvanically isolated.

1.3 MB
Edition 6

AV550G and ZR22G GS Sheets 6th Edition (GS 11M12D01-01E)

Zirconia oxygen analyzers are used in various combustion facilities to measure flue gas oxygen concentration, through which optimum combustion efficiency can be achieved. This reduces energy consumption, saves on fuel costs, and decreases atmospheric emissions.

1.4 MB
Edition 15

AXF Magnetic Flow Meter Integral Flow Meter /Remote Flowtube (GS 01E20D01-01E) NEW

The AXF magnetic flow meter series are sophisticated products with outstanding reliability and ease of operation, developed on the basis of decades of field-proven experience. The combination of a replaceable electrode and the diagnostic to defect adhesion level on the electrodes dramatically improves maintainability.

119 KB
Edition 2

AXF PROFIBUS PA Communication Type Magnetic Flow Meter (GS 01E20F12-01E)

PROFIBUS is a vendor-independent and open fieldbus based on the international standard IEC61158 and IEC61784. It covers a wide range of applications in manufacturing and process automation fields. Vendor-independence and openness allow communication between devices of different manufactures with no special interface adjustment.

114 KB
Edition 2

AXF Series Foundation Fieldbus Communcation Type General Specification (GS 01E20F02-01E)

FOUNDATION Fieldbus is the digital communication line for the field instruments, whose signal is internationally standardized by Fieldbus Foundation. The Fieldbus bi-directional digital communication performance makes possible for the field instruments and the control devices to be a complete on-line system, superseding the existing analog transmission lines.

292 KB
Edition 5

AXFA11 Magnetic Converter for Remote Flowtube (GS 01E20C01-02E-A)

The AXFA11 magnetic converter has been developed based on Yokogawa's decades long experience in magnetic flowmeters. The AXFA11 continues the tradition of high quality and reliability that has become synonymous with the Yokogawa name and in addition features an even higher level of performance and increased functionality.

247 KB
Edition 10

AXFA11G Magnetic Flow Meter Remote Converter (GS 01E20C01-01E)

The AXFA11 magnetic flow meter high grade remote converter is a sophisticated product with outstanding reliability and ease of operation, developed on the basis of decades of field-proven experience. The AXFA11 employs an LCD indicator, infra-red switches, and "Easy Setup" parameters to ensure substantially improved ease of maintenance.

175 KB
Edition 12

AXFA14G Magnetic Remote Converter (GS 01E20C02-01E)

The AXFA14 magnetic flow meter remote converter is a sophisticated product with outstanding reliability and ease of operation, developed on the basis of decades of field-proven experience. The AXFA14 employs an LCD indicator, infra-red switches, and "Easy Setup" parameters to ensure substantially improved ease of maintenance.

3.1 MB
Edition 3

AXR Two-wire Magnetic Flow Meter Integral Flow Meter (GS 01E30D01-01EN)

The ADMAG AXR two-wire magnetic flowmeter can be installed in the two-wire system without any AC power source, thus drastically reducing the initial instrumentation cost. The ADMAG AXR is the world's first two-wire magnetic flowmeter which employs the fluid noise free "Dual Frequency Excitation Method," achieving excellent stability for instrumentation.

1.2 MB
Edition 3

AXW Magnetic Flow Meter Remote Flowtube (GS 01E25D11-01EN)

The ADMAG AXW series of magnetic flow meters has been developed based on Yokogawa's decades long experience in Magnetic Flowmeters. The AXW series continues the tradition of high quality and reliability that has become synonymous with the Yokogawa name. The AXW series is ideal for industrial process lines, and water supply / sewage applications.

675 KB
Edition 1

Batch Controller Model 414 (BU 01P11A03-E-U)

The 414 Batch Controller is suited to flow applications where precise measurement and control of batch quantities is required. Batch total, flow rate, accumulated total and preset value can all be displayed in
engineering units on the large LCD display. The 414 will interface to  most flow meters with versions available for pulse and analog inputs.

580 KB
Edition 2

Beta-ray Sensor (GS 14M04C10-20E-Z1)

The Beta-ray sensor is a sensor that uses a transmission method and provides highly accurate and stable measurement. The radiation source of this sensor is Kr (krypton). In order to minimize the influence of the disturbance, the sensor contains temperature compensation, air purging and other unique features based on 30 years field experience.

182 KB
Edition 4

BT200 Brain Terminal (GS 01C00A11-00E)

As a portable terminal, the Model BT200 BRAIN TERMINAL is used in combination with equipment using brain communication for setting, changing, displaying and printing out parameters such as tag number, output mode, and range, through simultaneous communication. It also monitors I/O values and self-check results, sets constant-current output, and allows zero adjustments.

440 KB
Edition 4

Cables (for ProSafe-RS) (GS 32Q06M10-31E)

This GS covers the specifications for cables used in the ProSafe-RS system.

3.3 MB
Edition 2

CANopen Communication Module (GS 34P02Q58-01E)

This General Specification (GS) describes CANopen communication functions and hardware specifications of the module. The CANopen Communication Module is installed in the FCN or FCN-RTU and communicates with the devices that have CANopen communication functionality. 

163 KB
182 KB
Edition 1

CENTUM VP/CS 3000 Integration Engineering Package (GS 32Q04D10-31E)

The CHS5200 CENTUM VP/CS 3000 Integration Engineering Package runs on a safety engineering PC (SENG) to integrate ProSafe-RS and the CENTUM VP/CENTUM CS 3000 (hereinafter called the VP/CS 3000).

232 KB
Edition 11

Cleaning Assembly (GS 12B6V1-E-E)

For industrial applications and particularly for automatic process measurements it is of the greatest importance that the sensitive part of a glass electrode and the diaphragm of a reference electrode are kept clean. Often it is not practical to interrupt a process for cleaning the electrodes, an accurate indication is required over a long period, replacing the electrodes is difficult, etc.

1.1 MB
Edition 4

Compact O Frame (GS 14M04B10-20E-Z1)

The WG41F11C Compact O frame is a space-saving frame designed for coating lines of battery electrode sheets. This space-saving frame performs high-speed scanning by using our unique drive mechanism to precisely measure the quality of high value-added sheets. This frame consists of its main body, a linear servo drive system, a frame processor, and a sensor head package.

72 KB
Edition 3

Computing & Report Function and Fixed-time File Function for DC100 Data Collector —"/M3" Option (GS 04M01J01-31E)

These functions create statistical information files and save them in the DC100's internal memory. There are two types of statistical information files: report files (hourly-, daily- or monthly-report files) and fixed-time files (measured-value files created on an hourly, daily or monthly basis). (Note that both of these functions cannot run at the same time.)

728 KB
Edition 2

Computing Unit  (GS 11B03S02-02E)

The GC1000 MarkII process gas chromatograph unit features PC communication, analog hold output, digital I/O, and communication with a supervisory computer. For analog hold output from the GC1000 MarkII, many signal lines should be installed between the field and instrument room.

1.5 MB
Edition 3

Conductivity PR10 Retractable Assembly for SC4A Sensor (GS 12D7J4-02E-E)

On-line measurements often present extra challenges, especially when routine maintenance is required. The PR10 is ideally suitable for applications where the sensors must be removed without interrupting or shutting down the process. Without any special tools the PR10 can be retracted safely from the process at pressures up to 5 bar.

3.2 MB

Conductivity Sensors

HAMILTON manufactures more than pH sensors. Our electrochemical and optical sensors are reliable tools for application-oriented use and are characterized by high quality, long life and competitive pricing. In order to meet these rigorous requirements we are constantly striving to find unique sensor designs.

956 KB
Edition 2

Coplanar™ Adapter: AK-901 for Differential Pressure Manifolds (GS 22B01C55-01EN-A)

The PGI AK-901 Coplanar™ adapter is designed for use with an existing Integral manifold. The AK-901 provides the end user the capability to mount a traditional 2-1/8" center to center Yokogawa transmitter without replacing the existing manifold. This adapter allows for easy retrofitting of transmitters in the field. Existing mounting brackets and impulse piping can be used as well as wiring and power supply.

42 KB

Corrective Maintenance Service

85 KB
Edition 10

CPU Port Cable (GS 34M06C91-01E)

The FA-M3 CPU Port Cables are used to connect CPU modules such as sequence CPU modules to personal computers, displays and other external devices. The CPU modules are connected via a programming tool interface connector (labeled "PROGRAMMER").

64 KB

csTUNER General Specifications (GS 33B90A01-01E-A)

Yokogawa csTUNER collects live process data and models the dynamics of a process to tune it for improved performance. Tuning constants are calculated by csTUNER and can be downloaded directly the the controller. csTUNER employs a patent-pending process modeling routine that enables users to accurately model non-steady state process data.

151 KB

DA100

1.2 MB
Edition 4

DAQManager Data Management Software for Paperless Recorders (GS 04L47B01-01EN)

DAQManager is a software program that enables you to manage measured data from Daqstation and MVAdvanced paperless recorders on a PC. Data loaded onto DAQManager can be quickly and easily searched by date/time, tag name, batch name, and other criteria. Channels recorded on different instruments and at different intervals can be displayed in the same trend graph or digital display.

28 KB
Edition 3

DAQOPC for DARWIN/OPC Server for DARWIN Series (GS 04M01F03-00E)

In the process industry, there are a variety of data sources in plant devices and databases in the control room. However, until now, it was not necessarily easy to access operation data on the plant devices from supervisory information systems.

72 KB
Edition 5

DAQOPC OPC Server for Daqstation/MobileCorder (GS 04L01B03-00E)

DAQOPC is an OPC (OLE for Process Control) server running on Windows 2000/XP, which can be connected to the DAQSTATION DX/DX-P/CX series, MobileCorder MV series and provides an OPC client with process data via OPC interface. With the package, the OPC client can acquire and define process data from and receive alarm events. 

320 KB
Edition 9

Daqstation CX1000 Control and Measurement Station (GS 04L31A01-01E)

CX1000 is a controller with up to 6 ch measurement channels and up to 2 embedded loops. By using Ethernet interface equipped as standard feature, it is possible to send e-mails, monitor the site remotely on the Web, and make an FTP-based file transfer. CX1000 comes standard with control and measurement screens; CX1000 operation screen can be used with program-less.
416 KB
Edition 9

Daqstation CX2000 Control and Measurement Station (GS 04L31A01-02E)

CX2000 is a controller with up to 20 ch measurement channels and up to 6 embedded loops. By using Ethernet interface equipped as standard feature, it is possible to send e-mails, monitor the site remotely on the Web, and make an FTP-based file transfer. CX2000 comes standard with control and measurement screens; CX2000 operation screen can be used with program-less.

522 KB
Edition 6

DAQSTATION DX100 (GS 04L01A01-00E)

The DX100 is a DAQSTATION that displays real-time measured data on a color LCD and saves data on a 3.5- inch floppy disk, PCMCIA ATA flash memory card or Zip disk. It can be hooked up to network via Ethernet, which enables to inform by E-mail and to monitor on Web site as well as to transfer files by using FTP. Also, it can communicate with FOUNDATION™ Fieldbus and Modbus.

763 KB
Edition 16

Daqstation DX1000 (GS 04L41B01-01E) NEW

The DX1000 is a DAQSTATION that displays real-time measured data on a color LCD and saves data on a CompactFlash memory card (CF card). It can be hooked up to network via Ethernet, which enables to inform by E-mail and to monitor on Web site as well as to transfer files by using FTP. Also, it can communicate with Modbus/RTU or Modbus/TCP.

636 KB
Edition 15

Daqstation DX1000N (GS 04L43B01-01E) NEW

The DX1000N is a inner chassis removable model. This provides access to all of the internal components of the DX1000N from the front panel. It can be hooked up to network via Ethernet, which enables to inform by E-mail and to monitor on Web site as well as to transfer files by using FTP. Also, it can communicate with Modbus/RTU or Modbus/TCP.

763 KB
Edition 6

Daqstation DX1000T (GS 04L45B01-01EN) NEW

The DX1000T is a Daqstation that displays real-time measured data on a color LCD and saves data on a CompactFlash memory card (CF card). It can be hooked up to network via Ethernet, which enables to inform by E-mail and to monitor on Web site as well as to transfer files by using FTP. Also, it can communicate with Modbus/RTU or Modbus/TCP.
418 KB
Edition 5

DAQSTATION DX100L Special Housing Model (GS 04L04A01-00E)

he DX100L was developed as a replacement for recorders with different panel cut dimensions, or depth dimensions, such as the Foxboro (SPE200), SRHD, NRE, or μR100F. The DX100L is a DAQSTATION that displays real-time measured data on a color LCD and saves data on a 3.5- inch floppy disk, PCMCIA ATA flash memory card or Zip disk.

431 KB
Edition 8

DAQSTATION DX100P (GS 04L05A01-00E)

The DX100P is a DAQSTATION that can display measurement data on a color LCD screen in real-time, and store them to a compact flash memory card. It can be connected to Ethernet, Modbus, and other networks. A standard Ethernet port allows such network capabilities as sending messages by e-mail, remote monitoring through a Web browser, and file transfer with FTP, and time adjustment by SNTP.

705 KB
Edition 7

DAQSTATION DX200 (GS 04L02A01-00E)

The DX200 is a DAQSTATION that displays real-time measured data on a color LCD and saves data on a 3.5- inch floppy disk. It can be hooked up to network via Ethernet, which enables to inform by E-mail and to monitor on Web site as well as to transfer files by using FTP. Also, it can communicate with FOUNDATIONTM Fieldbus and Modbus.

1.1 MB
Edition 14

DAQSTATION DX2000 (GS 04L42B01-01E) NEW

The DX2000 is a DAQSTATION that displays real-time measured data on a color LCD and saves data on a CompactFlash memory card (CF card). It can be hooked up to network via Ethernet, which enables to inform by E-mail and to monitor on Web site as well as to transfer files by using FTP. Also, it can communicate with Modbus/RTU or Modbus/TCP.
1.1 MB
Edition 5

Daqstation DX2000T (GS 04L45B02-01EN) NEW

The DX2000T is a Daqstation that displays real-time measured data on a color LCD and saves data on a CompactFlash memory card (CF card). It can be hooked up to network via Ethernet, which enables to inform by E-mail and to monitor on Web site as well as to transfer files by using FTP. Also, it can communicate with Modbus/RTU or Modbus/TCP.

