Mid-Level UT55A/UT52A

Die UT55A- und UT52A-Temperaturregler verwenden ein einfach abzulesendes großes LCD-Farbdisplay mit 14 Segmenten sowie Navigationstasten. Dies erhöht die Überwachungs- und Bedienungsmöglichkeiten erheblich. Die Regler bieten zusätzlich eine serienmäßige Ladder-Sequenzfunktion. Der Regler spart durch seine geringe Tiefe Platz im Instrumentenpult. Darüber hinaus unterstützen die UT55A/UT52A-Temperaturregler offene Netzwerke wie etwa die Ethernetkommunikation.

UT55A und UT52A Eigenschaften der Temperaturregler

  • Bis zu 4 analoge Eingänge verfügbar
  • 3 alarmunabhängige allgemeine Anschlüsse serienmäßig
  • Sie können Ladder-Sequenzprogramme erstellen
  • Einfache Bedienung
  • Bis zu 18 digitale Ausgänge (Kombinationen möglich)
  • Mithilfe des enthaltenen detaillierten Code-Modells können Sie die Spezifikationen an Ihre Anforderungen anpassen.

Details

Gehobene Regelung

8 integrierte Regelungsfunktionen

Die Regelungsfunktion ermöglicht es, Einstellungen ganz einfach zu konfigurieren und Parameter zu ändern.

  • Einschleifen-Regelung
  • Hauptschleifen-Kaskadenregelung
  • Sekundärschleifen-Kaskadenregelung
  • Kaskadenregelung
  • Schleifenregelung für Backup
  • Schleifenregelung mit PV-Schaltung
  • Schleifenregelung mit automatischer PV-Wahl
  • Regelung mit PV-Haltefunktion

8 built-in Control Mode

8 integrierte Regelungsarten

  • PID-Regelung
  • EIN/AUS-Regelung (1 Hysteresepunkt)
  • EIN/AUS-Regelung (2 Hysteresepunkte)
  • Zweipositionen-/Zweistufenregelung
  • Heiz-/Kühlregelung
  • Sample-PI-Regelung
  • Batch-PID-Regelung
  • Vorregelung

8 Built-in Control Types

Bitte beachten Sie die Spezifikationen zu jedem Modell für den Zusammenhang zwischen dem obigen Regelungsmodus und den Regelungsarten für jedes Modell.

Ladder-Sequenzregelung

Die integrierte Ladder-Sequenzregelung erweitert den Umfang der Anwendungen erheblich. Diese Funktion ist serienmäßig in allen UT-Advanced-Reglern enthalten (außer UM33A). Die Ladder-Sequenzregelungsfunktion kann eine kleine von der Anwendung benötigte SPS ersetzen. Die Sequenzregelung und die PID-Regelung sind gleichzeitig möglich.

  • Überwachung und Regelung externer Maschinen
    Z. B.: Lampen, Schalter, Timer
  • Erstellen Sie ganz einfach Eingangs-/Ausgangs-Logikfunktionen.
    Anzahl der Standardbefehlsarten: 13
    Anzahl der Anwendungsbefehlsarten: 73
[Beispiel einer Ladder-Anweisung] [Beispiel einer Ladder-Programmierung]
Ladder Sequence Control

Anwendungsbeispiele für ein Ladder-Sequenzprogramm

Ermöglicht die Reduzierung von Alarmsequenz-Regelschaltkreisen
Das Ladder-Sequenzprogramm ist serienmäßig in UT-Advanced-Geräten enthalten. Die Ladder-Sequenzfunktion ermöglicht es, periphere Geräte wie Relais zu überwachen und zu regeln und so Kosten zu senken.

[Konventionell]
Die Alarmaktion wurde durch einen Sequenzregelkreis (Relais, Timer etc.) außerhalb des Reglers erstellt.

[UT Advanced]
Die Ladder-Sequenzfunktion wird durch ein Ladder-Sequenzprogramm in dem UT-Advanced-Gerät erstellt. Dies ermöglicht es, Kosten zu senken.

Alarm Sequence Control Circuits can be Reduced

Example: Alarm annunciator

Die Auslastung des Host-Systems wird reduziert.

[Konventionell]
Action
Das Host-System (SPS etc.) erfasste und berechnete verschiedene Arten analoger Daten. Ein Feld-Regler verarbeitete die Ergebnisse zur Regelung über einen Befehl.

[UT Advanced]
Merit
Das UT-Advanced-Gerät ermöglicht es mit bis zu 4 analogen Eingängen*, verschiedene Arten analoger Daten direkt im Regler zu erfassen und durch das Ladder-Programm zu berechnen. Dies reduziert die Systementwicklungslast des Hosts. Aktion: Das Host-System (SPS etc.) erfasste und berechnete verschiedene Arten analoger Daten. Ein Feld-Regler verarbeitete die Ergebnisse zur Regelung über einen Befehl.
* Im Fall des UT55A


Host System Load is Reduced

Universaleingang/-ausgang
Wählen Sie Eingangs- und Ausgangsarten über die Konfiguration aus.

Universaleingang

Wählen Sie zwischen TC, RTD, mV/Gleichstromspannung und Gleichstrom.
(Gleichstromeingang: Kein Shunt-Widerstand erforderlich)

Universal InputDer Benutzer kann die Eingangsart und den Eingangsbereich über die Frontblende oder die LL50A-Parametereinstellungssoftware auswählen.

  • ±0,1 % Anzeigegenauigkeit.
  • Verbinden Sie bis zu zwei 2-Kabel-Transmitter gleichzeitig.

Alle Instrumente haben eine 15-V-Schleifenspannungsversorgung (15 V LPS) für einen Transmitter. Darüber hinaus ist eine 24-V-LPS gleichzeitig optional für einige Instrumente verfügbar.

Universal Input

Universalausgang

Der Benutzer kann zwischen Relais, Spannungsimpuls und Stromausgängen wählen.

  • Relaisausgang: EIN/AUS-Regelung, zeitabhängige PID-Regelung
  • Spannungsimpulsausgang: zeitabhängige PID-Regelung
  • Stromausgang: kontinuierliche PID-Regelung

Die Heiz-/Kühlregelung verfügt über zwei Sätze Universalausgänge.

  • Jede Kombination aus Relais-, Impuls- und Stromausgängen ist verfügbar.

Regeln Sie ein Servoventil mit dem positionsabhängigen PID an.

