고급형 온도 조절계 UT75A

UT75A 온도 컨트롤러는 네비게이션 키와 함께 읽기 쉬운 14 세그먼트 대형 컬러 LCD 디스플레이를 채택하여 모니터링 및 작동 기능을 크게 향상시켰습니다. 또한, 래더 시퀀스 기능도 표준으로 탑재하고 있습니다. 컨트롤러의 깊이가 짧아 공간을 절약할 수 있으며 이더넷 통신과 같은 개방형 네트워크도 지원합니다.

UT75A 온도 컨트롤러 기능

  • 최대 2 루프 제어 가능
  • 1,000 Step까지의 래더 시퀀스 용량
  • 래더 시퀀스 프로그램 구축 가능
  • SP 최대 20 개 가능
  • 오픈 네트워크 지원 (CC-Link, PROFIBUS-DP, DeviceNet)

Details

제품 세부 사양

UT75A 온도 조절계

ut75a-00.png

강화된 성능으로 다양한 어플리케이션 제어를 제공합니다. 

다양한 레시피 관리로 생산성 향상

20 조합의 레시피 전환

  • 다양한 레시피를 관리하여 생산량 늘리기
  • 16 개의 PID 값과 조합하여 품질 향상

Increasing yield by managing a variety of recipes

프로그램 패턴 운전

  • 프로그램 패턴은 1 패턴에 최대 20 세그먼트로 구성
  • 2 루프 프로그램 패턴 조작 가능

2-loop program pattern can be operated

PLC로 간단하게 레시피 전환

  • CC-Link, PROFIBUS, DeviceNet를 지원하여 PLC와 쉽게 연결 가능

엔지니어링 비용 및 주변 장치 절감

Easy to switch between recipes with a PLC

래더 프로그램 간소화

  • 수치 계산과 같은 여러줄의 래더 프로그램은 사용자 정의 래더 명령을 사용하여 한줄로 변환 할 수 있습니다.
  • 이는 래더 프로그램을 단순화하고 엔지니어링 및 유지 보수를 용이하게합니다.
  • 생성된 사용자 정의 래더 명령을 파일로 저장할 수 있습니다.
  • 파일에 저장된 사용자 정의 래더 명령은 다른 UT75A 온도 컨트롤러에서도 사용할 수 있습니다.

 

 

ut75a-04.png

외부 연산기와 시퀀스 제어 회로 (릴레이, 타이머 등) 생략 가능

  • 복잡한 입출력 보정 연산 및 경보 시퀀스 제어는 래더 프로그램으로 실현 가능합니다.
  • 배선과 기본 엔지니어링 비용을 크게 줄일 수 있습니다.
  • 2 루프 제어에서 루프 사이에 시퀀스를 만들 수 있습니다.

External calculators and sequence control circuits (relay, timer, etc.) can be reduced

프로그램을 사용하지 않고도 PLC와의 통신 가능

  • CC-Link, Profibus 및 DeviceNet 지원 (옵션)
  • 프로그램을 사용하지 않고도 PLC와의 통신이 가능하기 때문에 엔지니어링 비용이 절감됩니다.

고객의 노하우를 보호

고객의 연산식을 래더 프로그램으로 작성 가능

  • 수치 계산과 같은 여러줄의 래더 프로그램은 사용자 정의 래더 명령을 사용하여 한줄로 변환 할 수 있습니다.
  • 사용자 정의 래더 프로그램에 암호를 사용하여 안전하게 관리할 수 있습니다.
    - 고객의 노하우를 보호하기 위해 사용자 연산식을 비공개로 만들 수 있습니다.

Custom arithmetic expressions can be created using a ladder program

UT750 대체 및 개선

단일 컨트롤러로 2 루프 제어

  • 2 루프의 동기 운전 / 독립 운전이 가능
    - 운전 개시 / 정지를 동기화 또는 독립적으로 동작 할 수 있습니다.
  • 프로그램 패턴 운전 및 정치 운전의 2 루프 제어가 가능
    - 프로그램 패턴 운전 및 정치 운전을 결합하여 작동 할 수 있습니다.

