UM33A

Die neue Digitalanzeige UM33A mit Alarmfunktion bietet bis zu 9 Alarmausgänge und Eingangskorrekturfunktionen (PV-Messabweichung, Polygonzug-Annäherung, Polygonzug-Messabweichung). Darüber hinaus ist optional eine Stromversorgung für den 24-V-DC-Sensor verfügbar.

Neu! UM33A-S SENCOM HMI Typ
Das UM33A-S wird an Sensoren angeschlossen, welche wiederum an einen digitalen SENCOM Smart Adapter, Modell SA11, angeschlossen sind.

Übersicht

Die neue Digitalanzeige UM33A mit Alarmfunktion bietet bis zu 9 Alarmausgänge und Eingangskorrekturfunktionen (PV-Messabweichung, Polygonzug-Annäherung, Polygonzug-Messabweichung). Darüber hinaus ist optional eine Stromversorgung für den 24-V-DC-Sensor verfügbar.

Intelligente Funktion

  • PV-Messabweichung, Polygonzug-Annäherung, Polygonzug-Messabweichung
  • Stromversorgung für 24-V-DC-Sensor verfügbar

Einfachheit

  • Einfach abzulesendes großes LCD-Farbdisplay mit 14 Segmenten
  • Textscroll-Funktion für Parameter
  • Navigationshilfe und Navigationstasten
  • Programmierbare Funktionstasten
  • Benutzerdefinierbare Standardwerte
  • Unterstützt mehrere Sprachen (Englisch, Spanisch, Französisch, Deutsch)
  • Kompakte Bauweise mit einer Tiefe von 65 mm

Netzwerkbetrieb

  • RS-485 (Modbus/RTU, Peer to Peer, koordiniert,   PC-Link,  CC-Link)
  • RS-485 (Modbus/RTU-Datenüberwachungsfunktion, Modbus/RTU-Masterfunktion) Neu →Hier klicken

Zuverlässigkeit

  • 3 Jahre Garantie*1
  • RoHS/WEEE
  • NEMA4*2/IP56-Frontblende

Anwendungssoftware

  • LL50A-Parametereinstellungssoftware mit Ladder-Programm-Entwicklungsfunktion (separat erhältlich)

*1: Die 3-Jahres-Garantie umfasst 36 Monate
*2: Nur Hose-Down-Test

Details

Technische Daten

POSTEN UM33A
PV-Eingang Eingangstyp 1 Universaleingang (TC, RTD, mV, V, mA)
Anzeigegenauigkeit ±0,1 % von SE
Kontrollscandauer   50, 100, 200 ms
PV/SP-Datenanzeige   5-stellige LCD-Anzeige mit 14 Segmenten
Digitale Eingänge Nummer 2
Typ PV-Spitze und Grenzwertrücksetzung
Digitale Ausgänge Nummer 3 (Std) 9 (Max)
Funktion PV High, PV Low, Dev High etc.
Rückübertragung Nummer 1
Typ PV
Schleifenspannungsversorgung (LPS) (optional) Nummer 1
Spannung 21,6 bis 28,0 V DC
Kommunikation (optional) Nummer 1
Typ RS-485
Sonstige Spezifikationen Spannungsversorgung 100 bis 240 V AC (+10 %, –15 %) oder 24 V AC/DC (+10 %, –15 %) (optional)
Stromverbrauch Max. 15 VA
Gewicht Max. 0,5 kg

Publikationen

Übersicht:

Taking advantage of sensors already available in your system, you can simply add VJ series signal conditioners or the UM33A Digital Indicator with Alarms to easily build a monitoring system on a PC.

Übersicht:

The UM33A Digital Indicator with Alarms is a digital panel meter with an easy-to-read white LED. Combining the features below, it can be used as a digital indicating controller for control rooms, and instrumentation panels in process automation sites.

Übersicht:

Check site conditions while monitoring temperature and humidity of the production line and storehouse.