  • Die positionsabhängige PID-Regelungsfunktion verfügt über zwei Sätze an Relaisausgängen für die direkte/umgekehrte Drehung von Servoventilen.
  • Darüber hinaus ist ein Schleifdrahteingang zur Rückmeldung der Ventilposition verfügbar.

Selbsteinstellungsfunktion (AT, Auto-tuning)

Die folgenden Bedingungen können eingestellt werden, um die Genauigkeit der Berechnung der PID-Konstanten über die AT-Funktion zu erhöhen.

  1. Zwei Arten von Algorithmen zur Berechnung der PID-Konstanten stehen zur Auswahl.
    Normal: schnell steigende PID-Konstante
    Stabil: langsam steigende PID-Konstante
  2. Sie können obere und untere Ausgangsgrenzwerte einzeln während der AT-Laufzeit für Regelungsausgangswerte einstellen.

Fuzzy-Logic

SUPER-Funktion unterdrückt Wertüberschreitungen

Die bewährte SUPER-Funktion nutzt eine integrierte Bedienererfahrungs- und Fuzzy-Theorie für eine präzise Regelung und um Wertüberschreitungen zu unterdrücken.

SUPER Function Suppresses Overshoot
 

SUPER2-Funktion unterdrückt Pendelung

Die neue SUPER2-Funktion nutzt eine integrierte Bedienererfahrungs- und Kontrolltheorie für eine präzise Regelung und um Pendelung zu unterdrücken.

SUPER2 Function Suppresses Hunting

Parametereinstellungssoftware LL50A

Parametereinstellungs-/Programmmustererstellungsfunktion

Benutzer können Parameter zur Regelung der Regler-Funktionen ganz einfach einstellen: Regler-Bauart, Regler-Modus (einschleifige Regelung, Kaskadenregelung, Schleifenregelung mit PV-Umschaltung etc.), universelle Eingang/Ausgang-Funktionen, Konfigurationsparameter und weitere Parameter. Darüber hinaus können Sie so Programmmuster erstellen.

Parameter setting functions

Feineinstellfunktion

Wird zum Einstellen der PID-Parameter eines Reglers verwendet. Zeigt den gemessenen Eingangswert, den Einstellwert und den Regelungsausgangswert als Trenddiagramm auf einem PC-Monitor an und ermöglicht die Änderung von PID-Parametern, AUTO/MAN-Umschaltung, die Änderung des Regelausgangs im manuellen Betrieb etc.

Tuning function

Ladder-Entwicklungsfunktion

Sie können Ladder-Sequenzprogramme erstellen und Ladder-Programme überwachen.

Ladder Building functions

Netzwerkprofil-Erstellungsfunktion

Mit dieser Funktion können Sie ein elektronisches Gerätedatenblatt für offene Netzwerke erstellen.

Über busbasiertes USB-Kabel

Sie können diese Funktion nutzen, um Parameter und Ladder-Programme einzustellen, wenn der Regler nicht mit Strom versorgt wird.

Via Bus Powered USB Cable

Über Ethernetkommunikationsanschluss

Via Ethernet Communication Connector

Über eigenen Adapter

Via Dedicated AdapterKann bei Anschluss an das Regelpult verwendet werden.

  • Anwendbare Temperaturregler: UT75A, UT55A/UT52A, UT35A/UT32A, UP55A/UP35A/UP32A, UM33A

Über RS-485-Kommunikationsanschlüsse

Via RS-485 Communication Terminals

Einfachheit

Helles und leicht lesbares aktives Farb-LCD-Display

Bright & Easy to Read Active Color LCD Display

Vielseitiges Farb-LCD-Display

Versatile Color LCD Display

Bedienungsanzeigen des Programm-Reglers

Soll-Wert-Anzeige Programmmusteranzeige Anzeige der verbleibenden Segmentzeit Anzeige der verbleibenden Wiederholungen
SP Display Program Pattern Display
Übersicht
Remaining Segment-time Display Remaining Repetition Display
TSP-Anzeige Programmmusteranzeige Segmentnummeranzeige  
TSP Display Program Pattern Display
Haltezeit und Auflauf
Segment Number Display  
Ereignisanzeige
Event Display

* Darüber hinaus stehen dieselben Betriebsanzeigen wie bei den UT-Modellen zur Verfügung.

Funktionen des Programm-Reglers

Schnellvorlauf des Programmbetriebs
Nutzen Sie diese Funktion, wenn Sie die Programmmustereinstellungen prüfen. Nur Segmentzeiten und Zeitereignisse können schneller sein.

Programmmuster-2-Rückübertragung
Der Regler kann Programmmuster erstellen.

Program pattern-2 retransmission

Synchronisierter Programmbetrieb
Wenn der Betrieb einer Einheit schneller voranschreitet, können Sie den Programmbetrieb über den digitalen Eingang unterbrechen, wenn zwischen Segmenten gewechselt wird. Dies ermöglicht einen synchronisierten Programmbetrieb.

Synchronized program operation

Optimale Anzeige

Optimal DisplayDie Regler -Menüs und das Layout sind an das von dem Benutzer benötigte Maß an Informationen (EASY, STD und PRO) angepasst. Wählen Sie die einfache Konfiguration, wenn Sie nur eine einfache Temperatur- oder Füllstandsregelung benötigen. Auch sehr anspruchsvolle Anwendungen sind kein Problem für UT Advanced. Wählen Sie einfach die PRO-Einstellung und nutzen Sie die zusätzliche Funktionalität in diesem Modus. Erstellen Sie intelligente Anwendungen in der PRO-Einstellung und wechseln Sie anschließend in die einfache Einstellung, in der Sie von den Bedienern nicht benötigte Funktionen sperren können.

Aktives Farb-LCD-Display

Mit dem aktiven Farb-Display von Yokogawa können Sie den Status Ihres Prozesses mit einem Blick erkennen.
Alarmstatus: Das aktive Farbdisplay wechselt von weiß (normal) zu rot (Alarm).
Abweichungsstatus: Farbänderungen basieren auf PV-Abweichungen von dem Einstellwert.
Benutzerdefinierte Farbe: Wählen Sie zwischen der weißen und roten Anzeige für eine konstante Ablesung.

Active Color LCD Display

Kompakte Bauweise

Mit einer Einbautiefe von 65 mm ist die Auswahl des Einbauorts weniger eingeschränkt.