2-loop control with a single controller

다양한 연산 명령과 대용량의 래더 프로그램

  • 기본 명령 15 가지, 응용 명령 111 가지
  • 래더 프로그램 용량 최대 1000 steps

A variety of arithmetic instructions and large capacity ladder programs

고급 연산 명령 사용 가능

  • 제곱근, 지수, 로그 등의 연산이 가능
  • 온도 / 습도 및 CP 연산 가능

Advanced arithmetic instructions

Downtime 단축

범용 입출력

  • 하나의 백업 컨트롤러는 다양한 유형의 센서 및 히터 / 액추에이터를 사용하여 서로 다른 제어 개체를 사용할 수 있습니다.
    -고장이나 급격한 사양 변경에 유연하게 대응할 수 있습니다.

Universal input and output

LL50A를 사용한 간단한 파라미터 설정 및 전환

  • 매개 변수는 복사하여 다른 컨트롤러에서 설정 가능
  • 조절계를 패널에 장착하기 전, 파라미터 설정 가능
  • 조절계에 전원 공급없이 파라미터 설정 가능

Simple parameter setting and transition using an LL50A

Advanced 제어

8 개의 제어 모드 내장 

제어 모드를 사용하면 쉽게 설정을 구성하고 매개 변수로 변경을 할 수 있습니다.

  • 단일 루프 제어
  • Cascade 1차측 제어 
  • Cascade 2차측 제어 
  • Cascade 제어
  • Loop control for backup
  • PV switching 제어
  • PV auto-selector 제어
  • PV-hold function 제어

8 built-in Control Mode

8 개의 제어 유형 내장

  • 8 Built-in Control TypesPID control
  • ON/OFF 제어 (히스테리시스 1 점)
  • ON/OFF 제어 (히스테리시스 2 점)
  • 2 위치, 2 레벨 제어 
  • 가열 / 냉각 제어 
  • 샘플 PI 제어
  • 일괄 PID 제어
  • 피드 포워드 제어 

위의 제어 모드와 각 모델의 제어 유형 간의 대응은 각 모델의 사양을 참조하십시오.

래더 시퀀스 제어

래더 시퀀스 제어 기능이 내장되어있어 적용 범위가 크게 늘어납니다. 이 기능은 모든 UTAdvanced 컨트롤러 (UM33A 제외)에서 표준입니다. 래더 시퀀스 제어 기능은 애플리케이션에 필요한 소형 PLC를 대체 할 수 있습니다. 시퀀스 제어와 PID 제어를 동시에 수행 할 수 있습니다.

  • 외부 기기 모니터링 및 제어
    예 : 램프, 스위치, 타이머
  • 디지털 입 / 출력 로직 기능을 쉽게 해결하십시오.
    기본 명령 유형 수 : 13
    응용 프로그램 명령 유형 수 : 73
[래더 명령의 예]        [래더 프로그래밍의 예]
Ladder Sequence Control

래더 시퀀스 프로그램의 적용 예

알람 시퀀스 제어 회로를 줄일 수 있음
래더 시퀀스 프로그램은 UTAdvanced에 표준으로 내장되어 있습니다. 
래더 시퀀스 기능은 릴레이와 같은 주변 장치를 모니터링하고 제어 할 수 있으므로 비용을 절감 할 수 있습니다.

[Conventional]

알람 동작은 컨트롤러 외부의 시퀀스 제어 회로 (릴레이, 타이머 등)에 의해 구축되었습니다.

[UTAdvanced]

경보 동작은 UTAdvanced 내부의 래더 시퀀스 프로그램에 의해 구축되므로 비용을 절감 할 수 있습니다.

Alarm Sequence Control Circuits can be Reduced

Example: Alarm annunciator

호스트 시스템의 업무 감소

[Conventional]
Action

다양한 종류의 아날로그 데이터가 호스트 시스템 (PLC 등)에 수집되어 계산되었으며, 결과는 명령을 통해 제어하기 위해 현장 컨트롤러에 의해 처리되었습니다.

[UTAdvanced]
Merit

최대 4 개의 아날로그 입력 *이있는 UTAdvanced를 사용하면 다양한 유형의 아날로그 데이터를 컨트롤러에 직접 캡처하여 래더 프로그램에서 계산할 수 있으므로 호스트의 시스템 구축로드가 줄어 듭니다. 
* UT55A의 경우

Host System Load is Reduced

범용 입력/출력
구성을 통해 입력 및 출력 유형 선택

범용 입력

TC, RTD, mV/DC 전압 및 DC 전류
(DC 전류 입력 : 션트 저항 필요 없음)

Universal Input

입력 유형 및 범위는 전면 키를 이용해 설정하거나 LL50A 매개 변수 설정 소프트웨어를 사용하여 사용자가 선택할 수 있습니다. 