Applikations-beschreibungen
Übersicht:
  • Effeciently controls the inlet valve and blow-off valve when the compressor starts and stops.
  • During steady operation, controls the inlet valve so that the amount of discharged compressed air becomes constant (flow control)
  • Surging: Load decreases, the amount of discharge flow and pressure drop, and a limit is exceeded, possibly destroying the compressor.
Use the Select Screen function. Up to 5 select screens can be configured. Assign parameters CS1–CS5 to Alarm1:2351 through Alarm8:2358.
Yes. Set the input range to 0-10 V. Short the input terminal (terminal no. 202-203). If you write the value to the parameter's bias (BS) item, it is reflected to the PV value. Note, the profile is overwritten so you need the LL50A.
Try the 10-segment linearizer approximation function.
PEAK and BOTM are not setting parameters. They are the maximum and minimum values of the measurement input (PV), respectively.
This is supported on the UT75A, UT55A, UT52A, UP55A, and UM33A by using the 10-segment linearizer function.
Try the broken line function. That function comes with the UT52A, UT55A, UT75A, UP55A, and UM33A.
If you register the A1 and A2 parameters (for setting alarms 1 and 2) to the select screen, you can display the alarm 1 and 2 settings simply by pressing the DISPLAY key repeatedly. Set the CS1 and CS2 select screen parameters to "2504" and...
We have the UT52A/UT32A/UP32A in the UTAdvanced series. For an indicator with alarms, we have the 96 x 48 sized UM33A.
Per factory parameter settings, the EV lamp on the UT and UM is assigned to alarms, and may light depending on the measured input (PV) and setting values. Configure your EV lamp and alarm type settings to match your operating conditions.
You can use this with suffix codes /LP, /L1, /LCH, /L4, and /LC4. For wiring to a 2-wire transmitter, the controller is equipped with an insulated sensor power supply (21.6 to 28.0 VDC). ...
As for individually writing parameters via CC-Link, changing OUT area values constitutes a write request. In your case, since the OUT area value hasn't changed from the previous value, the SP value is notoverwritten. As a fix, periodically copy t...
Use profile number 0. You can also use CCLink even if you delete the parameter assignments of Modbus slave 2 from the user profile.
RUN/STOP is set to contact input DI2 by default, and takes precedence over communication. Set S/R to OFF with DI.SL.
If not using relay contact output for control, you can use it as a 4th alarm. This alarm would be the C contact type, therefore by connecting it to the N.C. (normal close) side you can use it as an alarm terminal. Note that when changing the basic sp...
You can change it if it is in a user profile (profile no. 0).To create a user profile, use the LL50A network profile tool.
It allows communication with RS-485 compatible UTAdvanced series instruments via CC-Link. It allows acquiring data from downstream controllers that do not have CC-Link communication, and writing parameters.
The output is restricted to a lower limit of 3.2 mA (-5%) and an upper limit of 20.8 mA (105%), but only when the transmission output scale RTH and RTL settings are the same as the PV input range.
Open registers for the number of proprietary stations per unit. For example, if there are 3 CC-Link Ver. 1 stations are occupied, the bit area occupies 96 bits per station and a word area of 12 words per station. If the refresh device of the word are...
See the UTAdvanced Series Communication Interface (RS-485, Ethernet) User's Manual.
No, a UT100 series instrument cannot connect. Only other UTAdvanced series instruments can connect.
If you connect a shunt resistance to the input terminal of the receiving side meter, you can input it as voltage. For example, if you connect a 250 Ω shunt resistance to 4–20 mA output, it's 1–5 V. Make the resistor, including t...
Proportional band P has data of up to 1 decimal point. By contrast, communication data has no decimal point. If you want to write 100.0% to P, send 1000. For differential and integral time, the data has no decimal point.
b.out indicates a burnout on the measurement input. It appears when measurement input wiring is disconnected. Check the sensor and wiring.
BR is the communication speed for CC-Link. BPS is the communication speed for the Modbus master function (RS485).
When writing individual parameters via CC-Link communication, if the data values to write are not different from the existing ones, overwriting of the values does not occur. If you write all parameters by individual communication address and the valu...
When the writing flag (RX1) is ON, the next write process can't proceed. Make sure the writing flag (RX1) is OFF before performing a write process.
If outside of the parameter setting range, data is not written.
No. Only the conventional CC-Link Ver. 1.1 or 2.0 standards are supported.
Autotuning is performed when you turn AT_L1 in the OUT area to ON (= set to 1). Please make sure that AT_L1 in the OUT area turns OFF (= set to 0) after autotuning is finished.
Use a current generator with a SINK function (transmitter simulation).
Turn OFF the U.PID parameter symbol in the setup parameter KLOC menu.
The display is blank if you turn ON the power while a a dedicated LL50A cable is plugged into the maintenance port. Try removing the cable and restarting.
I can't find a parameter I want to set.
(ns-faq-ut-2001-setting)
Please see the parameter map for your specific model. UTAdvanced Series Parameter Maps and Lists
Yes. Use a UT link module for the FA-M3, and use PC link communications (RS-485) for the temperature controller communication protocol selection.