Compact Design

Einfache Bedienungsübersicht, Navigationshilfe und Navigationstasten

Mit den Navigationstasten können Sie intuitiv durch die Konfigurationsmenüs des Reglers navigieren und diese einstellen. Navigationspfeile zeigen Ihnen, welche Taste Sie als nächstes drücken müssen.

Easy Operation Map, Navigation Guide and Navigation Keys

Programmierbare Funktionstasten

Programmable Function KeysWeisen Sie ganz einfach häufig verwendete Funktionen wie den Betriebswahlschalter, Start/Stopp, die Programmmusterauswahl, Fern-/lokale Regelung, Alarmsperrenaufhebung und die PID-Parameteranzeige zu. Darüber hinaus können Sie der Taste an der Frontblende die Funktion eines externen Schalters in Verbindung mit einem Ladder-Sequenzprogramm zuweisen.

Text-Scrollfunktion

Scrolling Text


Das UT Advanced bietet eine Text-Scrollfunktion, die alle geänderten Parameter auflistet. Sie können genau erkennen, welche Parameter angezeigt werden. Die Text-Scrollfunktion lässt sich deaktivieren.

Unterstützt mehrere Sprachen

Multiple language support

Das UT Advanced unterstützt mehrere Sprachen — Englisch, Spanisch, Französisch und Deutsch. So ist die Nutzung des UT Advanced durch Bediener in der lokalen Sprache kein Problem.

Benutzerdefinierbare Standardwerte

User settable default valuesSie können vom Benutzer konfigurierte Parameterwerte (SP, P, I, D, ALM1 etc.) als Standardwerte im Regler speichern. Wird ein Einstellwert eines Parameters versehentlich geändert, kann der Benutzer den ursprünglichen Wert ganz einfach wiederherstellen.

Jetzt in zwei Farben erhältlich (Weiß oder Schwarz)

Sie können jetzt die passende Farbe für Ihren Arbeitsbereich wählen: Weiß (hellgrau) oder Schwarz (helles Holzkohlegrau).

UT55A/UT52A White & Black Models

Parametereinstellung

Mit der Parametereinstellungssoftware LL50A (separat erhältlich) wird das Einstellen von Parametern zum Kinderspiel.

Parameter Setting

Meldungsfunktion

Durch die Meldungsfunktion und indem Sie den Kontakteingang ein-/ausschalten, können Sie die zuvor aufgezeichnete Meldung durch Unterbrechung auf dem PV-Display anzeigen. Die Meldung wird durch die LL50A-Parametereinstellungssoftware aufgezeichnet. Meldungen sind auf 20 alphanumerische Zeichen begrenzt. Sie können bis zu vier Meldungen aufzeichnen.

Message Function

Schnelleinstellungsfunktion

Diese Funktion bietet die Möglichkeit, die für den Betrieb notwendigen Mindestparameter einzustellen.

Sicherheitsfunktion

Durch die Passwortfunktion können Sie unbeabsichtigte Änderungen der Parametereinstellungen verhindern. Wenn Sie ein Passwort festlegen, wird dieses bei jedem Wechsel zur Einstellungsanzeige für Einrichtparameter gefordert. Nach Prüfung des Passworts können Sie zu der Einstellungsanzeige für Einrichtparameter wechseln.

Netzwerkbetrieb

Kommunikationsfunktionen

Sie erhalten eine einfache und unkomplizierte Netzwerkverbindung!
Eine integrierte Funktion des Reglers macht einen Wandler überflüssig und erleichtert die Verkabelung.

Communication Functions

Modbus/TCP

Der Regler kann sich über das Modbus-TCP/IP Protokoll mit jedem Ethernet-Netzwerk verbinden und Daten mit Computern oder Geräten in diesem Netzwerk austauschen.

  • Regelungsgeräte lassen sich ganz einfach in eine Anwendung integrieren.
  • Funktioniert mit jeder mit Modbus-TCP/IP-kompatiblen Software.
  • Unterstützt die Modbus-Funktionscodes 03, 06, 08 & 16.
  • RS-485-Modbus-Geräte können durch die Gateway-Funktion über Ethernet kommunizieren.
  • Reduzierte Arbeitskosten im Hinblick auf die Verkabelung und Einrichtung des Kommunikationsnetzwerks.
  • Physische Ebene: 10 BASE-T/100 BASE-TX
  • Maximale Anzahl der Verbindungen: 2


Modbus / TCP

Modbus/RTU

Das DX Advanced kann die Daten des UT Advanced (Slave-Geräte) über
die Modbus-RTU-Funktion anzeigen und speichern.

Modbus / RTU

Offenes Netzwerk (PROFIBUS-DP, CC-Link, DeviceNet)

Eingebettete offene Netzwerke bieten eine direkte Verbindung zu den SPS.

  • Liest Daten von UT-Advanced-Geräten aus
  • Schreibt Parametereinstellwerte auf das UT Advanced

Beispiel:

PC-Link

Peer to Peer

Sie können mithilfe des Ladder-Sequenzprogramms analoge Daten und Statusdaten zwischen kommunikationsfähigen UT-Advanced-Geräten austauschen.

Beispiel: Ein UT-Advanced-Gerät, bei dem ein Fehler auftritt, sendet Daten an ein anderes UT-Advanced-Gerät, um es diesem zu ermöglichen, in den manuellen Betrieb zu wechseln und so das gesamte System in einen sicheren Modus zu schalten. In einem solchen Fall kann der Sicherheitsmechanismus in das UT-Advanced-Gerät integriert werden und ist nicht auf dem Host-System erforderlich.

Peer to Peer

Koordinierter Betrieb

Im koordinierten Betrieb werden ein einzelner UT-Advanced-Temperaturregler als Führungsregler und mehrere UT-Advanced-Regler oder andere UT-Advanced-Regler mit digitaler Anzeige als Folgeregler verwendet.

Die Funktion der Folgeregler richtet sich nach den Aktionen des Führungsreglers.

Coordinated Operation

PC-Link

Ein Protokoll für die Kommunikation mit einem allgemeinen PC oder einem Link-Modul der UT-Advanced-Serie und einem seriellen FA-M3R-Kommunikationsmodul.

PC-Link

Zuverlässigkeit

Zuverlässige 3-Jahres-Garantie*1

3 year warranty

Unterstützt durch die von Yokogawa über viele Jahre kultivierte hohe Zuverlässigkeit und Qualität.