  • ±0.1% 지시 정확도
  • 최대 2개의 2선식 송신기를 동시에 연결하십시오 

모든 계측기에는 송신기 용 15 V 루프 전원 공급 장치 (15 V LPS)가 있습니다.
또한 옵션 기능으로 24V LPS를 일부 계기에서 동시에 사용할 수 있습니다.

Universal Input

범용 출력

릴레이, 전압 펄스 출력 전류 출력에서 선택할 수 있습니다.

  • 릴레이 출력 : ON / OFF 제어, 시간 비례 PID 제어
  • 전압 펄스 출력 : 시간 비례 PID 제어
  • 전류 출력 : 연속 PID 제어

가열 / 냉각 제어는 각각의 출력을 범용 출력에서 선택할 수 있습니다.

  • 릴레이, 펄스 및 전류 출력의 조합을 사용할 수 있습니다.

위치 비례 PID 제어 사용으로 모터 밸브를 구동 할 수 있습니다.

  • 위치 비례 제어 출력은 모터 밸브에 정/역회전의 신호를 보내기위해 2 개의 릴레이 출력을 가지고 있습니다.
  • 모터 밸브의 개폐 위치를 피드백 하기 위한 기능을 가지고 있습니다.

오토 튜닝 (AT) 기능

AT에 의한 PID의 산출 정밀도를 높이기 위해 다음 조건을 설정할 수 있습니다.

  1. PID 정수의 산출 연산에서 두 가지 유형에서 선택할 수 있습니다.
    보통 : 상승이 빠른 PID 정수
    안정 : 상승이 느린 PID 정수
  2. AT 실행시 제어 출력 값 제한(최대 출력과 최소 출력을 설정)을 설정할 수 있습니다.

제어 알고리즘

SUPER 오버 슈트 억제 기능

"SUPER"기능은 퍼지 이론을 사용한 오버 슈트 억제 기능입니다. 오토 튜닝 기능과 함께 사용하여 다음과 같은 사례에서 효과를 발휘합니다.

SUPER Function Suppresses Overshoot

SUPER2 헌팅 억제 기능 

"SUPER2" 기능은 PID 연산 시 위상 보상을 하여 헌팅을 억제하는 기능입니다. 다음과 같은 사례에서 효과를 발휘합니다.

SUPER2 Function Suppresses Hunting

LL50A 파라미터 설정 소프트웨어

파라미터 설정 / 프로그램 패턴 작성 기능

LL50A를 이용하여 파라미터 설정 및 프로그램 패턴 생성 뿐만 아니라 데이터 관리도 쉽게 할 수 있습니다. 또한 설정한 매개 변수를 UTAdvanced에 초기 파라미터로 지정하여 등록 가능합니다. (초기화 작업은 전면 판넬 키에서도 실시 할 수 있습니다.)

Parameter setting functions

튜닝 기능

UTAdvanced의 PID 값을 최적화 할 때 사용하면 편리합니다. PID 값의 수정 뿐만 아니라 목표 설정치 (SP) 변경, 자동 / 수동 등의 모드 전환도 가능합니다. 화면에서 SP / PV / OUT 값을 모니터하면서 실행 가능하므로 간편한 튜닝 작업이 가능합니다.

Tuning function

래더 프로그램 작성 기능

래더 시퀀스 프로그램을 작성하고 래더 프로그램을 모니터링 할 수 있습니다.

Ladder Building functions

네트워크 프로파일 생성 기능

오픈 네트워크 장치 데이터 시트를 생성 할 수 있습니다.

전용 USB 케이블로 연결

PC에서 USB 케이블 전원 사용으로 조절계에 전원이 없는 상황에서 파라미터 설정 / 래더 시퀀스 프로그램 설정이 가능합니다.