524 KB
Edition 5

DAQSTATION DX200C (GS 04L03A01-00E)

The DX200C is a DAQSTATION that displays real-time measured data on a color LCD and saves data on a 3.5- inch floppy disk, PCMCIA ATA flash memory card or Zip disk. It can be hooked up to network via Ethernet, which enables to inform by E-mail and to monitor on Web site as well as to transfer files by using FTP. Also, it can communicate with FOUNDATION™ Fieldbus and Modbus.

720 KB
Edition 9

DAQSTATION DX200P (GS 04L06A01-00E)

The DX200P is a DAQSTATION that can display measurement data on a color LCD screen in real-time, and store them to a compact flash memory card. It can be connected to Ethernet, Modbus, and other networks. A standard Ethernet port allows such network capabilities as sending messages by e-mail, remote monitoring through a Web browser, and file transfer with FTP, and time adjustment by SNTP.

130 KB
Edition 1

DAQSTATION Pharmaceutical model DX100P/DX200P Easy Text Entry (Remote Control) option (GS 04L05A01-01E)

A new wireless remote control option greatly simplifies text entry operations on DX100P/DX200P models. Control and setting parameters can now be input by remote control! Controlled system access to DX100P/DX200P is attained via user log in functions. These operations, plus message, batch, and electronic signature text entry can now be simplified with the new remote control option.

36 KB

DAQWORX Hardware Compatibility (ns-daqworx-compati)

73 KB
Edition 1

DARWIN Data Acquisition Instrument Modbus Interface Module (GS 4M1E1-91E)

The DT300-31/S6 Modbus Interface module enables DARWIN hardware to be used with any Modbus RTU host device. Two unlike devices that support Modbus protocol can be linked together and exchange data. Using the Modbus Interface Module, DARWIN I/O can be used as a low cost alternative for adding inputs or outputs to an existing DCS or PLC.

158 KB
Edition 11

Data Acquisition Software Suite DAQWORX (GS 04L00L00-00E)

DAQWORX was created as a no-programming software package that forms the basis for a data acquisition system when combined with a variety of instruments including recorders, data acquisition instruments, and other types of measuring instruments. In terms of adding functionality, DAQWORX is designed as what we call data acquisition integrated software, allowing customers to connect high added value software to their existing data acquisition systems to easily expand the range of supported applications.

1.0 MB
Edition 13

Data Acquisition Unit DA100 Sub units DS400/DS600 (GS 04M01B01-11E)

DARWIN is a system comprising a number of data-acquisition equipment components. In the course of system growth, new models, software, various input/output modules and optional features are added to the family to enhance the systems expandability and flexibility.
1.3 MB
Edition 1

Data Acquisition Unit MW100 (GS 04M10B01-01E)

The MW100 is a powerful general-purpose data acquisition instrument. Whether as a standalone or connected to a PC, the MW100 offers a flexible data acquisition solution. Designed under the concept of "Smart Logging – Anytime, Anyplace," the MW100 offers the following features.

1.1 MB
Edition 7

Data Collector DC100 Main unit (stand-alone type, expandable type), Sub units (DS400/DS600) (GS 04M01J01-11E)

DARWIN is a system comprising a number of data-acquisition equipment components. In the course of system growth, new models, software, various input/output modules and optional features are added to the family to enhance the systems expandability and flexibility.

1.2 MB
Edition 2

Data Logging Software GA10 (GS 04L65B01-01EN)

Data Logging Software GA10 (hereafter referred to as GA10) is used to collect data from measuring instruments and controllers via communication and monitor and record the collected data. GA10 has two setting modes for configuring data collection, monitoring, and recording: Simple Settings mode and Detail Settings mode.

784 KB
Edition 2

Diaphragm Seals use with DPharp family Transmitter (GS SLC21A0-02E-A)

Our remote seal Diaphragm Measurement System is commonly used when process-operating conditions extend beyond the normal operating limits of a pressure transmitter. In addition, they are used to reduce the weight of the device at the process connection, particularly with conventional pressure transmitters. 

539 KB
Edition 14

Digital I/O Modules (GS 34P02Q35-01E)

This GS covers the hardware specifications of digital input/output modules that can be installed in an FCN autonomous controller. For connection with field equipment, refer to GS 34P02Q30-01E "Field Connection Specifications" and TI 34P02Q91-01E "FCN/FCJ Installation Guide."

826 KB
Edition 5

Digital I/O Modules (for ProSafe-RS) (GS 32Q06K40-31E)

This GS provides the hardware specifications of the digital I/O modules that can be installed in the Safety Node Unit (SNB10D) and Safety Control Units (SSC60, SSC50, SSC10).

603 KB
Edition 7

DM8C/VD6 Liquid Denisty Analyzer (GS 12T3A1-E)

In 1967, YOKOGAWA developed the Model VD6 Vibration Type Liquid Density Meter in response to user requests for an online density meter, to assist in process automation and saving labor resources and energy while further improving and stabilizing quality. This was an important development in the instrumentation field, because density is a fundamental physical quantity, the accurate measurement of which is important for almost all processes.

466 KB
Edition 12

DNP3 Communication Portfolio (GS34P02P22-01E)

This General Specifications document describes the Distributed Network Protocol (DNP3) Communication Portfolio for STARDOM. The DNP3 Communication Portfolio generates a control application for FCN/FCJ autonomous controllers. Using this portfolio, the FCN/FCJ can perform DNP3 communication via a serial port or Ethernet port.

71 KB

DR230

748 KB
Edition 13

DR230 Hybrid recorder expandable type DS400/DS600 (GS 04M01C01-12E)

DARWIN is a system comprising a number of data-acquisition equipment components. In the course of system growth, new models, software, various input/output modules and optional features are added to the family to enhance the systems expandability and flexibility. You can check the versions of your equipment and software by referring to the style number: Sn* shown on the nameplate of the main unit.

271 KB
Edition 13

DR230 Hybrid recorder stand-alone type (GS 04M01C01-11E)

DARWIN is a system comprising a number of data-acquisition equipment components. In the course of system growth, new models, software, various input/output modules and optional features are added to the family to enhance the systems expandability and flexibility. You can check the versions of your equipment and software by referring to the style number: Sn* shown on the nameplate of the main unit.

50 KB

DR240

778 KB
Edition 12

DR240 Hybrid recorder expandable type DS400/DS600 (GS 04M01D01-12E)

DARWIN is a system comprising a number of data-acquisition equipment components. In the course of system growth, new models, software, various input/output modules and optional features are added to the family to enhance the systems expandability and flexibility. You can check the versions of your equipment and software by referring to the style number: Sn* shown on the nameplate of the main unit.

275 KB
Edition 14

DR240 Hybrid recorder stand-alone type (GS 04M01D01-11E)

DARWIN is a system comprising a number of data-acquisition equipment components. In the course of system growth, new models, software, various input/output modules and optional features are added to the family to enhance the systems expandability and flexibility. You can check the versions of your equipment and software by referring to the style number: Sn* shown on the nameplate of the main unit.

52 KB
Edition 3

DT500 Retransmission Modules (GS 04M01E01-50E)

DARWIN is a system comprising a number of data-acquisition equipment components. In the course of system growth, new models, software, various input/output modules, and optional features are added to the family to enhance the systems expandability and flexibility. You can check the versions of your equipment by referring to the style number shown on the nameplate of the main unit, and software package, by referring to its release number.

173 KB
Edition 2

Duplexed Network Program for FCN/FCJ OPC Server (GS 34P02Q62-01E)

The Duplexed Network Program for FCN/FCJ OPC Server is a program for duplexing network communication between a PC and FCN/FCJ (field control node/field control junction). Use of this program allows you to conduct communications without being aware of the duplexed network, using general-purpose network devices.

292 KB
Edition 4

Dust Monitor DT450G (GS 11K01C01-01E)

Powder is used in many industries including ceramics,cement, chemicals, pharmaceutical and food. In their processes, powder is collected in order to reduce the loss incurred in the process. Dust emissions from industrial plants are limited by the air pollution control law, local regulations or other guidelines. Each industrial facility is required to be maintained so that its dust emissions do not exceed the allowable level.

43 KB
Edition 1

DX100, DX200 /S120 Enhancement Option (GS 04L01A01-S120E)

DX100, DX200 /S120 option provides numerous functional enhancements for these models. Specify /S120 in the option code for these models to order this option.

63 KB
Edition 1

DX200 /S123 Expandable Input Option (GS 04L02A01-S123E)

The DX200 /S123 expandable input option supports up to 200 additional input channels from external hardware that can be used in conjunction with built in measurement channels, for a total of up to 230 channels. Specify /S123 in the option code of DX210, DX220, or DX230 models to order.

29 KB

EASYFERM Food Data Sheet

The EASYFERM FOOD VP sensors are designed for applications in pharmaceutical industry, biotechnology and food and beverages industry. The FOODLYTE reference electrolyte is intended and foreseen to get into contact with food. It does not harm microorganisms in fermenters.

2.1 MB

EEMUA 191 and ANSI/ISA-18.2-2009 Based Alarm Reporting and Analysis Package (GS GMSCD0601-01E)

Operators of Production Plants are often faced with a large number of alarms and abnormal events that cannot be handled quickly or in the proper sequence due to operator overload. This may result in serious problems such as safety related incidents, shutdowns, production slowdowns or quality issues. In some facilities, the number of alarms is so excessive that operators simply ignore them which can result in disastrous consequences.

211 KB
Edition 32

EJA115 Low Flow Transmitter (GS 01C22K01-00E)

The model EJA115 Low Flow Transmitter is a flow meter comprised of a differential pressure transmitter with an integral orifice and excellent for very low flow measurement. It outputs a 4 to 20 mA DC signal corresponding to the measured flow. The orifice is available in six types with a bore ranging from 0.508 mm to 6.350 mm. 

1.7 MB
Edition 4

EJA118E/Z Diaphragm Sealed Differential Pressure Transmitter (Inner Diaphragm type) (GS 01C31H01-11EN)

Diaphragm seals are used to prevent process medium form entering directly into the pressure-sensing assembly of the differential pressure transmitter, they are connected to the transmitter using capillaries filled with fill fluid. Inner diaphragm type can be installed to small size frange which is 1 inch, 3/4 inch or 1/2 inch. And the performance is the same as 2 inch, because it is used the daiaphragm size same as 2 inch

206 KB
Edition 25

EJA310A Absolute Pressure Transmitter (GS 01C21D01-00E)

The high performance gauge pressure transmitter model EJA310A can be used to measure liquid, gas, or steam pressure. It outputs a 4 to 20 mA DC signal corresponding to the measured absolute pressure. Model EJA310A also features remote setup and monitoring through communications with the BRAIN™ terminal and CENTUM-CS™ or XL™ or HART® 275 host.

201 KB
Edition 27

EJA430A Gauge Pressure Transmitter (GS 01C21E01-00E)

The high performance gauge pressure transmitter model EJA430A can be used to measure liquid, gas, or steam pressure. It outputs a 4 to 20 mA DC signal corresponding to the measured gauge pressure. Model EJA430A also features remote setup and monitoring through communications with the BRAIN™ terminal and CENTUM CS™ or μXL™ or HART® 275 host.

1.6 MB
Edition 4

EJA438E/Z Diaphragm Sealed Gauge Pressure Transmitter (Inner Diaphragm type) (GS 01C31J03-11EN)

Diaphragm seal is used to prevent process medium form entering directly into the pressure-sensing assembly of the pressure transmitter, it is connected to the transmitter using capillary filled with fill fluid. Inner diaphragm type can be installed to small size frange which is 1 inch, 3/4 inch or 1/2 inch.

221 KB
Edition 26

EJA440A High Static Gauge Pressure Transmitter (GS 01C21E02-00E)

The high performance gauge pressure transmitter model EJA440A can be used to measure liquid, gas, or steam pressure. It outputs a 4 to 20 mA DC signal corresponding to the measured gauge pressure. Model EJA440A also features remote setup and monitoring through communications with the BRAIN™ terminal and CENTUM CS™ or μXL™ or HART® 275 host.

156 KB
Edition 23

EJA510A, EJA530A Absolute and Gauge Pressure Transmitters (GS 01C21F01-00E)

The absolute and gauge pressure transmitter model EJA510A and EJA530A can be used to measure liquid, gas, or steam pressure. Both output a 4 to 20 mA DC signal corresponding to the measured pressure, and also feature remote setup and monitoring through communications with the BRAIN™ terminal and CENTUM CS™ or μXL™ or HART® 275 host.

1.8 MB
Edition 12

EJX110B, EJX310B, and EJX430B Differential Pressure and Pressure Transmitters (GS 01C27B01-01EN)

The high performance differential pressure and pressure transmitters EJX110B, EJX310B, and EJX430B feature single crystal silicon resonant sensor and are suitable to measure liquid, gas, or steam flow as well as liquid level, density, and pressure. These transmitters transmit not only process variables but also the setting parameters using wireless signal. The transmitters run on internal batteries, and the installation cost can be decreased since hard-wiring is not required.

Edition 6

EJX118B and EJX438B Diaphragm Sealed Differential Pressure and Gauge Pressure Transmitter (GS 01C27H01-01EN)

Diaphragm seals are used to prevent process medium from entering directly into the pressure-sensing assembly of the differential pressure and pressure transmitters, they are connected to the transmitter using capillaries filled with fill fluid. EJX118B Diaphragm Sealed Differential Pressure and EJX438B Diaphragm Sealed Gauge Pressure Transmitters can be used to measure liquid, gas, or steam flow, as well as liquid level, density and pressure.

892 KB
Edition 12

EJX510B and EJX530B Absolute and Gauge Pressure Transmitter (GS 01C27F01-01EN)

The high performance absolute and gauge pressure transmitters EJX510B and EJX530B feature single crystal silicon resonant sensor and are suitable to measure liquid, gas, or steam pressure. EJX510B and EJX530B transmit not only process variables but also the setting parameters using wireless signal.

204 KB

EPDM O-Ring Material

EPDM 70-compound 55641 is a standard EPDM Terpolymer, Peroxide cured. It has a good compression resistance.

205 KB
Edition 2

ESB Bus Coupler Module (GS 32Q06L11-31E)

ESB Bus Coupler Module connects safety control units and safety node units via an ESB bus cable. Two ESB Bus Coupler Modules are mounted on the safety control unit (SSC60, SSC50, or SSC10).

230 KB
Edition 2

ESB Bus Coupler Module (for SSC60x, 2-Port) (GS 32Q06L10-31E)

ESB Bus Coupler Module connects safety control units and safety node units via an ESB bus cable. Two ESB Bus Coupler Modules are mounted on the safety control unit (SSC60).