RoHS/WEEE-konform

Die Entsorgung von UT-Advanced-Geräten ist umweltfreundlich.

Staub- und spritzwassergeschützte Frontblende (NEMA4*2 /IP66)

Dank der abwaschbaren Bedienkonsolen können UT-Advanced-Geräte auch in der lebensmittelverarbeitenden Industrie eingesetzt werden.

Reliability

  1. Die 3-Jahres-Garantie gilt für 36 Monate nach Lieferung ab Werk.
  2. Nur Hose-Down-Test.

Technische Daten

POSTEN UT55A UT52A
PV-Eingang Eingangstyp 1 Universaleingang (TC, RTD, mV, V, mA)
Anzeigegenauigkeit ±0,1% von SE
Kontrollscandauer   50, 100, 200 msek
PV/SP-Datenanzeige   5-stellige Balkendiagramm-LCD-Anzeige mit 14 Segmenten
Regelausgänge (MV) Typ Relais, Spannungsimpuls, Strom
Algorithmus EIN/AUS, PID (kontinuierlich, zeitanteilig), Heizen/Kühlen, positionsabhängig
Digitale Eingänge Anzahl 3 (Std) 9 (Max) 3 (Std) 5 (Max)
Typ SP Nr. Change, PID Nr. Change, A/M Change etc.
Digitale Ausgänge Anzahl 3 (Std) 18 (Max) 3 (Std) 5 (Max)
Funktion Ist-Wert hoch, Ist-Wert niedrig, Dev hoch etc.
Stromübertragungseingang (optional) Anzahl 2
Rückübertragung Anzahl 1
Typ Ist-Wert, Soll-Wert, Stellgröße etc.
Fernbetriebseingang (aux.) (optional) Anzahl 1 oder 3 1
Typ 1 bis 5 V etc.
Nur 1 Eingang kann in einen Universaleingang geändert werden, wenn die /DR-Option angegeben wird
Spannungsversorgung (LPS) (optional) Anzahl 1
Spannung 21,6 bis 28,0 V DC
Kommunikation (optional) Anzahl 1 oder 2 1
Typ RS-485, Ethernet, PROFIBUS-DP, CC-Link, DeviceNet RS-485
Weitere Spezifikationen Spannungsversorgung 100 bis 240 V AC (+10 %, –15 %) oder 24 V AC/DC (+10 %, –15 %) (optional)
Stromverbrauch Max. 18 VA Max. 15 VA
Gewicht Max. 0,5 kg

Vergleichstabelle (UT75A/UT55A/UT52A/UT35A/UT32A)

  UT75A UT55A UT52A UT35A UT32A
Modell UT75A UT55A UT52A UT35A UT32A
Größe 1/4 DIN    
1/8 DIN      
Tiefe ab Blendenoberfläche (mm) 65 65 65 65 65
Anzahl der Regelkreise Standard (maximal) 1(2) 1 1 1 1
Regler Abtastrate (msek) Auswahl 50/100/200 Auswahl 50/100/200 Auswahl 50/100/200 200 200
Anzeigefunktion Anzahl der Ist-Wert-Anzeigeziffern 5 5 5 5 5
Aktive Farb-Ist-Wert-Anzeigefunktion
Guide-Scroll-Anzeigefunktion
Meldungsanzeigefunktion
Balkendiagrammanzeige (Anzahl) ✓(2) ✓(2) ✓(2) ✓(1) ✓(1)
Anzeigegenauigkeit des Ist-Wert-Eingangs (% von SE) 0,1 0,1 0,1 0,1 0,1
Ist-Wert-Eingangstyp TC
RTD (3 Kabel)
RTD (4 Kabel)    
mV, V
mA
Anzahl der analogen Eingänge Standard (maximal) 1(4) 1(4) 1(2) 1 1
Anzahl der Soll-Werte (PID) Maximal 20(16) 8 8 4 4
Anzahl der Regelmodi Maximal 9 8 8 1 1
Anzahl der Regelungsarten Maximal 8 8 8 5 5
Regelausgang Typ Relaiskontaktausgang, Spannungsimpulsausgang, Stromausgang
Algorithmus EIN/AUS
PID (kontinuierlich, zeitanteilig)
Positionsabhängig
Heizen/Kühlen
Anzahl der analogen Ausgänge Standard (maximal) 2(3) 2(3) 2(3) 2 2
Anzahl der digitalen Eingänge Standard (maximal) 3(8) 3(9) 3(5) 2(7) 2(4)
Anzahl der Alarme   8 8 8 4 4
Anzahl der digitalen Ausgänge Standard (maximal) 3(8) 3(18) 3(5) 3(8) 3(5)
Kommunikation RS-485-Kommunikation (maximal) ✓(2) ✓(2) ✓(1) ✓(1) ✓(1)
Ethernetkommunikation    
Offenes Netzwerk (CC-Link/PROFIBUS-DP/DeviceNet)    
Verschiedene Funktionen Schnelleinstellungsfunktion
Trennungsberechnungs-Ausgabefunktion    
Quotienten- und Quadratwurzelextraktions-Funktion    
Fern-Soll-Wert-Funktion    
24-V-Gleichspannungsversorgung  
Heizstörungsalarmfunktion  
(Standardausführung)

(Standardausführung)

(Standard-
ausführung oder
Heiz-/
Kühlausführung)

(Standard
ausführung oder
Heiz-/
Kühlausführung)
Ladder-Sequenzfunktion (maximale Schrittanzahl) ✓(1000) ✓(500) ✓(500) ✓(300) ✓(300)
Weitere Spezifikationen Spannungsversorgung 100 V bis 240 V Wechselstrom
Wechselstrom/Gleichstrom 24 V
Staub- und Wasserschutzgrad der Frontblende NEMA4 *1 (IP66) NEMA4 *1 (IP66) NEMA4 *1 (IP66) NEMA4 *1 (IP66) NEMA4 *1 (IP66)
Konfigurationstool Über Light-Loader-Kommunikation
Über Wartungsanschluss
Kommunikation
Über RS-485/Ethernet-
Kommunikation
✓/✓ ✓/✓ ✓/- ✓/✓ ✓/-

Die obige Tabelle enthält ausschließlich Spezifikationen der Standardmodelle.
* 1: Nur Hose-Down-Test.