Via Bus Powered USB Cable

Ethernet 통신을 통해 연결

Via Ethernet Communication Connector

전용 어댑터를 통해 연결

Via Dedicated Adapter패널에 부착된 상태에서 사용할 수 있습니다

  • 적용 가능한 모델 : UT75A, UT55A / UT52A, UT35A / UT32A, UP55A / UP35A / UP32A, UM33A

RS-485 통신을 통해 연결

Via RS-485 Communication Terminals

간단 표시 

밝고 읽기 쉬운 액티브 컬러의 LCD 디스플레이

Bright & Easy to Read Active Color LCD Display

다목적 컬러의 LCD 디스플레이

Versatile Color LCD Display

프로그램 제어기의 조작 화면  

SP 화면 프로그램 패턴 화면 남은 세그먼트 시간 화면 남은 반복횟수 화면
SP Display Program Pattern Display
overview
Remaining Segment-time Display Remaining Repetition Display
TSP 화면 프로그램 패턴 화면 세그먼트 번호 화면  
TSP Display Program Pattern Display
Soak and ramp
Segment Number Display  
이벤트 화면
Event Display

* UT와 동일하게 조작 표시가 가능합니다.

프로그램 컨트롤러의 기능

프로그램 작업의 빠르게 확인하기 기능
프로그램 패턴 설정을 확인할 때 이 기능을 사용하십시오. 세그먼트 시간 및 시간 이벤트의 시간만 빠르게 체크 가능합니다.

프로그램 패턴 2 재전송
컨트롤러는 프로그램 패턴 생성기 역할을 할 수 있습니다.

Program pattern-2 retransmission

동기식 프로그램 작동
한 유닛의 운전 진행이 더 빠르면 세그먼트 사이를 전환 할 때 디지털 입력에 의해 프로그램 작동을 강제 중지 할 수 있습니다. 따라서, 동기된 프로그램 작동을 수행할 수 있습니다.

Synchronized program operation

최적의 표시 화면

Optimal Display컨트롤러 설정 메뉴 및 레이아웃은 사용자가 요구하는 설정 레벨 (EASY, STD, PRO)에 따라 조정됩니다. 간단한 온도 설정 또는 레벨 제어 설정이 필요한 경우 EASY 모드 설정을 선택하십시오. 매우 정교한 설정은 PRO 모드 설정을 선택하고 이 모드에서 추가로 표시된 기능을 사용하기만 하면 됩니다. PRO 설정에서 프로그래밍한 다음 EASY 설정으로 다시 변경하여 운영자가 필요하지 않은 기능을 표시하지 않을 수 있습니다.

액티브 컬러 LCD 화면

Yokogawa의 액티브 컬러 화면을 사용하면 프로세스 상태를 한 눈에 즉시 알 수 있습니다.
알람 상태 : 활성 컬러 화면이 흰색(정상)에서 빨간색(알람)으로 바뀝니다.
편차 상태 : SP와 PV 편차에 따라 색상이 변경됩니다.
사용자 정의 컬러 : 일정한 판독 값에 대해 흰색 또는 적색 화면을 선택할 수 있습니다. 

Active Color LCD Display

컴팩트한 디자인

컨트롤러의 깊이가 65 mm이므로 설치 위치의 제약이 줄어듭니다. 

Compact Design

쉬운 조작 맵, 네비게이션 가이드 및 네비게이션 키 

네비게이션 키는 컨트롤러의 구성 메뉴를 탐색하고 다양한 메뉴를 설정하는 키입니다. 네비게이션 화살표는 다음 어떤 버튼을 누를 지를 알려줍니다. 

Easy Operation Map, Navigation Guide and Navigation Keys

사용자 기능 할당 단축 키 

Programmable Function Keys운전 모드 전환, 운전 / 정지, 프로그램 패턴 선택, 리모트 / 로컬, 알람 래치 해제 및 PID 파라미터와 같이 자주 사용되는 기능을 쉽게 할당 할 수 있습니다. 외부 스위치의 기능을 래더 시퀀스 프로그램을 사용하여 전면 패널 키에 할당 할 수도 있습니다.

텍스트 스크롤

Scrolling Text

UTAdvanced에는 수정중인 파라미터를 표시해주는 텍스트 스크롤 기능이 있습니다. 텍스트 스크롤 기능을 해제 할 수 있습니다.

다중 언어 지원

Multiple language support

UTAdvanced는 영어, 스페인어, 프랑스어 및 독일어 등 다양한 언어가 가능합니다. UTAdvanced를 현지 언어로 사용할 수 있습니다.