601 KB
Edition 2

Ethernet Bus System  (GS 11B06A01-01E)

Process analyzers are typically maintained by maintenance personnel from the front of the analyzer. However, with the implementation of an analyzer bus system, maintenance can now be done entirely by monitoring and operating the analyzers from a remote location.

277 KB
Edition 3

Ethernet Communication Modules (GS 32Q06K51-31E)

This document describes about Model ALE111 Ethernet Communication Module used with a safety control station (SCS) for performing Modbus communication. By using the SCS's Modbus slave communication function, the data in SCS can be set or referred to by the Modbus master which is as separate system from SCS via a Ethernet communication module.

1.5 MB
Edition 10

EXA PH202 2-Wire pH/ORP Analyzer (GS 12B6C3-E-E)

Fieldbusses are based on highly reliable bi-directional com- munications between "smart" field devices and HOST systems. Next to a wide range of data each smart device can provide their status which is essential for adequate control and maintenance. The famous EXA sensor diagnostics will provide asset management facilities for those who operate and maintain the plant.

263 KB
Edition 31

Exaopc Interface Package (GS 36J02A10-01E)

As data sharing between information systems increases, the requirement to efficiently access and use plant information to meet business needs in a timely manner also increases. Within the process industry, the control room contains valuable information that has previously been inaccessible. 

1021 KB
Edition 2

EXAxt PH450 4-Wire Analyzer for pH and ORP (GS 12B07C05-01E)

The EXAxt 450 series is designed to combine the superior functionality of the Yokogawa EXA series with the ease of use offered in pocket computers (PDA). The PH450 offers the best accuracy in the industry by combining the pH measurement with advanced temperature compensation functionality, preloaded calibration standards and stability checks.

136 KB
Edition 3

Extension Module, Extension Base Unit (GS 04M01E01-21E)

The extension module and extension base unit allow you to install input modules in locations up to 30 m away from a DA100 data acquisition unit or its sub-units, saving on the number of cables wired to the input modules. Input modules thus connected are powered through the extension module from a sub-unit.

85 KB
Edition 3

F3LE01-5T Ethernet Interface Module (GS 34M06H24-01E)

The F3LE01-5T Ethernet* Interface Module is intended to be installed in an I/O slot of the FA-M3 Range-free Multi-controller. It can be connected to an IEEE802.3 compatible network (10BASE5 or 10BASE-T). The F3LE01-5T provides an Ethernet link similar to that of a personal computer via RS communication (n-to-n configuration).

266 KB
Edition 1

F3NC96-0N Positioning Module (with MECHATROLINK-II Interface) (GS 34M06H60-02E)

This positioning module is to be installed on the base unit of a FA–M3 range free controller system, and supports MECHATROLINK–II communications. The positioning module provides an interface (C1 master) to a high–speed motion field network based on MECHATROLINK–II, a standard proposed by Yaskawa Electric.

110 KB
Edition 6

F3XS04 Pulse Input Module (GS 34M06H54-01E)

The F3XS04 Pulse Input Module receives and counts pulse signals from the field. A single module can receive up to 4 channels of pulse signals.  It incorporates a 16-bit ring up-counter. The maximum ring value can be changed. It can have two preset values for each channel.

564 KB
Edition 6

FA-M3 - Analog Input Modules (GS 34M06H11-04E)

The F3AD04-0V is an analog-to-digital conversion input module for the FA-M3. 3 input signal range options are available: 0 to 5 V DC, 1 to 5 V DC, and -10 to 10 V DC. A single module can accommodate four input points. Four input points can be multiplexed during scanning.

232 KB
Edition 8

FA-M3 - Analog Input/output Modules Temperature Control and Monitoring Modules PID Control Module Open-circuit Detection Module (GS 34M06H11-01E)

The F3AD04-0N is an analog-to-digital conversion input module for the FA-M3. The input signal range can be selected from 0 V to 5 V DC, 1 V to 5 V DC, and -10 V to 10 V DC. A single module can accommodate four input points. Four input points can be multiplexed during scanning.

318 KB
Edition 1

FA-M3 - Analog Output Module (F3DA04-6R/DCR) (GS 34M06H11-06E)

The F3DA04-6R/DCR is a digital-to-analog conversion output module for use with the range-free controller FA-M3.

254 KB
Edition 1

FA-M3 - Analog Output Modules (GS 34M06H11-05E)

The F3DA04-6R is a digital-to-analog conversion output module for use with the range-free controller FA-M3.

172 KB
Edition 1

FA-M3 - ASi Master Module - F3LA01-0N (GS 34M06H33-01E)

The F3LA01-0N module is an AS-interface (ASi) master module to be installed in an I/O slot of the FA-M3R range-free controller. The ASi master module is compliant with AS-interface V2.1, and is capable of controlling up to 62 ASi slaves. The AS-interface is an open, reduced-wiring system compliant with the EN50295 standard designed to provide reduced wiring to proximity sensors, optical sensors, limit switches, indicators, and other bit-operated devices.

2.4 MB
Edition 13

FA-M3 - Basic Input/Output Modules (GS 34M06G01-01E)

The F3XH04 is a high-speed input module which incorporates the pulse-capture features of the FA-M3. The pulse-capture features facilitate detection of pulse inputs with shorter on-time than the scan period, which allows the F3XH04 to carry out photo-micro switch input for high-speed sensing. The interrupt mechanism ensures reliable interrupt processing using a short on-time pulse input.

3.2 MB
Edition 13

FA-M3 - Basic Modules (Base, Power Supply, CPU Modules and ROM Packs) (GS 34M06C01-01E)

FA-M3 base modules serve as the base for accommodating various modules. FA-M3 base modules are available in 4-, 5-, 6-, 9-, 13- and 16-slot versions. Choose an appropriate base module according to the target system requirements. There are no differences between main units and sub-units.

90 KB
Edition 2

FA-M3 - DeviceNet Scanner Module - F3LD01-0N (GS 34M06H28-01E)

The F3LD01-0N DeviceNet Scanner Module is an interface module that connects an FA-M3 system to DeviceNet. The module supports the DeviceNet's master function and controls a wide variety of field devices in a multi-vendor environment, from sensors and actuators to sophisticated devices.

108 KB
Edition 2

FA-M3 - Ethernet Interface Module - F3LE01-0T (GS 34M06H24-05E)

The Ethernet interface module is to be installed in an I/O slot of the FA-M3 Range-free Multi-controller. It can be connected to an IEEE802.3-compliant network (10BASE-T). The Ethernet interface module provides the FA-M3 controller with capabilities via Ethernet communication equivalent to the personal computer link (n:n connection) function via RS communication.

120 KB
Edition 2

FA-M3 - Ethernet Interface Module - F3LE11-0T (GS 34M06H24-02E)

The Ethernet Interface Module is to be installed in an I/O slot of the Range Free Multi-controller FA-M3. When installed, it allows the FA-M3 to connect with IEEE802.3 compliant networks (10BASE-T or 100BASE-TX), as well as send and receive electronic mails using SMTP or POP3 protocols.

105 KB
Edition 2

FA-M3 - Ethernet Interface Module - F3LE12-0T (GS 34M06H24-04E)

The Ethernet* Interface module is to be installed in an I/O slot of the FA-M3 Range-free Multi-controller. It can be connected to an IEEE802.3-compliant network (100BASE-TX or 10BASE-T). When connected to a network, it can exchange data with any node (PC, workstation, etc.) on the network using the TCP/IP or UDP/IP protocol.

559 KB
Edition 10

FA-M3 - FA Link H Modules FA-bus Modules (GS 34M06H43-01E)

The F3LP02-0N FA Link H Module provides a high-speed network that allows information exchange between the FA-M3 Range-free Multi-controllers. The F3LP02-0N is an FA link H interface module that provides a maximum of 32 stations of data link (one module is counted as one station).

108 KB
Edition 3

FA-M3 - FL-net (OPCN-2) Interface Module - F3LX02-1N (GS 34M06H32-02E)

FL-net (OPCN-2) is a vendor-independent, open FA network standard defined by the JOP work group of the Manufacturing Science and Technology Center (MSTC) of Japan for data exchange between programmable controllers (PLC), robot controllers (RC), computerized numerical control (CNC) machines, and other FA controllers.

55 KB
Edition 3

FA-M3 - GP-IB Communication Module - F3GB01-0N (GS 34M06H27-01E)

The F3GB01-0N is for connecting measuring instruments incorporating a GP-IB interface to each other. It has one GP-IB interface port. It supports master and slave modes, each of which provides separate interface capability. It can send interface messages in master mode.

1.7 MB
Edition 6

FA-M3 - High-speed Counter Modules and Positioning Modules (GS 34M06H51-01E)

The F3XP01-0H and F3XP02-0H High-speed Counter Modules connect to sensors such as incremental encoders, and receive and count the number of pulse signals up to a speed of 100 kips. It can count pulses as high speed as 100 kpps using a 32-bit counter. It contains two external coincidence outputs for each channel (two independent set values are allowed).

883 KB
Edition 4

FA-M3 - High-speed Data Acquisition Module - F3HA08-0N (GS 34M06H11-02E)

The F3HA08-0N module is an 8-channel analog input module to be installed in an I/O slot of the base module of the FA-M3 range-free controller. It can sample 4 channels concurrently. Its features include: 4-channel concurrent A/D conversion with shortest cycle time of 50 μs using 4 built-in A/D converters.

124 KB
Edition 1

FA-M3 - No-voltage Contact Input Module (Separate Commons) - F3XC08-0C (GS 34M06G01-02E)

The F3XC08-0C is a no-voltage contact input module to be installed on the FA-M3 accepting 8 no-voltage contact inputs. This module accepts 8 no-voltage contact inputs which are isolated from each other (separate commons).

231 KB
Edition 1

FA-M3 - NX Interface Module - F3NX01-0N (GS 34M06H29-01E)

The NX Interface Module is used for connecting to Autonomous Distributed Systems (NeXUS). It supports the Autonomous Distributed Protocol, and enables information interchange between FA-M3 systems and connections to PC, FA computers and other external equipment that supports Auto matic Distributed Protocol.

129 KB
Edition 1

FA-M3 - NX Interface Module - F3NX01-1N (GS 34M06H29-02E)

The NX Interface Module enables connection to a NeXUS Autonomous Distribution system. By supporting the Autonomous Distribution Protocol, it enables information interchange between FA-M3 systems and connections to PC, FA computers and other external devices that support the Autonomous Distribution protocol.

672 KB
Edition 10

FA-M3 - Personal Computer Link Modules UT Link Module RS-232-C / RS-422-A Communication Modules Ladder Communication Modules (GS 34M06H21-01E)

The F3LC11-1F is connected to a higher-level computer, such as a personal computer or FA computer, or a display for RS-232-C communications. It enables reading and writing of all FA-M3 devices. It does not require a transmission application program. It allows reading and writing of devices even when a ladder program is not running.

280 KB
Edition 2

FA-M3 - Positioning Module (with MECHATROLINK-III Interface) - F3NC97-0N (GS 34M06H60-03E) NEW

This positioning module is to be installed on the base module of an FA-M3 range-free controller system, and supports MECHATROLINK-III communications. It provides the C1 master function of the MECHATROLINK-III communications, transmitting MECHATROLINK-III commands to external equipment (slaves) according to instructions from a CPU module and receiving MECHATROLINK-III responses from external equipment.

283 KB
Edition 1

FA-M3 - Positioning Module (with Multi-channel Pulse Output) - F3YP14-0N,F3YP18-0N (GS 34M06H51-02E)

The F3YP14-0N and F3YP18-0N modules are positioning module with multi-channel pulse outputs. A single module can control four or eight motors (axes). As these modules output pulses, they are well-suited for position command type servo motors and drivers, or pulse motors and drivers.

198 KB
Edition 1

FA-M3 - PROFIBUS-DP Interface Module - F3LB01-0N (GS 34M06H34-01E)

The PROFIBUS-DP Interface module is a PROFIBUS-DP master module to be installed in an I/O slot of the FA-M3R range-free controller. The PROFIBUS-DP Interface module can control and communicate with a variety of sensors, actuators, and other remote I/O devices in the field.

2.8 MB
Edition 16

FA-M3 - Software Packages (GS 34M06N01-01E)

The SF630-MCW FA-M3 Programming Tool WideField3 for the FA-M3 sequence CPU modules allows a user to create and debug programs, as well as manage applications. With even better support for program reuse and the new script language, it dramatically increases programming efficiency.

206 KB
Edition 1

FA-M3 - Temperature Monitoring Module - F3CX04-0N (GS 34M06H11-03E)

The F3CX04-0N is a temperature monitoring module for the FA-M3. It occupies a single slot but can monitor four channels of temperature inputs. It features both high speed and high performance. The input sampling period is 200 ms (for four channels). The input conversion accuracy is 0.1% of full scale, and the input resolution is 0.1°C.

164 KB
Edition 24

FA-M3 - UL-approved, CE marking, C-Tick mark and KC mark - compliant Modules (GS 34M06C11-21E)

This table lists the modules for the FA-M3 range-free controller that are approved for the UL standard and comply with the CE marking, C-Tick mark and KC mark codes below.

455 KB
Edition 2

FA-M3 - YHLS Master Module YHLS Slave Units (for implementing high-speed remote I/O) (GS 34M06H46-01E)

The YHLS slave units are remote I/O units controlled by the YHLS master module (F3LH02-0N) via high-speed communication. The YHLS master module can control a maximum of 32 YHLS slave units per port. YHLS slave units are available in the following seven types to suit different applications.

586 KB
Edition 2

FA-M3 - YHLS Master Modules, YHLS Slave Units, YHLS Communication Cables (for implementing high-speed remote I/O) (GS 34M06H46-03E)

Yokogawa High-speed Link System (YHLS) Master Module has one or two communication ports to control remote slave units. It allows easy implementation of a 1-to-N high-speed remote I/O system. Up to 32 slave units can be connected to each connector to provide for a total of 2016 I/O points per port (1008 inputs and 1008 outputs).

352 KB
Edition 2

FA-M3 F3CU04-0N, F3CU04-1N Temperature Control and PID Module (GS 34M06H62-01E)

F3CU04-0N is a temperature control and PID module for the FA-M3.

437 KB
Edition 1

FA-M3 F3CU04-0S, F3CU04-1S Temperature Control and PID Module (GS 34M06H62-02E)

F3CU04-0S is a temperature control and PID module for the FA-M3.