Program changes for reading PV and OUT, writing SP, and other basic parameters are not necessary. There are registers and relays that support the GREEN series. For details see the UTAdvanced series communication interface (RS-485, Ethernet) user'...
Yes, if using a UTAdvanced series instrument with the RS-485 communication option. Set the RS-485 protocol on the main unit to 8 (MBRTU: Modbus RTU). The initial value is 8. Select RS-485 in the LL50A communication execution screen, and make the comm...
If the LL50A's display setting is not PRO, some parameters won't display. Change the LL50A's display parameter as follows: Display > Parameter > Display level > Professional. The LL50A's display level must be set separately f...
You can display and acquire PV, SP, and OUT values as trend data. The trend data you acquire can be saved as a CSV file.
How can I enter initial settings?
(ns-faq-ut-2064-setting)
Please see an operation guide. Controller operation guides are available for standard and detailed models. (Ex.: UT55A-000-01-00 is a standard model, and UT55A-NNN-01-AN is an detailed model). Note that you can refer to the user's manual for any ...
There might be breakage in a line. Check input wiring and sensors.If the input is restored, B.OUT will be cleared automatically.
Is a terminal cover included?
(ns-faq-ut-2088-select)
The UT52A, UT55A, UP55A, and UT75A come standard with terminal covers. For the UT32A, UT35A, UP35A, UP32A, and UM33A, specify the /CV option when order on or after May 31, 2015. They are also sold separately. Models: UTAP001UT75A, UT55A, UT35A, UP55A...
In this case, 20 mA is the minimum value of PV input, and 4 mA is the maximum. In the setup parameter PV menu, set RH=4.00 and RL=20.00 (the input range maximum and minimum values). For the PV input scale max, min, and decimal place, set SH=0, SL=-10...
Per the metering law, in Japan you can only use °C. For customers who require overseas-specification products that can display Fahrenheit for embedding in a device exported outside of Japan, please contact your dealer or Yokogawa representative. ...
The common for all GREEN series alarm relay outputs are shared. In the UTAdvanced series, each alarm relay output has its own common. If used the same way, use external wiring to connect common to common.
What is the alarm standby function?
(ns-faq-ut-2111-spec)
Standby means that even when an alarm condition occurs it is ignored and the alarm stays off until the alarm condition ends. When the signal enters a non-alarm region, standby mode ends. Standby works in the following situation. When powering on ...
They are set with the same industrial quantities as the input units.
Yes, as a percentage of the PV input range span or output span.
For communication errors, the left side decimal point of the symbol display on the main unit blinks. If the SD or RD indicators light on upstream devices, check whether both are blinking.
For controllers, the status detection minimum hold time is the control interval + 50 ms. Also, for indicating alarms, it's the input sampling interval + 50 ms.
The UTAdvanced series is not a CCC standard scope. Since it has acquired the GB standard, it can be used in China.
Set alarm types AL1–4 or 8 (ALRM operation parameter) to 0.0.0.00.
Use a relay that supports miniscule currents. The minimum ON current of a contact input (DI) is approximately 1 mA.
Yes. Set the following: IN=1-5V, RH=1.000, RL=5.000, SDP=2, SH=0.00, SL=-10.00.
“b.out” on the PV display indicates a break in the input. Check whether the signal from the sensor is getting through. Also, to narrow down the cause, you can short the input terminal of the UT itself, then if the UT's input is normal...
At DC24 V: Approximately 17 A, 1.5 ms At AC100 V: Approximately 4.5 A, 3 ms At AC240 V: Approximately 11 A, 3 ms
Per the specifications, the accuracy of type K at 0°C or higher is ±0.1% ±1 digit. The measuring range in this case is that of the selected input type, -270.0 to 1000.0. You can calculate the accuracy as follows. ±0.1% of 127...
It is approximately 0.16 mA.
Check the key lock. If you see the R.SP display, in Remote mode (REM), that means SP is being set by an external (upstream, etc.) device and cannot be changed.
Yes. The data will be -1500–31500. For the OUT terminal output, D7621(OUT_OUT) For the RET terminal output, D7624(RET_RET) For the OUT2 terminal output, D7623(OUT_OUT2L)  
Q: I'm connecting a UT with CC-Link communication to another downstream UT via RS485 communication (Modbus master function). However, the RS485 communication terminal of the UT with CC-Link communication is a 2-wire system, and that of the other ...
When you turn ON the power, it shows up on the self-diagnostic screen that appears for a few seconds. The 3-digit number in the SP display section is the basic suffix code. (Ex.) For the UT55A-210-01-00, the number "210" appears. ...
Select the type that is closest to the temperature range span that you are using.
You cannot apply an external voltage. You can connect either a no-voltage contact or a transistor contact.
65 mm. For details, see the specifications of individual models.
Do you sell terminal covers?
(ns-faq-ut-2233-other)
Yes. Model: UTAP001 Supports: UT75A, UT55A, UT35A, UP55A, UT35A Model: UTAP002 Supports: UT52A, UT32A, UP32A, UM33A
No, use 1 contact per input. If you connect multiple inputs, when you turn OFF the UT, the impedance lowers and mis-operation can result.
No, it only comes in white.

Downloads

Möchten Sie weitere Informationen über unsere Mitarbeiter, Technologien und Lösungen?

Kontakt

Top