사용자가 설정할 수 있는 초기값

User settable default values사용자가 설정한 파라미터 값 (SP, P, I, D, ALM1 등)은 컨트롤러의 초기값으로 저장할 수 있습니다. 파라미터 설정 값이 실수로 변경 되더라도 간단한 조작으로 원래의 설정값으로 복원 할 수 있습니다.

2가지 색상 선택 가능 (흰색 또는 검은색)

UT55A/UT52A White & Black Models

작업장에 어울리는 색상으로 흰색 (연한 회색) 또는 검정색 (진한 회색) 중에서 선택할 수 있습니다.

파라미터 설정

LL50A 파라미터 설정 소프트웨어 (별도 판매)를 사용하면 쉽게 파라미터를 설정할 수 있습니다.

Parameter Setting

메시지 기능

메시지 기능과 접점 입력을 사용하여 미리 등록된 메시지를 인터럽트에 의해 PV 화면에 표시 할 수 있습니다. 
메시지는 LL50A 파라미터 설정 소프트웨어를 사용하여 등록됩니다. 메시지는 20 자의 영문, 숫자로 제한됩니다.                      최대 4 개의 메시지를 등록 할 수 있습니다.

Message Function

빠른 설정 기능

조작에 필요한 최소한의 파라미터를 설정할 수 있습니다. 

보안 기능

암호 기능으로 의도하지 않은 파라미터 설정 변경을 방지 할 수 있습니다. 
암호가 설정되어 있으면 Setup Parameter Setting (Setup 파라미터 설정) 화면으로 이동할 때 암호가 필요합니다. 
암호를 입력하여 Setup 파라미터 설정 화면에 접속할 수 있습니다. 

Networking

통신 기능

간단하고 쉬운 네트워크 연결 가능 !
컨트롤러에 내장된 기능으로 컨버터가 필요없고 배선이 간단해집니다.

Communication Functions

Modbus/TCP

컨트롤러가 모든 이더넷 네트워크에 연결 가능하고 해당 네트워크의 컴퓨터 또는 장치와 데이터를 교환할 수 있는 프로토콜인 Modbus TCP / IP.

  • 제어 장치를 응용 프로그램에 간단하게 통합할 수 있습니다
  • 모든 Modbus TCP / IP 소프트웨어와 호환됩니다. 
  • Modbus 기능 코드 03, 06, 08 및 16 지원.
  • 게이트웨이 기능은 RS-485 Modbus 장치가 이더넷을 통해 통신할 수 있게합니다.
  • 간편한 통신 네트워크의 배선 및 설정으로 인건비 절감. 
  • 물리층 : 10 BASE-T/100 BASE-TX 
  • 최대 연결 수 : 2

Modbus / TCP

Modbus/RTU

UTAdvanced (슬레이브 장치)의 데이터는 Modbus RTU 기능을 사용하여 DXAdvanced에 저장하고 표시할 수 있습니다.

Modbus / RTU

개방형 네트워크 (PROFIBUS-DP, CC-Link, DeviceNet)

내장된 Open 네트워크로 PLC에 직접 연결 가능합니다.

  • UTAdvanced에서 데이터를 읽습니다
  • 파라미터 설정값을 UTAdvanced에 씁니다

예 :

PC-Link

Peer to Peer

래더 시퀀스 프로그램을 사용하여 통신 가능한 UTAdvanced간에 아날로그 데이터 및 상태 데이터를 교환할 수 있습니다.

예 : 입력 오류가 발생한 UTAdvanced는 다른 UTAdvanced로 신호를 전송하여 UTAdvanced를 MAN으로 설정하여 전체 시스템을 안전 모드로 전환합니다. 이 경우 안전 메커니즘은 UTAdvanced에 내장될 수 있으며 호스트 시스템은 필요하지 않습니다.

Peer to Peer

협조 운전

협조 운전에서 단일 UTAdvanced 온도 조절계는 마스터 조절계로 사용되며 여러 개의 UTAdvanced 또는 다른 UTAdvanced 디지털 지시 조절계는 슬레이브 조절계로 사용됩니다.

슬레이브 조절계는 마스터 조절계의 동작에 따라 운전됩니다. 