652 KB
Edition 8

FA-M3 Fiber-optic Cables (GS 34M06C92-01E)

The KM6 fiber-optic cable is used for connecting Fiber-optic FA-bus Modules (F3LR01), Fiber-optic FA-bus Type 2 Modules (F3LR02) and Fiber-optic FA link H Modules (F3LP12). Several models are available for different applications

179 KB
Edition 9

FA-M3 Modules Comply with RoHS (2011/65/EU) (GS 34M06C11-22E)

This table lists the modules of the FA-M3 range-free controller that are approved for RoHS (2011/65/EU) below.

1.6 MB
Edition 22

FA-M3 Range-free Multi-controller (GS 34M06A01-01E)

The Range-free Multi-controller FA-M3 is a next-generation programmable controller, which achieves high per formance through its ultra high-speed processing and stable control features. It incorporates a space-saving compact design, supports versatile ranges with cover for up to 8192 input/output points, and is equipped with a variety of advanced modules, which can be used to configure a wide range of applications.

549 KB
Edition 7

FA-M3 Value (with Base, Supply, Sequence CPU and D I/O Modules) (GS 34M06C81-01E)

The F3SC21-1N (FA-M3 Value) is a compact programmable controller consisting of the following modules:

F3BU04-0N base module (with 4 slots)
F3SP05-0P sequence CPU module (with power supply and memory)
F3WD64-3N I/O module (with 32 inputs and 32 outputs)

312 KB
Edition 2

FAST/TOOLS Integration Engineering Package (GS 32Q04D20-31E)

This package runs on the safety engineering PC (SENG) and enables the integration between ProSafe-RS and FAST/TOOLS. This package is used for configuring a system which monitors and controls oil wells and oil pipe lines dotted in wide area. If this package is used, ProSafe-RS can not be integrated with CENTUM VP/CENTUM CS 3000 (hereinafter called VP/CS 3000).

3.7 MB
Edition 7

FAST/TOOLS Supervisory Systems (GS 50A01A10-01EN)

FAST/TOOLS has been developed with over 25 years of experience by combining our expertise in Supervisory Control And Data Acquisition (SCADA) with requirements from users and industry leaders. The FAST/TOOLS package is a powerful, modern, flexible, distributed operations information and control software package.

368 KB
Edition 2

FAST/TOOLS, ProSafe-RS Integration for Upstream (GS 50A01A11-01EN)

The development of oil and gas resources is growing at a fast pace due to rising worldwide demand for energy. Consequently, modern oil and gas fields are attracted to the deployment of new digital technologies in upstream well and pipeline processes in oil and gas exploration and production in order to achieve higher levels of efficiency and safety.

98 KB
Edition 5

FC13E & FC13U (GS 85A7C01-06EN)

The FC13 pan-tilt type explosion-proof or outdoor CCD color camera is compact and lightweight, making it suitable for installation in small spaces. The camera is an intelligent pan-tilt type, which has an embedded controller and can memorize preset point values.

140 KB
Edition 4

FC14E & FC14U (GS 85A7C01-08EN)

The FC14 Fixed angle zoom type explosion-proof or outdoor CCD color camera is compact and lightweight, making it suitable for installation in small spaces. The camera, which also has excellent durability, can be used for a wide range of applications, such as monitoring and diagnosis of facilities. 

147 KB
Edition 3

FC15U Camera (GS 85A7C01-11EN)

The FC15U High Rotation-speed pan-tilt type outdoor CCD color camera is compact and lightweight, making it suitable for installation in small spaces. The camera is an intelligent pan-tilt type, which has an embedded controller and can memorize preset point values. The camera employs an integrated structure which can be equipped with visible light illumination or infrared illumination.

4.2 MB
Edition 24

FCJ Autonomous Controller Hardware (GS 34P02Q11-01E)

This document describes the general specifications of the FCJ autonomous controller. (FCJ is an acronym of field control junction.)

3.0 MB
Edition 31

FCN Autonomous Controller Hardware (GS 34P02Q12-01E)

This document describes the general specifications of the FCN autonomous controller. (FCN is an acronym for field control node.)

585 KB
Edition 6

FCN-RTU Low Power Autonomous Controller Functions (GS 34P02Q02-01E)

This document describes the system configurations, development/maintenance, software configurations, and network specifications for a low power autonomous controller FCN-RTU.

2.7 MB
Edition 12

FCN-RTU Low Power Autonomous Controller Hardware (GS 34P02Q13-01E) NEW

This document describes the general specifications of the FCN-RTU low power autonomous controller. For functions, refer to FCN-RTU Low Power Autonomous Controller Functions, GS 34P02Q02-01E.

541 KB
Edition 19

FCN/FCJ Autonomous Controller Functions (GS 34P02Q01-01E)

This document describes the system configurations, development/maintenance, software configurations, network specifications, and installation requirements for two types of autonomous controllers in the STARDOM: FCN and FCJ. (FCN is an acronym for field control node, and FCJ for field control junction.)

558 KB
Edition 16

FCN/FCJ OPC Server for Windows (GS 34P02Q61-01E)

FCN/FCJ OPC Server for Windows (hereinafter referred to as simply FCN/FCJ OPC Server) is software that supports interfaces compliant with the OPC (OLE for Process Control) DA 2.05a (Data Access standard ver.2.05a) and A&E 1.10 (Alarms and Events standard ver.1.10), and it runs on a generic Windows-based computer.

200 KB
Edition 5

FCN/FCJ Simulator (GS 34P02Q77-01E)

FCN/FCJ Simulator is a software product that runs on a PC and simulates control applications running on a single FCN/FCJ. FCN/FCJ Simulator facilitates the debugging of control applications, thus improving development efficiency.

477 KB
Edition 17

FD20 Immersion Fitting (GS 12B6K2-01E-E)

For liquid analysis, the sensors are usually mounted in either a flow or an immersion fitting. Therefore Yokogawa has invested considarable design and development time in producing a full range of fittings with particular emphasis on designs that reduce installation and maintenance time and consequently save operation costs.

810 KB
Edition 17

FF20/FS20 Fittings for pH and ORP (GS 12B6K1-01E-E)

For liquid analysis, the sensors are usually mounted in either a flow or an immersion fitting. Therefore Yokogawa has invested considerable design and development time in producing a full range of fittings with particular emphasis on designs that reduce installation and maintenance time and consequently save operation costs.

61 KB
Edition 2

FHC13 Scene Manager (GS 85A7C01-07EN)

The FHC13 Scene Manager is a multiplexed controller for the FC13E/U or FC14E/U camerra, which incorporates the superimposing function and swithcher function as standard. The incorporation of the superimposing function in this instrument has made scene name displaying for every preset point in panning- tilting cameras, that previously required a complex system, simpler.

1.9 MB
Edition 14

Field Connection Specifications (GS 34P02Q30-01E)

This GS covers the connections between field devices and input/output modules for an FCN autonomous controller.

1.6 MB
Edition 2

Field Connection Specifications (for FIO) (GS 33K50H10-50E)

This GS describes the connection between the I/O Modules for FIO and field devices. The I/O Modules can be connected to field devices by terminal connection or with a terminal block via a KS cable interface adapter. A customer-furnished MIL cable can also be used to connect to the I/O Module.

2.8 MB
Edition 4

Field Device Connection (for ProSafe-RS) (GS 32Q06J10-31E)

This GS explains how to connect I/O modules of the ProSafe-RS to field devices.

979 KB

Field Mounting Rate Totalizer

The 202Ai Loop Powered Rate Totalizer is designed to operate with any flow meter which produces a 4-20mA output, including differential pressure devices, magnetic or vortex flow meters. The 202Ai is powered entirely from the 4-20mA current loop and has a maximum of 2.5 volts drop across the input.

1.4 MB
Edition 6

Field Wireless System Overview (GS 01W01A01-01EN)

This General Specifications (GS) describes features of a field wireless system, system configuration a field wireless network, system configuration devices, and connection with the host system.

1.1 MB
Edition 12

Flange Mounted Differential Pressure Transmitter (GS 01C27C01-01EN)

The high performance flange mounted differential pressure transmitter EJX210B features single crystal silicon resonant sensor and is suitable to measure levels of densities of solidifying or precipitating liquids. EJX210B transmits not only process variables but also the setting parameters using wireless signal.

452 KB

FLEXIFIT BIO FLEXIFIT U BIO

The FLEXIFIT BIO can be used in many applications. It can be cleaned easily. The sensor head is protected by three steel pins. The FLEXIFIT U BIO does not have the protecting steel pins. Please note that the o-ring position has to be specified when ordering the FLEXIFIT BIO and FLEXIFIT U BIO.

230 KB

FLEXIFIT TC

The FLEXIFIT TC can be used in many applications. It can be cleaned easily. The sensor head is protected by three steel pins. The FLEXIFIT TC is designed for use hygienic TriClamp process connections.

10.3 MB
Edition 1

For Remote Diaphragm Seals with Yokogawa Trans. (GS SLC22A0-02E-A)

PI Components Corporation is a major industry supplier of remote components and systems. Remote seal systems are filled systems used with pressure transmitters when the process or installation conditions require it. Commonly used on aggressive or high temperature installations, remote seal systems protect the transmitter and its sensor from extreme conditions.

506 KB
Edition 10

FOUNDATION™ fieldbus Communication Module (GS 34P02Q55-01E)

This document describes the hardware specifications of the NFLF111 FOUNDATION fieldbus communication module to be installed in an FCN (field control node) autonomous controller. The NFLF111 functions as a link master (LM) device capable of controlling communication schedules on the H1 fieldbus segment connected to each of its port and performs data exchange between the FCN and fieldbus devices.

1.7 MB
Edition 5

Fourier Transform Near-Infared Analyzer (GS 12Y03A03-01E)

The NR800 Fourier Transform Near-Infrared Analyzers offers high-resolution, high S/N (signal-to-noise) ratio, and wide wavelength scanning range measurement with its newly developed interferometer and detector. The NR800 also offers high stability, vibration resistance, and durability, inheriting features from NR500 earlier successful models.

370 KB
Edition 1

FPSU Power Supply Unit (GS 77J50P01-01E)

This FPSU is a power supply unit that is available in cases where the JUXTA signal conditioner of 24 V DC power supply is used in AC power source. CSA compliant. Even if one FPSU fails, the parallel connection enables the backup operation by another FPSU.

52 KB
Edition 3

FTU-16, FTU-18, FTU-04 Power Distributor Unit (GS JF83-01E)

This unit can supply power in block up to 16 units of JUXTA transmitters.

905 KB
Edition 4

FVX110 Fieldbus Segment Indicator (GS 01S01C01-01EN)

The FVX110 is a field indicator that allows you to switch and display up to 16 indicated values for FOUNDATION™ fieldbus devices. Turn the scroll knob on the case to switch displays. No complex operation is needed in the field and you can observe the indicated values easily.

778 KB
Edition 2

FX1 series Computing units (Variable software type) (GS 77J08X01-01E)

The JUXTA FX1 Series, Computing unit (Variable Software Type) receives voltage input signals, applies various computing functions to them, and outputs isolated DC current or DC voltage signals to controllers or recorders. The computation parameters, zero points, and spans can be set and modified using a Handy Terminal (JHT200).

525 KB
Edition 2

FX2 series Computing units (Variable/Fixed software type) (GS 77J08X02-01E)

The JUXTA FX2 Series, Computing unit (Variable/Fixed Software Type) receives a voltage input signal, applies various computing functions to it, and outputs isolated DC current or DC voltage signals to controllers or recorders.

834 KB
Edition 2

FX3 series Computing units (mV input/valuable software type) (GS 77J08X03-01E)

The JUXTA FX3 Series, Computing unit (mV Input/ Variable Software Type) receives mV input signals, applies various computing functions to them, and outputs isolated DC current or DC voltage signals to controllers or recorders. The computation parameters, zero points, and spans can be set and modified using a Handy Terminal (JHT200).

528 KB
Edition 2

FX4 series Computing units (mV Input/Fixed software type) (GS 77J08X04-01E)

The JUXTA FX4 Series, Computing unit (mV Input/Fixed Software Type) receives a voltage input signal, applies various computing functions to it, and outputs isolated DC current or DC voltage signals to controllers or recorders.

237 KB
Edition 6

Gas Flow Calculation Portfolio (GS34P02P31-01E)

This general specification document describes the Gas Flow Calculation Portfolio on FCN/FCJ autonomous controllers. Using this portfolio, gas flow rate is calculated on robust and hazardous certified STARDOM controllers FCN/FCJ while control logics are running.

618 KB
Edition 1

GC Maintenance Terminal  (GS 11B03G03-01E)

Two types of communications are provided for GC1000 Mark II process gas chromatograph: DCS and personal computer (PC) communications. DCS communication transmits analytical and other data to a DCS systems, such as CENTUM, in digital form. PC communication is provided for maintenance of GC1000 Mark II. 

1.2 MB
Edition 3

GC1000 Mark II Process Gas Chromatograph (GS 11B03A03-01E)

A Gas Chromatograph analyzes a gas or volatile liquid sample by separating components for detection. The discrete separation and positive identification of components and measurement of the composition with no interference is a positive advantage of the gas chromatograph.

357 KB
Edition 4

GC1000MarkII and GCAS Modbus Communication (GS 11B03G02-02E)

The Modbus protocol is used for DCS communication with the GC1000 MarkII. This communication protocol was first established for the Programmable Logic Controller (PLC) made by Gould, Inc., and is now used as a standard communication protocol between different systems.

375 KB
Edition 2

GC8000 Modbus Communication (GS 11B08B02-01E)

The Modbus protocol is used for DCS communication with the GC8000. This communication protocol was first established for the Programmable Logic Controller (PLC) made by Gould, Inc., and is now used as a standard communication protocol between different systems.

6.7 MB
Edition 3

GC8000 Process Gas Chromatograph (GS 11B08A01-01E)

A Process Gas Chromatograph analyzes a vapor or volatile liquid sample and then separates the various chemical components in the sample for individual detection and measurement. The discrete separation and positive identification of components and measurement of the composition enables the process gas chromatograph to be one of the few analyzer types available that minimizes the likelihood of cross interference during measurement.

186 KB
Edition 2

General Specification - MLA & MLD Loop Powered Process Indicators (GS 61A01A-01E-A)

The Model MLA and MLD field mounted indicators receive DC voltage or current signals by electronic Transmitters and indicate process measurement values. Standard models are NEMA4X and Explosion Proof.