Eingangsbereich

Eingangstyp  
TC K, J, T, B, S, R, N, E, L, U, W
PL-2, PR20-40, W97Re3-W75Re25
RTD JPt100, Pt100
Gleichspannung 0,4 bis 2,0 V, 1,0 bis 5,0 V, 0,0 bis 2,0 V, 0 bis 10 V, -10 bis 20 mV, 0 bis 100 mV
Gleichstrom 4 bis 20 mA, 0 bis 20 mA

Publikationen

Übersicht:

Mercian uses the Part 11-compliant DX200P Paperless Recorder in its pharmaceutical manufacturing works.

Übersicht:

The Japan Steel Works, LTD., Muroran Plant uses the Control and Measurement Station CX2000, UP series program controllers, and UT series digital indicating controllers for operation of its heat treating furnaces.

Industrien:
Übersicht:

Kyushu Mitsui Aluminium uses the UPM100 Power Monitor for its overall factory operations, and the DX1000 Paperless Recorder for its high-purity aluminum refining furnaces.

Industrien:
Applikations-beschreibungen
Übersicht:

The UT55A can come with up to 8 alarm outputs that can control the fans. Ladder sequencing is build in, allowing you to use a timer or other such function to set up a time delay on each output.

Übersicht:

The UTAdvanced Digital Indicating Controller comes standard with ladder sequence function. The ladder sequence function can handle measured and computed values from the controller. Using this function, the UTAdvanced converts outputs from other controllers such as YS1500 to time proportioning outputs.

Applikations-beschreibungen
Übersicht:

UTAdvanced Digital Indicating Controllers come standard with ladder sequence functions in ladder programs, some of which can process data (measured and computed values). This is an example of applying those ladder programs to create a ratio station.

Übersicht:

This introduces a system that uses Ethernet communications to acquire measured values, target values, and control output values from a controller installed on site into a PLC at high speed (ten units' worth within one second).

Übersicht:

Load devices are sometimes used when evaluating (measuring) DUT performance. Depending on the parameter being evaluated, multiple controllers can be employed to control the performance of the load device, but there are also times when the load device uses only one actuator. 

Übersicht:

The UTAdvanced Digital Indicating Controller comes standard with a ladder sequence function. By using the Ladder Sequence function, you can eliminate relays and other peripherals to cut down on costs.

Übersicht:

The UTAdvanced ladder function can be used to run programs. You can also incorporate the "guarantee soak" that is required for quenching and other processes on metal parts.

Übersicht:

In the plants of food and beverage manufacturers, there are times when monitoring and recording of production equipment is necessary inside clean rooms. This is an introduction to monitoring and recording in clean rooms using paperless recorders.

Übersicht:

Environmental testing equipment (rooms) is key to checking ambient temperature and humidity in environmental worthiness tests for a variety of products (refrigerators, air conditioners, automobiles, etc.), and controllers for such equipment are also widely used.

Übersicht:

Continuous technology improvement is ongoing in the pulp & paper industry to obtain the best possible performance. The improved plant performance translates to the higher quality improvement and lower cost, and simultaneously environmental friendly plant operation.