Coordinated Operation

PC 링크

범용 컴퓨터 또는 UTAdvanced 시리즈 링크 모듈과 FA-M3R (레인지 프리 컨트롤러)의 시리얼 커뮤니케이션 모듈과의 통신에 사용되는 프로토콜.

PC-Link

신뢰성

제품 3년 보증*1

Yokogawa가  오랫동안 축적해온 높은 신뢰성과 품질을 뒷받침합니다. 3 year warranty

RoHS/WEEE 준수

전면 패널 방진 방습 (NEMA4*2 /IP66)

UTAdvanced는 세척 가능한 제어 패널이 있는 식품 가공 장비에도 사용할 수 있습니다. 

Reliability

  1. 3년 보증기간은 공장 출하 후 36개월입니다. 
  2. 호스 다운 테스트

Specifications

ITEM UT75A
PV input Input type Universal input (TC, RTD, mV, V, mA)
Number 1(Std) 2(Max)
Indication accuracy ±0.1% of F.S.
Number of Control loops   1(Std) 2(Max)
Control scan period   50, 100, 200 msec
PV/SP data display   14-segment, 5 digits, Bar graph LCD display
Control outputs (MV) Type Relay, Voltage Pulse, Current
Algorithm ON/OFF, PID (Continuous, Time-proportional), Heating/Cooling, Position-proportional
Digital inputs Number 3(Std) 8(Max)
Type SP No.Change, PID No. Change, A/M Change, etc
Digital outputs Number 3(Std) 8(Max)
Function PV High, PV Low, Dev High, etc
Number of Program pattern Number 1
Number of program segment Number 20(Max)
Retransmission Number 1
Type PV, SP, OUT, etc
Remote (aux.) input (option) Number 1 or 2
Type 1 to 5 V, etc
Communication (option) Number 1 or 2
Type RS-485, Ethernet, PROFIBUS-DP, CC-Link, DeviceNet
Other specifications Power supply 100 to 240 VAC (+10%, -15%) or 24 VAC/DC (+10%, -15%) (option)
Power consumption Max 18 VA
Mass Max 0.5 kg

Comparison Chart (UT75A/UT55A/UT52A/UT35A/UT32A)

  UT75A UT55A UT52A UT35A UT32A
Model UT75A UT55A UT52A UT35A UT32A
Size 1/4 DIN    
1/8 DIN      
Depth from the panel surface (mm) 65 65 65 65 65
Number of Control loops Standard (Maximum) 1(2) 1 1 1 1
Control Scan Period (msec) Choice 50/100/200 Choice 50/100/200 Choice 50/100/200 200 200
Display Function Number of PV Display Digits 5 5 5 5 5
Active Color PV Display Function
Guide Scroll Display Function
Message Display Function
Bar graph display (Number) ✓(2) ✓(2) ✓(2) ✓(1) ✓(1)
PV Input Indication Accuracy (% of F.S.) 0.1 0.1 0.1 0.1 0.1
PV Input Type TC
RTD (3-wire)
RTD (4-wire)    
mV, V
mA
Number of Analog Inputs Standard (Maximum) 1(4) 1(4) 1(2) 1 1
Number of SPs (PIDs) Maximum 20(16) 8 8 4 4
Number of Control Modes Maximum 9 8 8 1 1
Number of Control Types Maximum 8 8 8 5 5
Control Output Type Relay Contact Output, Voltage pulse output, Current output
Algorithm ON/OFF
PID (Continuance, Time Proportion)
Position proportional
Heating/cooling
Number of Analog Outputs Standard (Maximum) 2(3) 2(3) 2(3) 2 2
Number of Digital Inputs Standard (Maximum) 3(8) 3(9) 3(5) 2(7) 2(4)
Number of Alarms   8 8 8 4 4
Number of Digital Outputs Standard (Maximum) 3(8) 3(18) 3(5) 3(8) 3(5)
Communication RS-485 communication (Maximum) ✓(2) ✓(2) ✓(1) ✓(1) ✓(1)
Ethernet communication    
Open Network (CC-Link/PROFIBUS-DP/DeviceNet)    
Various Function Quick Setting Function
Split Computation Output Function    
Ratio and Square Root Extraction Function    
Remote SP Function    
24 V DC Loop Power Supply Function  
Heater Break Alarm Function  
(Standard type)

(Standard type)

(Standard
type or
Heating/
cooling type)