222 KB
Edition 4

General Specification - MLX Loop Powered Process Indicator (GS 60A02S01-01E-A)

The Model MLX Loop-Powered Process Indicator receives DC current signals from electronic transmitters and indicates process measurement values. Standard models are general purpose.

316 KB
Edition 5

General Specification - YHC5150X FieldMate Handheld Communicator (GS 01R01A30-01EN-A)

The YHC5150X FieldMate Handheld Communicator is the latest Intrinsically Safe HART ® communicator from Yokogawa Corporation of America. All HART ® field devices can be configured, polled, and trimmed utilizing a Wi ndows-Embedded CE™ based system for faster processing and greater storage capacity. In addition, all options are standard, and no subscrip tion is required. The YHC5150X is a full function, DD Direct, HART ® Communicator supporting Universal, Common Practice and Device Specific commands for commissioning, configuration, and maintenance operations.

204 KB
Edition 29

General Specifications - EJA110A (GS 01C21B01-00E)

The high performance differential pressure transmitter model EJA110A can be used to measure liquid, gas, or steam flow as well as liquid level, density and pressure. It outputs a 4 to 20 mA DC signal corresponding to the measured differential pressure. Model EJA110A also features remote setup and monitoring through communications with the BRAIN™ terminal and CENTUM CS™ or XL™ or HART® 275 host.

2.0 MB
Edition 6

General Specifications - EJA110E (GS 01C31B01-01EN)

1.7 MB
Edition 5

General Specifications - EJA115E (GS 01C31K01-01EN)

2.9 MB
Edition 6

General Specifications - EJA118E (GS 01C31H01-01EN)

189 KB
Edition 24

General Specifications - EJA120A (GS 01C21B03-00E)

1.6 MB
Edition 7

General Specifications - EJA120E (GS 01C31B03-01EN)

1.7 MB
Edition 5

General Specifications - EJA130E (GS 01C31B04-01EN)

190 KB
Edition 25

General Specifications - EJA210A / EJA220A (GS 01C21C01-00E)

The high performance flange mounted differential pressure transmitter models EJA210A and 220A can be used to measure levels of densities of solidifying or precipitating liquids. Both output a 4 to 20 mA DC signal corresponding to the measured differential pressure. Models EJA210A and 220A also feature remote setup and monitoring through communications with the BRAIN™ terminal and CENTUM CS™ or XL™ or HART® 275 host.

2.5 MB
Edition 6

General Specifications - EJA210E (GS 01C31C01-01EN)

1.8 MB
Edition 5

General Specifications - EJA310E (GS 01C31D01-01EN)

2.1 MB
Edition 5

General Specifications - EJA430E (GS 01C31E01-01EN)

2.6 MB
Edition 6

General Specifications - EJA438E (GS 01C31J03-01EN)

1.8 MB
Edition 5

General Specifications - EJA440E (GS 01C31E02-01EN)

1.5 MB
Edition 8

General Specifications - EJA510E and EJA530E (GS 01C31F01-01EN)

2.2 MB
Edition 20

General Specifications - EJX110A (GS 01C25B01-01EN)

305 KB
Edition 3

General Specifications - EJX110A (0.025% Accuracy) (GS 01C25B01-10E)

The high performance differential pressure transmitter EJX110A features single crystal silicon resonant sensor and is suitable to measure liquid, gas, or steam flow as well as liquid level, density and pres- sure. EJX110A outputs a 4 to 20 mA DC signal corresponding to the measured differential pressure. 

2.0 MB
Edition 12

General Specifications - EJX115A (GS 01C25K01-01EN)

3.0 MB
Edition 16

General Specifications - EJX118A (GS 01C25H01-01EN)

1.6 MB
Edition 13

General Specifications - EJX120A (GS 01C25B03-01EN)

1.9 MB
Edition 14

General Specifications - EJX130A (GS 01C25B04-01EN)

2.6 MB
Edition 17

General Specifications - EJX210A (GS 01C25C01-01EN)

1.7 MB
Edition 13

General Specifications - EJX310A (GS 01C25D01-01EN)

1.7 MB
Edition 19

General Specifications - EJX430A (GS 01C25E01-01EN)

2.7 MB
Edition 17

General Specifications - EJX438A (GS 01C25J03-01EN)

2.0 MB
Edition 13

General Specifications - EJX440A (GS 01C25E02-01EN)

1.7 MB
Edition 20

General Specifications - EJX510A and EJX530A (GS 01C25F01-01EN)

1.7 MB
Edition 10

General Specifications - EJX610A and EJX630A (GS 01C25F05-01EN)

2.0 MB
Edition 21

General Specifications - EJX910A (GS 01C25R01-01EN)

1.9 MB
Edition 12

General Specifications - EJX930A (GS 01C25R04-01EN)

86 KB
Edition 18

General Specifications - Fieldbus Communication (GS 01C22T02-00E)

General Specification for EJA-A Series FOUNDATION Fieldbus.

794 KB
Edition 11

General Specifications - FieldMate 3.0 (GS 01R01A01-01E) NEW

560 KB
Edition 7

General Specifications - FlowNavigator (GS 01C25R51-01EN)

The FSA120 (FieldMate FlowNavigator) is the software package which offers various functions to help users to easily configure the mass flow parameters of device. The FSA120 includes following two programs:

  • EJXMVTool: for EJX Multivariable Transmitter
  • DYFMVTool: for digitalYEWFLO Vortex Flow Meter
147 KB
Edition 9

General Specifications - HART Communication (GS 01C22T01-00E)

General Specifications for EJA-A series HART communication.

83 KB
Edition 9

General Specifications - Profibus Communication (GS 01C22T03-00E)

General Specification for EJA-A series Profibus PA communication.

880 KB
Edition 1

General Specifications - YTA70P (GS 01C50C05-01EN)

3.0 MB
Edition 3

General Specifications: M-800 Series 2, 3, 5-Valve Manifolds for Bottom Mount EJA/EJX Transmitters (GS 22B01C54-01EN-A)

The PGI M-800 Series two-valve, three-valve and five-valve manifolds are designed for use with the bottom-mount configuration used on the EJA/EJX transmitters. These wafer style manifolds provide a retrofit to similar existing installations found in many plants.

2.6 MB
Edition 1

GM10 Data Acquisition Module GM90MB Module Base GM90PS Power Supply Module (GS04L55B01-01EN) NEW

2.2 MB
Edition 10

GP10/GP20 Paperless Recorder (Portable type) GX90XA/GX90XD/GX90YD I/O Modules (GS 04L52B01-01EN)

The GP10/GP20 are portable type paperless recorders that display real-time measured data on a touch screen and save data on an external storage medium (SD card).

2.2 MB
Edition 10

GX10/GX20 Paperless Recorder (Panel mount type) GX90XA/GX90XD/GX90YD I/O Modules (GS 04L51B01-01EN)

The GX10/GX20 are paperless recorders that display real-time measured data on a touch screen and save data on an external storage medium (SD card).

2.8 MB
3.0 MB
Edition 4

GX90XA/GX90XD GX90YD/GX90WD I/O Modules (GS04L53B01-01EN) NEW

I/O modules are connected to the GX/GP and Expandable I/O unit.

  • A module type is four types, an analog input, a digital input, a digital output, and a digital input/ output. 
  • Input and output have module structure and it can extend them easily.
449 KB
Edition 4

Hardware (Controller) - AEP7D Primary Power Supply Bus Unit (GS 33K50K40-50E) NEW

This hardware GS covers the AEP7D Primary Power Supply Bus Unit which distributes power to equipment mounted in the same cabinet. The AEP7D is designed to operate from two independent power sources "A" and "B" and provide seven sets of outputs corresponding to each input. 

526 KB
Edition 4

Hardware (Controller) - Analog I/O Modules (for FIO) (GS 33K50F60-50E)

This document describes about hardware specifications of Analog I/O Modules (for FIO) to be installed in the ESB bus node units (ANB10S and ANB10D), Optical ESB bus node units (ANB11S and ANB11D), ER bus node units (ANR10S and ANR10D) (*1), and field control units (for FIO) (AFV30S, AFV30D, AFV40S, AFV40D, AFV10S, AFV10D, AFF50S, and AFF50D).

734 KB
Edition 5

Hardware (Controller) - ARM15A, ARM55[] , ARS15B, ARS15M, ARS55M Relay Boards (for FIO) (GS 33K50H60-50E) NEW

This document describes the specifications of relay board used in FIO subsystem of CENTUM VP. Relay input/ output boards are connected in between digital input/output modules (for FIO) and field devices. Relay input boards receive contact signals or voltage input signals of field devices.

311 KB
Edition 5

Hardware (Controller) - Digital I/O Modules (for FIO) (GS 33K50F70-50E) NEW

This GS covers the hardware specifications of the Digital I/O Modules (FIO) that can be installed in the Node Unit for ESB Bus (ANB10S, ANB10D, ANB11S, ANB11D), the Node Unit for ER Bus (ANR10S, ANR10D) and the Field Control Unit (AFV30S, AFV30D, AFV40S, AFV40D, AFF50S, AFF50D, AFV10S, AFV10D).

386 KB
Edition 1

Hardware (Controller) - Field Connection Specifications (for I/O Modules with Built-In Barrier and FIO) (GS 33K50H30-50E)

This GS describes the connection between the Modules with Barrier (FIO) and field devices. When installing these apparatuses with intrinsically safe circuit, "Explosion Protection" (TI 33Q01J30-01E) and "Explosion Protection of FIO Products" (IM 33Y06K01-90E) for CENELEC Approval should be referenced together with this GS.

604 KB
Edition 8

Hardware (Controller) - FIO System Overview (for Vnet/IP) (GS 33K50F10-50E) NEW

The FIO (Fieldnetwork I/O) System is connected to the Field Control Unit (FCU) via an ESB, optical ESB, or ER bus. The Field Control Unit (AFV30/AFV40) is connected to an ESB Bus Node Unit (ANB10) or an Optical ESB Bus Node Unit (ANB11). The Field Control Unit (AFV10) is connected to an ESB Bus Node Unit (ANB10) or an ER Bus Node Unit (ANR10).

339 KB
Edition 4

Hardware (Controller) - I/O Modules with Built-in Barrier (for FIO) (GS 33K50F80-50E) NEW

This document describes about I/O Modules with Built-in Barrier (for FIO) which can be installed in Zone 2 or Division 2 and connected to devices located in Zone 0, 1, or Division 1. These modules have galvanic isolation between the field interface and systems but they do not have isolation between channels.

255 KB
Edition 4

Hardware (Controller) - Model ACB41 I/O Expansion Cabinet (for FIO) (GS 33K55K10-50E)

The I/O Expansion Cabinet is used to install a Node Unit (NU) and Compact Field Control Unit (for FIO). It can be mounted beside a field control unit (FCU) or separately. A Node Unit and Compact Field Control Unit (for FIO) can be installed at the front and rear of the cabinet.

418 KB
Edition 5

Hardware (Controller) - Model ACB51 I/O Expansion Cabinet (for AFV30[] /AFV40[]) (GS 33K50K10-50E) NEW

The ACB51 I/O Expansion Cabinet is used to install an ESB Bus Node Unit, Optical ESB Bus Node Unit, and Unit for Optical ESB Bus Repeater Module. It can be installed beside a Field Control Unit (AFV40) or separately. Node units and other units can be installed at the front and rear of the cabinet.

468 KB
Edition 4

Hardware (Controller) - Model ACUKT1 Cabinet Utility Kit (for Rittal Cabinet, AFV30[]) (GS 33K50K20-50E) NEW

The ACUKT1 Cabinet Utility Kit is used to install in high density a Field Control Unit (AFV30), ESB Bus Node Unit (ANB10), Optical ESB Bus Node Unit (ANB11), and Unit for Optical ESB Bus Repeater Module (ANT10U) in the Rittal TS8 Cabinet. Temperatures and fans in the cabinet can be monitored on HIS by connecting to the HK bus.

459 KB
Edition 5

Hardware (Controller) - Model AEPV7D Power Supply Bus Unit, Vertical Type (for Cabinet Mounting) (GS 33K50K41-50E) NEW

These General Specifications (GS) describe the AEPV7D Primary Power Supply Bus Unit, which distributes power to the units installed in the same cabinet. The AEPV7D is designed to be able to receive power from two different power sources independently.

373 KB
Edition 6

Hardware (Controller) - Model ALE111 Ethernet Communication Module (for FIO) (GS 33K50G11-50E)

This document describes about Model ALE111 Ethernet Communication Module (for FIO) that a field control station (FCS) uses to perform Ethernet communication with subsystems such as FA-M3. This Ethernet communication module can be mounted on field control units (AFV30, AFV40, AFV10, and AFF50), ESB bus node unit (ANB10), optical ESB bus node unit (ANB11), and ER bus node unit (ANR10).

339 KB
Edition 3

Hardware (Controller) - Model ALP111 PROFIBUS-DP Communication Module (for FIO) (GS 33K50G80-50E)

This document describes about Model ALP111 PROFIBUS-DP Communication Module (for FIO) which performs as the PROFIBUS-DP master device to communicate and exchange data with PROFIBUS-DP slave devices. This PROFIBUS-DP communication module can be mounted on field control units (AFV30, AFV40, AFV10, and AFF50), ESB bus node unit (ANB10), optical ESB bus node unit (ANB11), and ER bus node unit (ANR10).

420 KB
Edition 4

Hardware (Controller) - Model ALP121 PROFIBUS-DP Communication Module (for FIO) (GS 33K50G85-50E)

This document describes about Model ALP121 PROFIBUS-DP Communication Module (for FIO) which performs as the PROFIBUS-DP master device (referred to as the master device) to communicate and exchange data with PROFIBUS-DP slave devices (*1) (referred to as the slave device).

267 KB
Edition 5

Hardware (Controller) - Model ANT10U Unit for Optical ESB Bus Repeater Module (for AFV30[] /AFV40[] ) (GS 33K50F50-50E) NEW

This unit is used to install Optical ESB Bus Repeater Module. It can be used to connect the Optical ESB bus in a star or chain configuration. In a star configuration, this unit functions as the hub of the Optical ESB bus.

217 KB
Edition 2

Hardware (Controller) - Model EB401 ER Bus Interface Master Module (for FIO) (GS 33K50F40-50E)

The ER Bus Interface Master Module is the communication module to connect the ESB Bus Node Unit or the Field Control Unit (for FIO) with the ER Bus Node Unit using ER bus. This module can be installed in the ESB Bus Node Unit (ANB10S, ANB10D) and the Field Control Unit (for FIO) (AFF50S, AFF50D, AFV10S, AFV10D).