Industrien:
Normally it is set so that only the PV value is displayed, therefore turn OFF keylock (KLOC) parameters U.PV, U.RSP, U.AI2, and U.AI4.
Can I set any sample PI control time?
(ns-faq-ut-2018-setting)
It can be specified using the sample PI sample time (STM) and sample PI control time width (SWD). This is in the tuning parameters of the operation parameters.
When the input switches, the controller tracks the PV and suppresses sudden control output changes (bumpless).
Yes, you can use it for remote (aux analog) input (RSP, AIN2, AIN4), control output (OUT, OUT2), transmission output (RET), and other things depending on the parameter settings.
I want to use 2 communication systems.
(ns-faq-ut-2085-select)
You can install 1 system from Ethernet/CC-Link/DeviceNet/PROFIBUS-DP/RS-485 on the UT75A, UT55A, UP55A, plus an additional system of RS-485. Specify these when ordering.
Yes. The communication protocol is the same, but note the difference below. You can also install two systems for use with separate protocols. The maximum speed of RS485 communication using the 2nd digit of the specification code is 19.2 kbps. The UT5...
Check whether the input on the primary loop is normal.If the input is abnormal, the unit won't switch to cascade mode.
The following are the weights of the main models: UT55A-000-00-00 Approx. 375 g UT55A-010-00-00 Approx. 435 g UT52A-000-00-00 Approx. 245 g UT52A-010-00-00 Approx. 265 g UT55A-200-01-00 Approx. 390 g UT55A-030-01-00 Approx. 390 g ...
First, set the secondary controller to AUTO operation (CAS goes out), then auto-tune that controller. Next, place it in the cascade state (CAS lights), then auto-tune the primary controller.
If you won't use the OUT and OUT2 terminal relay contacts for control output or some other purpose, you can use these models. UT55A heating/cooling model, UT57A 2 loop model For a program controller, the UP55A heating/cooling model   ...
Yes. Perform correction on A.BS of each input item.
Yes, by using the following alarm types. Analog input PV upper-limit alarm Analog input PV lower-limit alarm Analog input RSP upper-limit alarm Analog input RSP lower-limit alarm Analog input AIN2 upper-limit alarm Analog input AIN2 lower-lim...
This is supported on the UT75A, UT55A, UT52A, UP55A, and UM33A by using the 10-segment linearizer function.
Try the broken line function. That function comes with the UT52A, UT55A, UT75A, UP55A, and UM33A.
Yes, the UT75A + LL50A setting software (sold separately) can handle that.
There are three models: the UT75A and UT55A Digital Indicating Controllers, and the UP55A Programmable Controller.
On the cascade primary controller, if there is no secondary SP information, when you switch from AUTO to cascade on the cascade secondary controller, the secondary settings change abruptly, so control is interrupted. To avoid this, in advance, send t...
Can I set up 4 alarm relay outputs?
(ns-faq-ut-2016-setting)
If you don't need to use the control relay output, you can use it as an alarm relay output. Adding that to the standard-equipped 3 alarm relay outputs gives you 4 outputs.
The Ethernet setting switch is designed to enable Ethernet related parameter settings. Setting the parameter to ENTRY "1" enables the parity, IP address, subnet mask, default gateway, and port number settings. When you set this parameter to...
This means that each unit can be accessed via Ethernet from up to 2 locations at once.
As for individually writing parameters via CC-Link, changing OUT area values constitutes a write request. In your case, since the OUT area value hasn't changed from the previous value, the SP value is notoverwritten. As a fix, periodically copy t...
Use profile number 0. You can also use CCLink even if you delete the parameter assignments of Modbus slave 2 from the user profile.
RUN/STOP is set to contact input DI2 by default, and takes precedence over communication. Set S/R to OFF with DI.SL.
Reference OUT_L1 (process monitoring → process data).
If not using relay contact output for control, you can use it as a 4th alarm. This alarm would be the C contact type, therefore by connecting it to the N.C. (normal close) side you can use it as an alarm terminal. Note that when changing the basic sp...
You can change it if it is in a user profile (profile no. 0).To create a user profile, use the LL50A network profile tool.
Yes, you can use the GREEN-UTAdvanced parameter data conversion tool (available as free download). Using the LL100/LL200 parameter setting tool, save the GREEN series parameters to a file, convert them using the conversion tool, then apply the settin...
It allows communication with RS-485 compatible UTAdvanced series instruments via CC-Link. It allows acquiring data from downstream controllers that do not have CC-Link communication, and writing parameters.
The output is restricted to a lower limit of 3.2 mA (-5%) and an upper limit of 20.8 mA (105%), but only when the transmission output scale RTH and RTL settings are the same as the PV input range.
Open registers for the number of proprietary stations per unit. For example, if there are 3 CC-Link Ver. 1 stations are occupied, the bit area occupies 96 bits per station and a word area of 12 words per station. If the refresh device of the word are...
If a control relay output (C contact) is unused, you can use it for alarms.
See the UTAdvanced Series Communication Interface (RS-485, Ethernet) User's Manual.
No, a UT100 series instrument cannot connect. Only other UTAdvanced series instruments can connect.
The alarm setting values from local are carried over.
You can do this by assigning a user function key Fn, F1, or F2* (within the KEY setup parameter). * Depending on the model (UT75A, UT55A, UT52A, UT35A, UT32A)
If you connect a shunt resistance to the input terminal of the receiving side meter, you can input it as voltage. For example, if you connect a 250 Ω shunt resistance to 4–20 mA output, it's 1–5 V. Make the resistor, including t...
Proportional band P has data of up to 1 decimal point. By contrast, communication data has no decimal point. If you want to write 100.0% to P, send 1000. For differential and integral time, the data has no decimal point.
b.out indicates a burnout on the measurement input. It appears when measurement input wiring is disconnected. Check the sensor and wiring.
Yes. Data in D register number D2005 is the valve opening value. Note that with a position proportional controller, D2006 is the PID computed value.
BR is the communication speed for CC-Link. BPS is the communication speed for the Modbus master function (RS485).
When writing individual parameters via CC-Link communication, if the data values to write are not different from the existing ones, overwriting of the values does not occur. If you write all parameters by individual communication address and the valu...
When the writing flag (RX1) is ON, the next write process can't proceed. Make sure the writing flag (RX1) is OFF before performing a write process.
If outside of the parameter setting range, data is not written.
No. Only the conventional CC-Link Ver. 1.1 or 2.0 standards are supported.
Autotuning is performed when you turn AT_L1 in the OUT area to ON (= set to 1). Please make sure that AT_L1 in the OUT area turns OFF (= set to 0) after autotuning is finished.
Communication itself is available in either Remote or Local mode. Switching to Remote mode is for overwriting r.SP from an external device.
Yes. Software for converting your existing controller parameter data for use with the UTAdvanced series is available for download free of charge. GREEN to UTAdvanced Conversion Tool *Log-in Required ...
You can use the conversion tool. You don’t have to do anything after you create it. The steps are as follows: Perform the Green conversion using the conversion tool. Write the converted file to the UTA (with the CC-Link option) main unit. ...
Use a current generator with a SINK function (transmitter simulation).
The display is blank if you turn ON the power while a a dedicated LL50A cable is plugged into the maintenance port. Try removing the cable and restarting.
Assignment settings are not necessary. The heater break alarm output has a dedicated output terminal.
I can't find a parameter I want to set.
(ns-faq-ut-2001-setting)
Please see the parameter map for your specific model. UTAdvanced Series Parameter Maps and Lists
In the case of the difference lower limit alarm, the alarm setting is a negative value. For example, you need to set it to "-5°C."
