Flowmeters are vital to your Plant Operations – don’t neglect them

Flowmeters are vital to your Plant Operations – don’t neglect them

May 19, 2020

Flowmeter Verification via Maintenance Manager Functionalities

The human body is a remarkable piece of engineering and involves many complex processes. We work our bodies hard and are concerned with keeping it healthy. Hence, even if we work-out and look after ourselves, we still go to the doctor for regular health check-ups.

The flowmeters used in your process are themselves complex pieces of equipment, which perform vital roles. They work very hard, often operating 24 hours a day, 365 days a year. Many plants and processes cannot operate effectively without them. Flowmeters ensure dosing rates are optimised, batching and packaging are correct and provide the data for various balances around an operating plant. However, we often neglect to give our flowmeters a “health check-up”.

When to invest in a health check for flowmeters

Most of the time, people only investigate the health of a flowmeter when it has failed, or its measurement accuracy is under question. The reason for this has often been due to the verification process being complicated and costly. In the early days, to check a flowmeter required taking it out of the process and sending it away for checking and verification. In recent times, external verification became an option, which involved using external verification tools and software to check the flowmeter. This required external equipment, which often was not available for purchase by the end-user and also required skilled personnel.


Modern flowmeters feature “Maintenance Manager” functionalities, which have integrated the verification function into the device, making it both quick and simple to complete. The flowmeter’s electronics run a series of on-board tests while the flowmeter is still installed in the process piping and provide a “pass” or “fail” result once they are completed. If a flowmeter fails verification, the flowmeter will indicate the area of testing that caused the failure, allowing the user to attempt to identify the cause or to contact the manufacturer for additional support. The time to run a verification depends on the flowmeter and can take from a few minutes to around twelve minutes to complete. As the verification procedure is simple and can be performed while the flowmeter is still installed in the process piping, the flowmeter can be verified as frequently as required by each individual site.

For a magnetic flowmeter, the verification typically tests the magnetic, excitation, and calculation circuits. It should also run a thorough check of the alarms and alarm history. For remote flowmeter systems, the latest advanced flowmeters also include a cable connection check, to ensure the excitation and signal wiring between the remote flowtube and remote transmitter are correct. Modern magnetic flowmeters featuring built-in verification can run the tests in the flowmeter itself, or the tests can be done via external HART software tools. Using software enables the capability for additional verification testing of the analog and pulse outputs, insulation resistances, and electronic amplifier checks. It can then provide a hard-copy report of the verification results.

Tube Health Check



For Coriolis mass flowmeters, verification typically checks the drive, sensor, and temperature circuits as well as the hardware and software. The most advanced Coriolis flowmeters also offer an additional option for tube health checking. The measurement tubes in a Coriolis flowmeter can be damaged over a period of time due to corrosion, erosion or deposits. If the condition of the measuring tubes deteriorates, it will impact the accuracy of your flow and density measurements. The tube health check function measures the change in stiffness of the measurement tubes and compares it to an initial reference value. Coriolis flowmeters featuring built-in verification allow these tests to be performed internally or via HART communication to a software package. Reports can be provided when external software is used.

Maintenance Manager functionalities in flowmeters

Utilising “Maintenance Manager” functionalities in your flowmeters can really improve your process operations. Flowmeter verification provides you with greater confidence in the accuracy and performance of your flowmeter. It can also provide data for predictive maintenance planning to optimise timing for cleaning, re-calibration, or device replacement.

Flowmeters are vital to plant operations – don’t neglect them. Using the latest “Maintenance Manager” functionalities allows you to give them a regular health check-up and ensure they are operating correctly.

Check out the video below for further information!


By loading the video, you agree to YouTube's privacy policy.
Learn more

Load video

1 Comment so far

Jump into a conversation
    #1 Sethupathy SIVARAMAKRISHNAN 19 May, 2020, 08:48

    Verry good information on flow meter especially mass flow meter ( coriolis or MFT) the new function Maintenance Manager is appreciated and welcome. Great invention. Best wishes

    Reply this comment

Your data will be safe!Your e-mail address will not be published. Also other data will not be shared with third person.