216 KB
Edition 2

Hardware (Controller) - Model EC401 ESB Bus Coupler Module (for FIO) (GS 33K50E50-50E)

The ESB Bus Coupler Module is a communication module to connect the Field Control Unit and the Node Unit for ESB Bus via the ESB bus. This module can be installed in the Field Control Unit for FIO (AFV30S, AFV30D, AFV40S, AFV40D, AFV10S, AFV10D, AFF50S and AFF50D).

243 KB
Edition 2

Hardware (Controller) - Model EC402 ESB Bus Coupler Module (for AFV30[] /AFV40[] , 2-Port) (GS 33K50E51-50E)

The ESB Bus Coupler Module is a communication module to connect the Field Control Unit and the Node Unit for ESB Bus via the ESB bus. This module can be installed in the Field Control Unit for FIO (AFV30S, AFV30D, AFV40S, AFV40D). By installing two modules in the Field Control Unit for FIO, dual-redundant ESB bus can be configured.

609 KB
Edition 4

Hardware (Controller) - Models AFV10S, AFV10D Field Control Unit Duplexed Field Control Unit (for Vnet/IP and FIO, 19-inch Rack (GS 33K50E30-50E)

This GS covers the hardware specifications of the Field Control Unit (FCU) which is the core of the control function of the Field Control Station (FCS). For the installation specifications and the environmental conditions common to the systems, refer to "Vnet/IP System Overview (Vnet/IP Edition)" (GS 33K01A10-50E).

468 KB
Edition 6

Hardware (Controller) - Models AFV30S, AFV30D Field Control Unit Duplexed Field Control Unit (for Vnet/IP and FIO, 19-inch Rack (GS 33K50E10-50E) NEW

This GS covers the hardware specifications of the Field Control Unit (FCU) which is the core of the control function of the Field Control Station (FCS). These products are subject to the Export Administration Regulations (EAR) by the United States Department of Commerce, Bureau of Industry and Security (BIS).

896 KB
Edition 6

Hardware (Controller) - Models AFV40S, AFV40D Field Control Unit Duplexed Field Control Unit (for Vnet/IP and FIO, with Cabinet) (GS 33K50E20-50E) NEW

This GS covers the hardware specifications of the Field Control Unit (FCU) which is the core of the control function of the Field Control Station (FCS). For the installation specifications and environmental conditions that are common to the systems, refer to "Integrated Production Control System CENTUM VP System Overview (Vnet/IP Edition)" (GS 33K01A10-50E).

458 KB
Edition 3

Hardware (Controller) - Models ALR111, ALR121 Serial Communication Modules (for FIO) (GS 33K50G10-50E)

This document describes about Models ALR111 and ALR121 Serial Communication Modules (for FIO) that a field control station (FCS) uses to perform serial communication with subsystems such as FA-M3. These serial communication modules can be mounted on field control units (AFV30, AFV40, AFV10, and AFF50), ESB bus node unit (ANB10), optical ESB bus node unit (ANB11), and ER bus node unit (ANR10).

264 KB
Edition 7

Hardware (Controller) - Models ANB10S, ANB10D ESB Bus Node Units (for FIO) (GS 33K50F20-50E) NEW

The ESB Bus Node Unit has an interface function that communicates the analog I/O signals and contact I/O signals of a field with a Field Control Unit (FCU) via an ESB bus, as well as a function that supplies power to the I/O Modules. This node units are connected to FCU via an ESB bus.

287 KB
Edition 6

Hardware (Controller) - Models ANB11S, ANB11D Optical ESB Bus Node Unit (for AFV30 [] /AFV40 [] ) (GS 33K50F30-50E) NEW

This node unit collects and relays I/O signals from a remote location to a FCU. It is equipped with a function to convert field analog I/O signals and contact I/O signals to optical signals and transmit them to the FCU in a remote location via the optical ESB bus, as well as a function to supply power to the I/O modules.

340 KB
Edition 5

Hardware (Controller) - Models ANR10S, ANR10D ER Bus Node Unit (for FIO) (GS 33K50F21-50E)

ER Bus Node Unit has an interface function that communicates the analog I/O signals and contact I/O signals of a field with a Field Control Unit (FCU), as well as a function that supplies power to the I/O Modules.

314 KB
Edition 4

Hardware (Controller) - Models ANT401, ANT502 Optical ESB Bus Repeater Module for 5km (for AFV30[] /AFV40[] ) (GS 33K50F51-50E)

The Optical ESB Bus Repeater Module converts the ESB bus to an optical signal and transmits it. The ESB bus transmission distance can be extended within the range of up to 5 km by connecting the ANT401 Optical ESB Bus Repeater Master Module and ANT502 Optical ESB Bus Repeater Slave Module with an optical fiber cable.

320 KB
Edition 4

Hardware (Controller) - Models ANT411, ANT512 Optical ESB Bus Repeater Module for 5 km to 50 km (for AFV30[]/AFV40[]) (GS 33K50F52-50E)

The Optical ESB Bus Repeater Module for 5 km to 50 km converts the ESB bus to an optical signal and transmits it. The ESB bus transmission distance can be extended within the range from 5 km to 50 km by connecting the ANT411 Optical ESB Bus Repeater Master Module and ANT512 Optical ESB Bus Repeater Slave Module with an optical fiber cable.

770 KB
Edition 5

Hardware (Controller) - Models PW601, PW602 24 V DC Output Power Supply Model AEP9D Secondary Power Supply Bus Unit (GS 33K50K30-50E) NEW

This GS covers the hardware specifications of the 24 V DC Output Power Supply (PW601, PW602) which supplies power to a Fieldbus power supply or a digital module of FIO, and covers also the hardware specifications of the Secondary Power Supply Bus Unit which branch received electricity from 24 V DC power supply (PW60, etc.) to equipment installed in the cabinet.

165 KB
Edition 2

Hardware (Controller) - Signal Conditioner Cards (GS 33K50H80-50E)

Signal Conditioner Cards, which interface to the process, are installed in Signal Conditioner Nests. The signal conditioner cards can convert the I/O signals, isolate the I/O signals, and provide an isolated power supply from a built-in distributor. For example, the measuring ranges of temperature and mV input signal conditioner cards can be changed by a portable BRAIN terminal.

616 KB
Edition 1

Hardware (Controller) - Signal Conditioner Nests Signal Conditioner Nest Fan Unit (GS 33K50H70-50E)

The Signal Conditioner Nests are 19"-rack-type nests for mounting I/O signal conditioner cards. Model MHM nest for control I/O cards and model MHC nest for general I/O cards are available. AC power supply unit can be redundant.

659 KB
Edition 2

Hardware (Controller) - Terminal Boards (for FIO) (GS 33K50H50-50E)

This document describes the specifications of terminal boards used for FIOs of CENTUM VP systems.

2.2 MB
Edition 1

Hardware (Controller) - Terminal Boards Terminal Blocks Relay Boards (for RIO and ST compatible FIO) (GS 33K55R40-50E)

Terminal boards are used to connect field I/O signals to I/O modules (for RIO and ST compatible FIO) in I/O module nests of control stations. Terminal blocks are used to connect I/O signals to I/O modules. Relay input boards are connected to digital signals from the field and provide one/two contact output signals per input.

814 KB
Edition 1

Hardware (Controller) - Turbomachinery I/O Modules (GS 33K50F90-50E)

This document of General Specification (GS) contains the hardware specifications of the Turbomachinery I/O Modules (FIO). For the field control stations that are applicable for the Turbomachinery I/O Modules, please refer to "Turbomachinery I/O Module Logic Builder Package" (GS 33K10U10-50E).

316 KB
Edition 1

Hardware (Controller) -Terminal Block (for I/O Modules with Built-In Barrier and FIO) (GS 33K50H40-50E)

This GS covers the hardware specifications of the Terminal Block that can be used for Modules with Built-In Barrier (FIO) of CENTUM VP. When installing these apparatuses with intrinsically safe circuit, "Explosion Protection" (TI 33Q01J30-01E) and "Explosion Protection of FIO Products" (IM 33Y06K01-90E) for CENELEC Approval should be referenced together with this GS.

592 KB
Edition 3

Hardware (HMI) - Model AIP830 - Operation Keyboard for Single- loop Operation (GS 33K50C32-50E) NEW

This document describes the hardware specifications of AIP830 Operation Keyboard for Single-loop Operation for Desktop Type HIS. It contains an independent USB speaker (a sound function) other than buzzing alarms (buzzer sounds). An AIP830 keyboard can be used per one Desktop Type HIS.

209 KB
Edition 3

Hardware (HMI) - Model LPCKIT - Enclosed Display Style Console Assembly (GS 33K50B40-50E) NEW

This GS covers the hardware specifications of LPCKIT Enclosed Display Style Console Assembly. You can use the assembly as Human Interface Station installing a genaral-purpose PC in it.

177 KB
Edition 3

Hardware (HMI) - Model VI702 - Vnet/IP Interface Card (GS 33K50C10-50E) NEW

By installing the control bus interface card into the PCI Express slot of the PC/AT compatible computer, the computer is connected to Vnet/IP.

280 KB
Edition 2

Hardware (HMI) - Model YAX101 - Desk for CENTUM (GS 33K50C50-50E) NEW

The 19" rack mountable devices can be placed on a desk for CENTUM. For the installation specifications and environmental conditions common to the systems, refer to the "System Overview" (GS 33K01A10-50E, GS 33K01A20-50E)

212 KB
Edition 3

Hardware (HMI) - Model YAX801 - General-purpose Desk (YPCKIT Console Style) (GS 33K50C40-50E) NEW

The YAX801 is a desk that can be installed side by side with a YPCKIT Open Display Style Console Assembly. For the installation and environmental conditions common to CENTUM VP systems, "System Overview" (GS 33K01A10-50E, GS 33K01A20-50E).

315 KB
Edition 6

Hardware (HMI) - Model YPCKIT - Open Display Style Console Assembly (GS 33K50B50-50E) NEW

This GS covers the hardware specifications of YPCKIT Open Display Style Console Assembly. You can use the assembly as Human Interface Station installing a PC in it.

275 KB
Edition 4

Hardware (Network) - Model AVR10D Duplexed V net Router (GS 33K50D10-50E) NEW

These Bus Converters connect CENTUM VP Human Interface Stations (HISes) on the Vnet/IP to CENTUM VP/CENTUM CS 3000/CENTUM CS stations on the V net, CENTUM CS 1000 stations on the VL net in other domain. To connect to CENTUM CS 3000/CENTUM CS System, LHS4450 Multiple Project Connection Package and LHS5450 Multiple Project Connection Builder are required.

39 KB

Hardware Interchange

342 KB
Edition 5

HART Communication Functions (GS 34P02Q53-01E)

This general specifications (GS) document describes the HART Communication Function that can be implemented in the Autonomous Controller FCN. The Autonomous Controller FCN can communicate with HART field devices.

237 KB

HCS HART Concentrator System (225-710-04B)

The HCS HART Concentrator System converts a HART digital signal to a serial (RS-485 or RS-232) MODBUS RTU communication protocol. This allows HART transmitters and valves to interface directly with MODBUS-based monitoring and control systems

491 KB

HIMHART Smart HART loop Interface and Monitor (224-710-07D)

The HIM HART Loop Interface and Monitor unlocks the full potential of new and in-place smart HART multivariable transmitters and valves. The HIM allows up to three additional analog process variable measurements from a smart device with no additional process penetrations or wiring.

232 KB
Edition 2

IAC24 Integral Auto Calibration Unit Specification (TI 11M12A01-91E-A)

The IAC-24 is a dramatically new approach to automatic calibration equipment. It has no user adjustable parts and it is only 4 inches wide! Just connect the calibration and reference gases, set the correct pressure, and let the device and analyzer do the rest. There are no gas flow meter or calibration tube head losses to worry about.

1.4 MB
Edition 4

Inductive Conductivity PR10 Retractable fitting (GS 12D8J2-02E-E)

On-line measurements always present extra challenges compared to at-line measurements. For example when maintenance needs to be done. Applications where the sensors has to be removed without interruptions or shut-downs the PR10 is especially suitable. Without any special tools the PR10 can be retracted safely from the process up to 5 bar.

3.2 MB
Edition 19

Industrial Electrodes for pH/ORP (GS 12B6J1-E-E)

Selecting the proper pH electrode for an application can be a challenging exercise. The heart of a pH measuring loop is the electrode system. Yokogawa has designed a wide range of electrodes to ensure this heart keeps beating under the most severe conditions.

275 KB
Edition 6

Input Modules - AI-517-01 - Analog Input Module (open < 2.8 mA) (GS 48C17Z01-00E-N)

This Analog Input module, or trip amplifier, contains two circuits and can be utilized for various applications. The open line detection level is configured for 2.8 mA.

275 KB
Edition 6

Input Modules - AI-517-B1 - Analog Input Module (open < 3.8 mA) (GS 48C17B01-00E-N)

This Analog Input module, or trip amplifier, contains two circuits and can be utilized for various applications. The open line detection level is configured for 3.8 mA.

248 KB
Edition 5

Input Modules - AI-917-00 - Analogue Input Module (2x 0-20 mA, 2x 0-10 V) (GS 48D17Z00-00E-N)

This module has four analogue inputs and four logic pulse outputs. The module is programmable, so the functionality depends on the loaded application program. Various standard application programs are available and specified in separate documents. 

248 KB
Edition 4

Input Modules - AI-917-A0 - Analogue Input Module (4x 0-20 mA) (GS 48D17A00-00E-N)

This module has four analogue inputs and four logic pulse outputs. The module is programmable, so the functionality depends on the loaded application program. Various standard application programs are available and specified in separate documents. The loaded program and its version can be read from the LCD front panel display and from the labels located on both CPUs.

248 KB
Edition 4

Input Modules - AI-917-B0 - Analogue Input Module (4x 0-10 V) (GS 48D17B00-00E-N)

This module has four analogue inputs and four logic pulse outputs. The module is programmable, so the functionality depends on the loaded application program. Various standard application programs are available and specified in separate documents. The loaded program and its version can be read from the LCD front panel display and from the labels located on both CPUs.

248 KB
Edition 2

Input Modules - AI-917-C0 - Analogue Input Module (2x 0-1 V, 2x 0-10 V) (GS 48D17C00-00E-N)

This module has four analogue inputs and four logic pulse outputs. The module is programmable, so the functionality depends on the loaded application program. Various standard application programs are available and specified in separate documents. The loaded program and its version can be read from the LCD front panel display and from the labels located on both CPUs.