Yes. Use a UT link module for the FA-M3, and use PC link communications (RS-485) for the temperature controller communication protocol selection.
Program changes for reading PV and OUT, writing SP, and other basic parameters are not necessary. There are registers and relays that support the GREEN series. For details see the UTAdvanced series communication interface (RS-485, Ethernet) user'...
Generally you should create programs in "user ladder" mode. If needed, you can rewrite the input ladder and output ladder portions.
The DATA register uses a 4-byte floating point number, therefore it displays a lot of digits. Try using the K or P registers, since they handle 2-byte integer data.
Can I use analog input in computations?
(ns-faq-ut-2032-program)
You can use it in ladder programs. On the UT55A, you can acquire up to 4 analog inputs.
Variable parameters P01-P10 can be rewritten via communication. You'll need to use the variable parameters as constants.
On the LL50A, change the system data's ladder sequence function from USE to DON'T USE. If not using the LL50A, initialize the main unit.
Yes. Use the PON flag on contact B.
It won't start while the system data or parameter setting screen is displayed. Close those screens and restart.
Check the operation of the program on the LL50A ladder program monitor.
The comparison commands of the digital indicating controllers (UT55A/UT52A/UT35A/UT32A) and program controllers (UP55A/UP35A) compare integers (rounded to the nearest decimal). If making comparisons that include decimals, first multiply the necessary...
For contacts that have duplicated functions, it is necessary to turn them OFF on the setup parameter side.
Please see the document below. It is an example of wiring and settings for pH control using the Quick Setup function. Affected models: Standard UT52A/UT55A models (if there are 2 types of chemicals, select the heating/cooling model) Setup procedure,...
Please see the document below. It is an example of wiring and settings for controlling electric furnace temperature with a thyristor using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Furnace Temperature with...
Please see the document below. It is an example of wiring and settings for controlling electric furnace temperature with solid state relays using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Furnace Temperatu...
Please see the document below. It is an example of wiring and settings to control flow with inverters using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Flow with Inverters)" ...
Please see the document below. It is an example of wiring and settings for tank level ON/OFF control using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Tank Level ON-OFF)" ...
Please see the document below. It is an example of wiring and settings for tank level proportional control using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Tank Level Proportion)" ...
Please see the document below. It is an example of wiring and settings for tank pressure control using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Tank Pressure)" ...
Yes, if using a UTAdvanced series instrument with the RS-485 communication option. Set the RS-485 protocol on the main unit to 8 (MBRTU: Modbus RTU). The initial value is 8. Select RS-485 in the LL50A communication execution screen, and make the comm...
If the LL50A's display setting is not PRO, some parameters won't display. Change the LL50A's display parameter as follows: Display > Parameter > Display level > Professional. The LL50A's display level must be set separately f...
You can display and acquire PV, SP, and OUT values as trend data. The trend data you acquire can be saved as a CSV file.
Yes. Use the SCAL ladder program command.
It is 1/20000. That is equivalent to approximately 14.5 bits.
Please see the document below. It is an example of wiring and settings for tank temperature control using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Tank Temperature)" ...
Please see the document below. It is an example of wiring and settings for controlling furnace temperature with a motorized valve using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Furnace Temperature with a ...
Please see the document below. It is an example of wiring and settings for controlling heat exchanger temperature using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Heat Exchange Temperature)" ...
Yes. The SP ramp up (UPR)/SP ramp down (DNR) function supports changing the SP value with the UT55A front panel buttons or remotely.
If you register the A1 and A2 parameters (for setting alarms 1 and 2) to the select screen, you can display the alarm 1 and 2 settings simply by pressing the DISPLAY key repeatedly. Set the CS1 and CS2 select screen parameters to "2504" and...
Yes, the output signal can be reversed. In the setup parameter OUT menu, set the OU.A parameter to "20–4."
How can I enter initial settings?
(ns-faq-ut-2064-setting)
Please see an operation guide. Controller operation guides are available for standard and detailed models. (Ex.: UT55A-000-01-00 is a standard model, and UT55A-NNN-01-AN is an detailed model). Note that you can refer to the user's manual for any ...
If OVER is displayed, the PV value will be 105% of the measurement range. The control output will be the result that is calculated using this PV value. On a -OVER, the PV value is calculated as -5% of the measurement range.
The controller's operation may be set to START/MAN. Check the controller operation indicator on the front panel.
There might be breakage in a line. Check input wiring and sensors.If the input is restored, B.OUT will be cleared automatically.
(1) Check the wiring: In MAN mode, set OUT display. Use the UP and DOWN keys to confirm operation of the control valve, and that the OUT value changes. The UP key operates the normal rotation side relay, and the DOWN key operates the reverse rotation...
Is a terminal cover included?
(ns-faq-ut-2088-select)
The UT52A, UT55A, UP55A, and UT75A come standard with terminal covers. For the UT32A, UT35A, UP35A, UP32A, and UM33A, specify the /CV option when order on or after May 31, 2015. They are also sold separately. Models: UTAP001UT75A, UT55A, UT35A, UP55A...
In this case, 20 mA is the minimum value of PV input, and 4 mA is the maximum. In the setup parameter PV menu, set RH=4.00 and RL=20.00 (the input range maximum and minimum values). For the PV input scale max, min, and decimal place, set SH=0, SL=-10...
Per the metering law, in Japan you can only use °C. For customers who require overseas-specification products that can display Fahrenheit for embedding in a device exported outside of Japan, please contact your dealer or Yokogawa representative. ...
The green numbers in the upper left part of the SP display are the SP numbers. If you register PID numbers in the select screen, you can display them in the SP display area (in orange). Register PIDN_L1_1 under Setup parameters > CSEL > CS1. ...
We have the UT52A/UT32A/UP32A in the UTAdvanced series. For an indicator with alarms, we have the 96 x 48 sized UM33A.
Check the following. Is the control type (CNT) ON/OFF, or 2 position 2 stage control?--> If so, change it to something other than that. Is the STOP lamp lit? --> Start operation (RUN). Is the MAN lamp lit? --> Set it to AUTO.   ...
Check the operation mode and communication protocol. If the operation mode is Remote (REM lights) and it's set to coordinated (PSL=CO-S), an error will occur if there is no wiring.
The UT's voltage pulse specifications are: ON voltage 12 VDC or more; load resistance 600 Ω or more; ON voltage 0.1 VDC or less. For example, in the case of the Omron G3PH (operating voltage DC4-30 V, input current 5 mA or less), up to 4 un...
You can switch the output at about ±0.25% of the input range relative to the set point.
At the time of shipment from the factory, the PID display is assigned to the Fn key on the UT front panel. If you press the Fn key, the currently used P (proportional band) is displayed. You can press the DOWN arrow key to check other items.
Try the overshoot suppression function (super function). Turn on SC: Operation parameter > TUNE > SC
The common for all GREEN series alarm relay outputs are shared. In the UTAdvanced series, each alarm relay output has its own common. If used the same way, use external wiring to connect common to common.
By factory default settings, the PID number is linked to the SP number. You can change the setting with the zone PID selection parameter (setup parameter CTL > ZON).