248 KB
Edition 2

Input Modules - AI-917-D0 - Analogue Input Module (0-20 mA, 0-1 V, 2x 0-10 V) (GS 48D17D00-00E-N)

This module has four analogue inputs and four logic pulse outputs. The module is programmable, so the functionality depends on the loaded application program. Various standard application programs are available and specified in separate documents. The loaded program and its version can be read from the LCD front panel display and from the labels located on both CPUs.

247 KB
Edition 2

Input Modules - AI-917-E0 - Analogue Input Module (4x 0-1 V) (GS 48D17E00-00E-N)

This module has four analogue inputs and four logic pulse outputs. The module is programmable, so the functionality depends on the loaded application program. Various standard application programs are available and specified in separate documents. The loaded program and its version can be read from the LCD front panel display and from the labels located on both CPUs.

187 KB
Edition 4

Input Modules - DI-511-05 - Digital Input Module (fail-safe) (GS 48C11Z05-00E-N)

The digital input module is intended as digital field input signal converter to ProSafe-SLS logic signals. This digital input module has 8 channels. Each chan nel exists of a galvanically isolated voltage input converter to fail-safe pulse logic signals. The module is provided with 8 red LED's, indicating the outputs of the channels.

88 KB
Edition 2

Interface for CMMS (R3) (GS 33Y05Q20-32E)

nterface for CMMS is a package used to connect Plant Resource Manager (PRM) with Maximo, a computerized Maintenance Management System (CMMS). This provides information online for PRM and CMMS.

122 KB
Edition 2

Interface for GE Energy's System 1® (R3) (GS 33Y05Q22-32E)

The Interface for GE's System 1 is a PRM optional package for connecting PRM with the System 1 Optimization and Diagnostics Software Platform. System 1 is a condition monitoring and event diagnostics software platform for managing the plant machinery assets. It is used for monitoring and diagnosing the rotating or reciprocating equipment and optimizing plant operations.

239 KB
Edition 4

IR200 Infared Gas Analyzer (GS 11G02M01-01E)

The IR200 infrared gas analyzer is capable of measuring the concentrations of CO2, CO, CH4, SO2, NO and O2 components in sample gas. CO2, CO, CH4, SO2 and NO are measured by non-dispersive infrared method (NDIR), while O2 is measured by paramagnetic or zirconia method.

283 KB
Edition 4

IR400 Infared Gas Analyzer (GS 11G02N01-01E)

The IR400 infrared gas analyzer is capable of measuring the concentrations of NO, SO2, CO2, CO, CH4 and O2 components in sample gas. NO, SO2, CO2, CO and CH4 are measured by non-dispersive infrared method (NDIR), while O2 is measured by built-in paramagnetic sensor or external zirconia sensor.

368 KB
Edition 6

ISC202 2-wire Conductivity Analyzer (GS 12D8B3-E-E)

Fieldbusses are based on highly reliable bi-directional communications between "smart" field devices and HOST systems. Next to a wide range of data each smart device can provide their status which is essential for adequate control and maintenance. The famous EXA sensor diagnostics will provide asset management facilities for those who operate and maintain the plant.

819 KB
Edition 13

ISC40FF/ISC40FS Flow Fittings and NPT Adapters (GS 12D8J2-E-E)

The model ISC40 sensors are designed for use with the EXA: ISC40G(S) 2-wire transmitters and the EXA: ISC450G 4-wire analyzers. This combination exceeds all expectations for conductivity measurement in terms of: reliability, accuracy, rangeability and price performance.

363 KB
Edition 2

ISC450 4-Wire Analyzer for Inductive Conductivity (GS 12D8B5-E-E)

The new EXAxt 450 series has been designed to meet the highest market requirements of today's industry. This series of analyzers is unique as it will no longer be the uncertainty factor of your quality demands, but instead will bring you to a higher level. 

132 KB

JK12 Alarm Setter (GS JK12-01E)

This unit inputs DC voltage or current signal and converts it into alarm contact point after comparing it with internal setup value. Dual alarm outputs. Can setup alarm operating point, lockup width, operating direction, ON ready time, OFF ready time through Handy Terminal. Output relay can select excitation/non-excitation of normal time.

91 KB
Edition 2

Juxta F Series Model FB2A CT Transmitter (Mean Value) (GS JF06-02E)

This instrument converts AC current signals from CT output, etc., to current or voltage signals. AC/DC conversion is made by mean value. 

97 KB
Edition 2

Juxta F Series Model FG2A PT Transmitter (Mean Value) (GS JF08-02E)

This instrument converts AC current signals from CT output, etc., to current or voltage signals. AC/DC conversion is made by mean value. 

96 KB
Edition 2

Juxta F Series Model FH9A/V Linearizer (GS JF16-01E)

This signal conditioner converts nonlinear signals generated by analyzers and noise meters, etc., to linear current or voltage signals. Incorporation of one-chip microcomputer provides high efficiency and superior performance. Use of Handy Terminal allows easy on-site zero and span adjustment, and I/O monitoring.

97 KB
Edition 2

JUXTA F Series Model FR8A/V RTD Transmitter (non-isolated) (GS JF35-01E)

This signal conditioner functions as a resistance bulb sensor to output current or voltage signals. Non-isolated type. 

97 KB
Edition 2

JUXTA F Series Model FR9A/V Dew Point Transmitter (GS JF34-01E)

This signal conditioner functions as a dew-point sensor to convert dew point temperature into current or voltage signals. Incorporation of one-chip microcomputer provides high efficiency and superior performance. Use of Handy Terminal allows easy onsite zero and span adjustment, burnout selection, and I/O monitoring. 

94 KB
Edition 2

JUXTA F Series Model FS4A/V Potentiometer Transmitter (non-isolated) (GS JF38-01E)

This signal conditioner converts the resistance change of potentiometer fitted in motor operated valve or air duct damper, etc., to current or voltage signals. Non-isolated type.

148 KB

Life Cycle Assessment Result (lca-ProSafee)

* Assessed based on the sample system of total 510 I/O (AI, AO, DI, and DO) points between ProSafe-RS and ProSafe-PLC.

129 KB
Edition 9

LL100 PC-based Parameters Setting Tool (GS 05G01B12-01E)

The LL100 PC-based Parameters Setting Tool is a software package used to set the setup parameters, operating parameters, and program patterns* of the GREEN Series controllers from a personal computer. This tool allows users to download, upload, print out parameters, and display PV trend data during PID tuning, etc.

90 KB
Edition 5

LL1100 PC-based Parameters Setting Tool (For US1000) (GS 05G01A01-01E)

The LL1100 PC-Based Parameters Setting Tool is a software package used to set the setup parameters and operation parameters of the US1000 Digital Indicating Controller from a personal computer. This tool allows users to download, upload, and print out parameters, display PV trend data during PID tuning, etc., and has an online help function that provides operation guidance.

97 KB
Edition 5

LL1200 PC-based Custom Computation Building Tool (For US1000) (GS 05G01A11-01E)

The LL1200 PC-Based Custom Computation Building Tool is a software package used to create custom computation and custom display functions for the US1000 Digital Indicating Controller. This tool also covers the functions of the LL1100 PC-Based Parameters Setting Tool. 

133 KB
Edition 9

LL200 PC-based Custom Computation Building Tool (GS 05G01B22-01E)

The LL1200 PC-Based Custom Computation Building Tool is a software package used to create custom computation and custom display functions for the US1000 Digital Indicating Controller. This tool also covers the functions of the LL1100 PC-Based Parameters Setting Tool. 

499 KB
Edition 6

LL50A Parameter Setting Software with Ladder Program Building Function (GS 05P05A01-01EN)

The LL50A Parameters Setting Software is designed to build and set parameters, program pattern, ladder programs, and the like of the UTAdvanced digital indi- cating controllers from a PC. The tuning and monitor- ing of ladder programs are possible during communi- cation with the controllers.

161 KB
Edition 3

Logic and Timer Modules - FM-550-02 - Logic Module (GS 48C50Z02-00E-N)

This logic function module has two multiple input AND gates with OR gate expansions. The module is suitable for fail-safe applications. For TÜV SIL4 applications the maximum number of OR gate expansion inputs is restricted to 2.

166 KB
Edition 4

Logic and Timer Modules - FM-551-03 - Logic Module (GS 48C51Z03-00E-N)

This logic function module has three multiple input AND gates with OR expansions. The module is suited for fail-safe applications. For TÜV SIL4 applications the maximum number of OR gate expansion inputs is restricted to 2.

167 KB
Edition 4

Logic and Timer Modules - FM-552-03 - Logic Module (GS 48C52Z03-00E-N)

This logic function module has four multiple input AND gates with OR expansions. The module is suited for fail-safe applications. Channels 1-3 are 3 input AND gate with one OR gate expansion input. Channel 4 is a 2 input AND gate with two OR gate expansion inputs. The module is provided with 4 red LED's, indicating the outputs of the channels.

172 KB
Edition 4

Logic and Timer Modules - FM-553-02 - Logic Module (GS 48C53Z02-00E-N)

This logic function module has five 2 NOR gate inputs and 2 inverters. Channel 2 is suitable as change-over switch in fail –safe applications. The module is provided with 8 red LED's, indicating the outputs of the channels. The module is equipped with monitoring circuitry for connection to the Sequence of Event Recording (SER) system.

163 KB
Edition 4

Logic and Timer Modules - FM-556-00 - Logic Module (GS 48C56Z00-00E-N)

This logic function module has four two input AND gates with OR expansions and inverters. The module is suited for fail-safe applications. For TÜV SIL4 applications the maximum number of OR gate expansion inputs is restricted to 2 and inverter inputs should not be used. The module is provided with 4 red LED's, indicating the outputs of the channels. 

166 KB
Edition 4

Logic and Timer Modules - FM-557-00 - Logic Module (GS 48C57Z00-00E-N)

This logic function module has five two input AND gates with OR expansion on one input. The module is suited for fail-safe applications. The module is provided with 5 red LED's, indicating the outputs of the channels. The module is equipped with monitoring circuitry for connection to the Sequence of Event Recording (SER) system.

204 KB
Edition 4

Logic and Timer Modules - TI-540-01 - Timer Module (0.5 s – 70 h) (GS 48C40Z01-00E-N)

This timer module has two multiple function timers with logic pulse input and output and is suitable for a wide range of timer settings. The timer counts back to zero from a value set by the connector strapping. The timer is suitable for various time functions. For Fail-Safe applications the two timers should be wired to a 2 input AND gate

202 KB
Edition 4

Logic and Timer Modules - TI-540-A1 - Timer Module (7 ms – 16 m) (GS 48C40A01-00E-N)

This timer module has two multiple function timers with logic pulse input and output and is suitable for a wide range of timer settings. The timer counts back to zero from a value set by the connector strapping. The timer is suitable for various time functions. For Fail-Safe applications the two timers should be wired to a 2 input AND gate.

148 KB
Edition 3

Logic and Timer Modules - TI-544-00 - Fail-Safe Timer Module (GS 48C44Z00-00E-N)

This module contains a single channel fail-safe delay-off Timer circuit. Timer setting is done by connector strapping. The ti mer is suitable for a timer range of 1.5 - 310s. The delay function is based on the controlled discharge of a capacitor. The input signal is used to generate a pulse of approximately 1 second which fully charges the capacitor(s).

286 KB

LR Series - LR12000E, LR8100E, LR4100E, LR4200E

762 KB
Edition 3

M-650, M-750 and M-651 3-Valve Manifolds for Differential Pressure (GS 22B01C52-01EN-A)

The PGI 3-Valve manifolds are designed for mounting on differential pressure transmitters having 2-1/8" center-to-center connections. The M-650 directly mounts to the transmitter, replacing the process connectors by providing 1/2" NPT process connections. M-750 manifolds are also available and provide a flange face for the process connectors to be mounted.

1.5 MB
Edition 3

M-675, M-775 and M-678 5-Valve Manifolds for Natural Gas Differential Pressure (GS 22B01C53-01EN-A)

The PGI 5-Valve manifolds are designed for natural gas service and provide bubble-tight seats and seals. Static pressure and calibration test connections are standard and located conveniently on the Instrument Side Flange. The five valves provide the flexibility to test the differential pressure and static pressure measurement capability of the Differential Pressure transmitters.

997 KB

M1115NL Wireless I/O With MESH Network Technology (DS 04R09D01-01E)

The DAWN M1115NL is a new industrial wireless I/O and protocol interface module that uses advanced mesh networking technology to provide secure and reliable wireless communications. Equipped with easy to use web browser configuration support, M1115NL radios can be configured via a wired network interface or over the air via their wireless interface.

408 KB
Edition 1

M25 and M251 2-Valve In-Line Manifolds for Gauge Pressure (GS 1C22-AGC-05)

The M251 and M25 are two-valve, single outlet valves for use with direct-mount transmitters, EJA/EJX530A and EJA/EJX510A. These combine isolation, calibration, and venting capability in a single compact unit. The simple direct-mount design reduces potential leak paths and minimizes installation time.

78 KB
Edition 5

M3: Report computation function For data aquisition unit DA100 and hybrid recorder DR series (GS 04M01B01-31E)

This function assigns measurement and/or computation channels as report channels, and creates statistical information. The report computation can be selected from hourly report, daily report and monthly report. Chart printing takes place automatically whenever the report creation time (in the case of the DR recorder) is reached. 

1.4 MB
Edition 2

M4T 3-Valve Manifolds for Differential Pressure (GS 1C22-AGC-02)

The M4 three-valve manifolds were designed for mounting on differential pressure transmitters having 2 1/8" center-to-center connections. The M4T directly mounts to the transmitter, replacing the process connectors by providing 1/2" NPT process connections.

975 KB
Edition 2

M4TP 2-Valve Manifolds for Gauge Pressure (GS 1C22-AGC-03)

The M4TP two-valve, block and bleed, manifolds were designed for mounting on gauge pressure transmitters having the industry standard for traditional style flanges and process connections, like on the EJA/EJX430A transmitters.

2.8 MB
Edition 2

M6T 5-Valve Manifolds for Natural Gas Differential Pressure (GS 1C22-AGC-01)

The M6 manifolds were designed for natural gas service and provide leak tight Delrin® Seats. Static pressure and calibration test connections are standard. The five valves provide the flexibility to test the differential pressure and static pressure measurement capability of the DPharp transmitters.