By factory default setting, the alarm function still works when operation is stopped (STOP). You can change the setting by using the alarm mode parameter (operation parameter ALRM > AMD).
What is the alarm standby function?
(ns-faq-ut-2111-spec)
Standby means that even when an alarm condition occurs it is ignored and the alarm stays off until the alarm condition ends. When the signal enters a non-alarm region, standby mode ends. Standby works in the following situation. When powering on ...
They are set with the same industrial quantities as the input units.
Yes, as a percentage of the PV input range span or output span.
For communication errors, the left side decimal point of the symbol display on the main unit blinks. If the SD or RD indicators light on upstream devices, check whether both are blinking.
You can specify PID parameter groups for each SP number. Each PID parameter group includes PID, output limiter, hysteresis, and other items.
For controllers, the status detection minimum hold time is the control interval + 50 ms. Also, for indicating alarms, it's the input sampling interval + 50 ms.
It's time proportional PID. That means that in addition to relay output, it can support TRIAC and voltage output. With time proportional output, control calculation result is output using the pulse width of an ON/OFF signal proportional to time. ...
The UTAdvanced series is not a CCC standard scope. Since it has acquired the GB standard, it can be used in China.
You can do this with the AMD alarm mode settings (within the ALRM operation parameter). 0: Alarm always active 1: Alarm not active during operation stop 2: Alarm not active during operation stop or manual operation
Set alarm types AL1–4 or 8 (ALRM operation parameter) to 0.0.0.00.
Yes, set parameter AL1.S (AL1 function select) to 4529.
Use a relay that supports miniscule currents. The minimum ON current of a contact input (DI) is approximately 1 mA.
By turning the OLMT output limiter switch OFF, the output limiter is disabled during manual operation.
Check whether the MAN lamp is lit. If it is, control output will not change. Press the A/M key to switch to AUTO.
Try the PV tracking function (PVT=ON). This function is useful for preventing sudden changes in the PV value. When operation starts, the PVT starts by matching SP to PV, and then uses an SP slope function (TMU, UPR, DNR) to gradually return SP to the...
Check the cycle time (CT) setting. For voltage output, try a cycle time setting of around 1 to 5 seconds.
It appears when the controller's operation mode is RUN and MAN.
Choose PC link communication (sum check enabled or none). Please also refer to the Mitsubishi Touch Panel GOT catalog and user's manual.
Perform tuning with these reference values: P=150 to 200, I=10 to 20, D=OFF.
Perform tuning with these reference values: P=150 to 200, I=10 to 20, D=OFF.
Try proportional control. Perform tuning with these reference values: P=10%, I=OFF.D=OFF, MR=0%.
Yes. Set the following: IN=1-5V, RH=1.000, RL=5.000, SDP=2, SH=0.00, SL=-10.00.
Per factory parameter settings, the EV lamp on the UT and UM is assigned to alarms, and may light depending on the measured input (PV) and setting values. Configure your EV lamp and alarm type settings to match your operating conditions.
In your ladder program, use variable register P01 and others, and write the P01 value via communication. Then do a MOV of the P01 data to the tracking input value (TRK_CTL).
“b.out” on the PV display indicates a break in the input. Check whether the signal from the sensor is getting through. Also, to narrow down the cause, you can short the input terminal of the UT itself, then if the UT's input is normal...
At DC24 V: Approximately 17 A, 1.5 ms At AC100 V: Approximately 4.5 A, 3 ms At AC240 V: Approximately 11 A, 3 ms
Per the specifications, the accuracy of type K at 0°C or higher is ±0.1% ±1 digit. The measuring range in this case is that of the selected input type, -270.0 to 1000.0. You can calculate the accuracy as follows. ±0.1% of 127...
Use the LL50A Parameter Setting Software, sold separately.
It is approximately 0.16 mA.
Check the key lock. If you see the R.SP display, in Remote mode (REM), that means SP is being set by an external (upstream, etc.) device and cannot be changed.
Yes. The read registers will be control output D7621 (OUT_OUT) and transmission output D7624 (OUT_RET). Note that these registers are for data -1500 to 31500 (equivalent to -5.0% to 105%).
Yes. The data will be -1500–31500. For the OUT terminal output, D7621(OUT_OUT) For the RET terminal output, D7624(RET_RET) For the OUT2 terminal output, D7623(OUT_OUT2L)  
Yes, by using the message function. This function assigns messages that have been registered in advance to the PV value display section, and displays them based on contact input ON/OFF states. Setting example: MG1 = 4353
This function operates during P and PD control (when integral time I = OFF). The manual reset value is the output value when PV=SP.
Q: I'm connecting a UT with CC-Link communication to another downstream UT via RS485 communication (Modbus master function). However, the RS485 communication terminal of the UT with CC-Link communication is a 2-wire system, and that of the other ...
Make the UP the parent station of two UT child stations and run the coordinated communication.
Yes. Set the DR (direct/reverse operation switching) parameter of the PID item to DIR (direct operation).
When you turn ON the power, it shows up on the self-diagnostic screen that appears for a few seconds. The 3-digit number in the SP display section is the basic suffix code. (Ex.) For the UT55A-210-01-00, the number "210" appears. ...
You can do this with the SET/ENT key system. Set MAN.T to ST.ET.
Select the type that is closest to the temperature range span that you are using.
You cannot apply an external voltage. You can connect either a no-voltage contact or a transistor contact.
For analog output of calculated results to the OUT terminal, set the output selection type OT to 00.00 and the transmission output type 01RS to OUT1.
For analog output of calculated results to the RET terminal, set the transmission output type RTS to OUT1.
For analog output of calculated results to the OUT2 terminal, set the first two digits of the output selection type OT to 00, and the transmission output type 02RS to OUT1.
You can do this with the pattern 2 transmission function. With the program pattern 2 transmission function, you can create and transmit program patterns at the same time, aside from program patterns used in control.
65 mm. For details, see the specifications of individual models.
Yes. Assign an I relay to the DO parameter.
Yes, by using PID switching. Generally, you set heating control to reverse action and cooling control to direct action.
Yes, as long as the total input and wiring resistance of the connected instruments is 600 Ω or less.
Do you sell terminal covers?
(ns-faq-ut-2233-other)
Yes. Model: UTAP001 Supports: UT75A, UT55A, UT35A, UP55A, UT35A Model: UTAP002 Supports: UT52A, UT32A, UP32A, UM33A
Not with parameter settings, but you can do this with a ladder program.
Not with parameter settings, but you can do this with a ladder program.
No, use 1 contact per input. If you connect multiple inputs, when you turn OFF the UT, the impedance lowers and mis-operation can result.
No, it only comes in white.
It’s from U-RD. Please purchase them from our dealers.
Recommended CT:U-RD CTL-6-S-H: CT ratio 800, measurable current range: 0.1-80.0 Arms CTL-12L-30: CT ratio 3000, measurable current range: 0.1-180.0 Arms
Turn OFF the U.PID parameter symbol in the setup parameter KLOC menu.
For a power failure of approximately 5 seconds or more, you can do this with the restart mode R.MD setting. For power failures of less than approximately 5 seconds, the control operation prior to the power failure continues. ...
You can use this with suffix codes /LP, /L1, /LCH, /L4, and /LC4. For wiring to a 2-wire transmitter, the controller is equipped with an insulated sensor power supply (21.6 to 28.0 VDC). ...
You can download these items from the Partner Portal member site *Log-in Required. You must register (free) to use Partner Portal.
The split computation output function is useful for coordinated control of multiple operating units that perform actions such as switching between warm and cold water. The characteristics of split computation output are V and parallel.

Downloads

Möchten Sie weitere Informationen über unsere Mitarbeiter, Technologien und Lösungen?

Kontakt

Top