93 KB
Edition 3

MA4 Distributor (Non-isolated) (GS JM46-01E)

Model MA-4 plug-in type Distributor for 2-wire transmitter has compatible functions of distributor and single conversion.

73 KB
Edition 1

MA5 Distributor(Free Range) (GS 77J04A05-01E)

The MA5 is a plug-in type distributor that is used in combination with a two-wire type transmitter to convert the transmitter's 4 to 20 mA DC signals into isolated DC current or DC voltage signals. Output range setting, selection of square root extractor and breakpoint linearization (breakpoint setting), I/O adjustment, I/O monitoring, and loop back test can be made using the optional Parameter Setting Tool (VJ77) or Handy Terminal (JHT200).

86 KB
Edition 1

MA5D Distributor(2-output, Free Range Type) (GS 77J04A05-02E)

The MA5D is a plug-in type distributor that is used in combination with a two-wire type transmitter to convert the transmitter's 4 to 20 mA DC signals into isolated DC current or DC voltage signals. Output range setting, selection of square root extractor and breakpoint linearization (breakpoint setting), I/O adjustment, I/O monitoring, and loop back test can be made using the optional Parameter Setting Tool (VJ77) or Handy Terminal (JHT200).

49 KB
Edition 2

MA7 Distributor (United Signal Type) (GS 77J04A07-01E)

The MA7 is a plug-in type distributor that is used in combination with a two-wire type transmitter to convert the transmitter's 4 to 20 mA DC signals into isolated 4 to 20 mA DC current or 1 to 5 V DC voltage signals. 

56 KB
Edition 2

MA7D Distributor (Dual-output and United Signal Type) (GS 77J04A07-02E)

The MA7D is a insulated dual-output, plug-in type dis- tributor that is used in combination with a two-wire type transmitter to convert the transmitter's 4 to 20 mA DC signals into isolated 4 to 20 mA DC current or 1 to 5 V DC voltage signals.

106 KB
Edition 5

MB1 CT Transmitter (GS JM05-01E)

This plug-in type model MB1 CT transmitter receives AC current signal of CT output, etc. and converts it into isolated DC current or voltage signal. 

301 KB
Edition 4

MC1/AC1 Single Channel Calibration Units (GS 11M6AA-01E-A)

Yokogawa's zirconia oxygen detector systems offer a variety of calibration units for quick, easy control of calibration and reference gases giving the user simple, accurate calibration and operation. Users with single- point measuring systems, such as the model ZR402 converter, may choose either manual or automatic calibration units, models MC1 or AC1, respectively.

75 KB
Edition 3

MC1B Loop Powered Isolator (GS JM58-01E)

This loop powered isolator inputs 4∼20mA DC signal and outputs 4∼20mA DC signal.

99 KB
Edition 4

MCT7 CT Transmitter (GS MCT7-01E)

This plug-in type CT transmitter receives AC current signal such as output from CT and converts it into isolated 4∼20mA DC or 1∼5V DC signal. 

103 KB
Edition 3

MD1 Tachometer Transmitter (GS JM63-01E)

Model MD1 Tachometer Transmitter is a plug-in type signal conditioner to convert single phase AC voltage signal from tacho-generator into isolated voltage or current signal. 

116 KB
Edition 3

Memory Card Module (GS 34M06C22-01E)

The Memory Card Module provides support for compact flash memory when it is mounted in an I/O slot of the Range Free Multi-controller FA-M3. When installed, it allows contents of CPU module devices to be saved as files to the compact flash. Likewise, device data can be read from such files and be written to the CPU module.

101 KB
Edition 4

MG1 PT Transmitter (GS JM07-01E)

This plug-in type Model MG1 PT transmitter receives AC voltage signal of PT output, etc. and converts it into isolated DC current or voltage signal. 

50 KB
Edition 2

MH1 Isolator (GS 77J04H01-01E)

The MH1 is a plug-in type isolator that receives DC current or DC voltage signals to convert them into isolated DC current or DC voltage signals.

57 KB
Edition 2

MH1D Isolator (Dual-output Type) (GS 77J04H01-02E)

The MH1D is a dual-output, plug-in type isolator that receives DC current or DC voltage signals to convert them into isolated DC current or DC voltage signals.

74 KB
Edition 1

MH5 Isolator (Free Range Type) (GS 77J04H05-01E)

The MH5 is a plug-in type isolator that converts DC current or DC voltage signals into isolated DC current or DC voltage signals. I/O range setting, selection of square root extractor and breakpoint linearization (breakpoint setting), I/O adjustment, I/O monitoring, and loop back test can be made using the optional Parameter Setting Tool (VJ77) or Handy Terminal (JHT200).

81 KB
Edition 1

MH5D Isolator (2-output, Free Range Type) (GS 77J04H05-02E)

The MH5D is a plug-in type isolator that converts DC current or DC voltage signals into isolated DC current or DC voltage signals. I/O range setting, selection of square root extractor and breakpoint linearization (breakpoint setting), I/O adjustment, I/O monitoring, and loop back test can be made using the optional Parameter Setting Tool (VJ77) or Handy Terminal (JHT200).

47 KB
Edition 2

MH7 Isolator (United Signal Type) (GS 77J04H07-01E)

The MH7 is a plug-in type isolator that receives 1 to 5 V DC voltage or 4 to 20 mA DC current signals to convert them into isolated 1 to 5 V DC voltage or 4 to 20 mA DC current signals.

54 KB
Edition 2

MH7D Isolator (Dual-output and United Signal Type) (GS 77J04H07-02E)

The MH7D is a dual-output, plug-in type isolator that receives 1 to 5 V DC voltage or 4 to 20 mA DC current signals to convert them into isolated 1 to 5 V DC voltage or 4 to 20 mA DC current signals.

126 KB
Edition 5

MHF Super High Speed Isolator (GS JM20-01E)

Model MHF Super High Speed Isolator is a plug-in type signal conditioner to convert DC voltage or current signal into isolated DC voltage or current signal. 

554 KB
Edition 3

MIL Connector Terminal Blocks and Cables (GS 34P02Q43-01E)

This General Specification (GS) sheet describes MIL connector cables and MIL connector terminal blocks enabling connections to field control node (FCN) autonomous controllers. These MIL connector cables and connector terminal blocks are MIL connector-equipped (MIL-C-83503-compliant) cables and connectors.

136 KB
Edition 1

ML2 RS232C/RS485 Converter (GS 77J04L02-01E)

This plug-in type RS-232C/RS-485 dual directional (half duplex) converter has two ports of RS-232C and RS-485. Between these two ports, isolation, level conversion and active control of driver are performed. This converter is mainly used to connect RS-232C of personal computer with the instruments equipped with RS-485.

117 KB
Edition 2

MLC Load Cell Transmitter (GS MLC-01E)

This plug-in type load cell transmitter supplies bridge voltage to load cell (distortion gage) etc. It receives mV signal from load cell and converts it into DC voltage or current signals. 

166 KB
Edition 8

Modbus Communication Portfolio (GS 34P02P21-01E)

This describes Modbus Communication Portfolio for STARDOM. Modbus Communication Portfolio easily allows FCN/FCJ to be Modbus-capable through serial or Ethernet communications.

1.0 MB

Model 202Di - Field Mounting Rate Totalizer

The 202Di Field Mounting Rate Totalizer requires no external power and is designed to operate with turbine, positive displacement and paddle-wheel flow meters in applications such as irrigation systems and pipelines, and as a replacement for mechanical registers.

473 KB
Edition 1

Model 212 - Heat Calculator (BU 01P11A02-E-U)

The 212 Heat Calculator is designed to measure the energy consumed in hot water heating systems and chilled water cooling systems. The 212 will interface with a wide range of flow meters, including vortex and magnetic flow meters with pulse outputs, positive displacement and inferential water meters, turbine and paddle wheel flow meters.

385 KB
Edition 3

Model 475 Field Communicator (GS 475COMM-01E)

The 475 Field Communicator establishes the new standard for handheld communicators. With a full-color user interface, powerful diagnostic capabilities, and fast start up and operating times, the 475 Field Communicator will power your experience and simplify your work in the field.

37 KB
Edition 5

Model ADMAG AE Fieldbus Communication (GS 01E07F01-00E)

Fieldbus is the digital communication line for the field instruments, whose signal is internationally standardized by Fieldbus FOUNDATION. The Fieldbus bi-directional digital communication performance makes possible for the field instruments and the control devices to be a complete on-line system, superseding the existing analog transmission lines.

502 KB
Edition 3

Model AIP831 Operation Keyboard for Eight-loop Simultaneous Operation Model LHS1140 Eight-loop Simultaneous Operation (GS 33K50C33-50E) NEW

AIP831 is an Operation Keyboard for Eight-loop Simultaneous Operation for CENTUM VP's Desktop Type HIS. AIP831 is equipped with 8-Loop Control keys which contains touch sensors for sensing the touches. (Touch sensors are used for "Instrument Faceplate Highlight" function of Desktop Type HIS.)

318 KB
Edition 3

Model ALF111 FOUNDATION fieldbus Communication Module (for FIO) (GS 33K50G20-50E)

This document describes about Model ALF111 FOUNDATION fieldbus Communication Module (for FIO) which is to establish communication between field control stations (FCS) and fieldbus devices compliant to the FOUNDATION fieldbus (H1) such as transmitters and valve positioners.

265 KB
Edition 4

Model AM012 Magnetic Flow Simulator (GS 01E06K02-00E)

AMO12 is a signal generator used to check the calibration and operation of AM11 Magnetic Flow Converters, AM12 Magnetic Flow Converters, AM100A/200A-Integral Type Magnetic Flow Meter, YMA11 Magnetic Flow Converter, Compact YEWMAG Magnetic Flow Meter (style A and style B) and Admag AE Magnetic Flow Meter.

53 KB
Edition 14

Model AM11 Magnetic Flow Converter (GS 01E06C01-00E)

The AM11, ADMAG series magnetic flow converter has multi-functions and high performance. It supports various outputs, display formats, self-diagnostics function, batch control function etc. The optimum converter can be selected among 4 types on demand to realize excellent flow measurement.

35 KB
Edition 2

Model AR-HP Arrester for 2 Wire Type Pulse Signal (GS AR06-01E)

This high quality arrester protects electronic instruments by absorbing induced lightning surge voltage. Arrester should be set between lines through which surges are entered and serves to protect instruments such as transmitters or receivers safely from thunder inducement.

35 KB
Edition 2

Model AR-LP Arrester for 2 Wire Type Pulse Signal (GS AR05-01E)

This high quality arrester protects electronic instruments by absorbing induced lightning surge voltage. Arrester should be set between lines through which surges are entered and serves to protect instruments such as transmitters or receivers safely from thunder inducement.

34 KB
Edition 3

Model AR-PH Arrester for Power Supply (GS AR32-01E)

This high quality arrester protects electronic instruments by absorbing induced lightning surge voltage. Arrester should be set between lines through which surges are entered and serves to protect instruments such as transmitters or receivers safely from thunder inducement.

34 KB
Edition 3

Model AR-PS Arrester for Power Supply (GS AR31-01E)

This high quality arrester protects electronic instruments by absorbing induced lightning surge voltage. Arrester should be set between lines through which surges are entered and serves to protect instruments such as transmitters or receivers safely from thunder inducement.

37 KB
Edition 3

Model AR-RT Arrester for RTD/Potentiometer (GS AR04-01E)

This high quality arrester protects electronic instruments by absorbing induced lightning surge voltage. Arrester should be set between lines through which surges are entered and serves to protect instruments such as transmitters or receivers safely from thunder inducement.

37 KB
Edition 3

Model AR-SA Arrester for Current Signal (GS AR01-01E)

This high quality arrester protects electronic instruments by absorbing induced lightning surge voltage. Arrester should be set between lines through which surges are entered and serves to protect instruments such as transmitters or receivers safely from thunder inducement.

37 KB
Edition 2

Model AR-SP Arrester for 3 Wire Type Pulse Signal (GS AR07-01E)

This high quality arrester protects electronic instruments by absorbing induced lightning surge voltage. Arrester should be set between lines through which surges are entered and serves to protect instruments such as transmitters or receivers safely from thunder inducement.

35 KB
Edition 3

Model AR-TC Arrester for Thermocouple (GS AR03-01E)

This high quality arrester protects electronic instruments by absorbing induced lightning surge voltage. Arrester should be set between lines through which surges are entered and serves to protect instruments such as transmitters or receivers safely from thunder inducement.

66 KB
Edition 3

Model AR2-ET Arrester for Ethernet (GS 77M02N21-01E)

This high-quality arrester protects communication equipment connected to a network, configured with Ethernet (100BASE-TX/10BASE-T) or token ring, by absorbing induced lightning surge voltage generated from lightning discharges.

334 KB
Edition 5

Model AW810D Wide Area Communication Router (GS 33K50D20-50E) NEW

Wide Area Communication Router (WAC Router) is the hardware equipment to connect Vnet/IP domains via Wide Area Network (WAN). Operations and monitoring of the FCS/SCS that are distributed
in remote areas can be realized. Satellite communications can also be used as a WAN.

382 KB
Edition 12

Model BA10 and WF10 Junction box and Connecting cable (GS 12B6W2-01E-E)

Between measuring plant and control room, especially when the distance between these places is greater than the length of the standard appropriate electrode cables, the connecting equipment can be an expedient method for connecting sensor cables to a measuring instrument.

154 KB
Edition 3

Model CHS5400 Electronic Instruction Manual (GS 32Q01W10-31E)

The manuals of ProSafe-RS are provided as the electronic documents in a DVD-ROM. The file format is Portable Document Format (PDF). Refer to the GS "ProSafe-RS Safety Instrumented System Overview" (GS 32Q01B10-31E, GS 32Q01B20-31E). As for the Software, Adobe Reader 10.1 and 9.5 can be used.

305 KB
Edition 1

Model DA0 Output Isolator (Voltage Input/Current Output Type) (GS 77J05A10-01E)

The DA0 is a nest-mounting type DCS-supported isolator that receives 1 to 5 V DC signals from DCS, and converts them into isolated 4 to 20 mA DC or 10 to 50 mA DC signals.

387 KB
Edition 1

Model DA1 Distributor (GS 77J05A01-01E)

The DA1 is a nest-mounting type DCS-supported distributor, is used in combination with a two-wire transmitter, and converts 4 to 20 mA DC signals into isolated DC current or DC voltage signals.

370 KB