(Standard
type or
Heating/
cooling type)
Ladder Sequence Function (Number of max. steps) ✓(1000) ✓(500) ✓(500) ✓(300) ✓(300)
Other specifications Power Supply AC100 V to 240 V
AC/DC 24 V
Dust and waterproof Level of Front Panel NEMA4 *1 (IP66) NEMA4 *1 (IP66) NEMA4 *1 (IP66) NEMA4 *1 (IP66) NEMA4 *1 (IP66)
Configuration Tool Via Light-loader Communication
Via Maintenance Port
Communication
Via RS-485/Ethernet
communication
✓/✓ ✓/✓ ✓/- ✓/✓ ✓/-

The table above includes specifications of the standard models only.
* 1: Hose down test only.

Input Range

Input type  
TC K, J, T, B, S, R, N, E, L, U, W
PL-2, PR20-40, W97Re3-W75Re25
RTD JPt100, Pt100
DC Voltage 0.4 to 2.0 V, 1.0 to 5.0 V, 0.0 to 2.0 V, 0 to 10 V, -10 to 20 mV, 0 to 100 mV
DC Current 4 to 20 mA, 0 to 20 mA

자료실

Overview:

With advances in process automation comes a greater need for level measurement and control. As pressure on at the bottom surface of a liquid is proportional to the height of the liquid's surface, you can measure pressure using a differential pressure transmitter to detect the level of the liquid, acquire the data on the UT75A Digital Indicating Controller, and use the measurements to control the tank level.

업종:
Overview:

Adding the CP calculation option to the advanced UT75A Digital Indicating Controller enables CP (Carbon Potential) control. CP calculation can be carried out with just one line of a UT75A ladder program.

업종:
Yes, with a ladder program. The model that supports this is the UT75A. You can use up to 3 moving average (MAV) calculations.
No, there is no conversion tool, but note that custom calculations can be replaced with ladder sequence programs. See (TI 05P01B41-03EN): “Conversion Table of UT750 Custom Computation into UT75A Ladder Program.” ...
When the input switches, the controller tracks the PV and suppresses sudden control output changes (bumpless).
I want to use 2 communication systems.
(ns-faq-ut-2085-select)
You can install 1 system from Ethernet/CC-Link/DeviceNet/PROFIBUS-DP/RS-485 on the UT75A, UT55A, UP55A, plus an additional system of RS-485. Specify these when ordering.
Yes. The communication protocol is the same, but note the difference below. You can also install two systems for use with separate protocols. The maximum speed of RS485 communication using the 2nd digit of the specification code is 19.2 kbps. The UT5...
Check whether the input on the primary loop is normal.If the input is abnormal, the unit won't switch to cascade mode.
First, set the secondary controller to AUTO operation (CAS goes out), then auto-tune that controller. Next, place it in the cascade state (CAS lights), then auto-tune the primary controller.
If you won't use the OUT and OUT2 terminal relay contacts for control output or some other purpose, you can use these models. UT55A heating/cooling model, UT57A 2 loop model For a program controller, the UP55A heating/cooling model   ...
Yes. Perform correction on A.BS of each input item.
Yes, by using the following alarm types. Analog input PV upper-limit alarm Analog input PV lower-limit alarm Analog input RSP upper-limit alarm Analog input RSP lower-limit alarm Analog input AIN2 upper-limit alarm Analog input AIN2 lower-lim...
This is supported on the UT75A, UT55A, UT52A, UP55A, and UM33A by using the 10-segment linearizer function.
Try the broken line function. That function comes with the UT52A, UT55A, UT75A, UP55A, and UM33A.
Yes, the UT75A + LL50A setting software (sold separately) can handle that.
There are three models: the UT75A and UT55A Digital Indicating Controllers, and the UP55A Programmable Controller.
Can I set up 4 alarm relay outputs?
(ns-faq-ut-2016-setting)
If you don't need to use the control relay output, you can use it as an alarm relay output. Adding that to the standard-equipped 3 alarm relay outputs gives you 4 outputs.
The Ethernet setting switch is designed to enable Ethernet related parameter settings. Setting the parameter to ENTRY "1" enables the parity, IP address, subnet mask, default gateway, and port number settings. When you set this parameter to...
This means that each unit can be accessed via Ethernet from up to 2 locations at once.
As for individually writing parameters via CC-Link, changing OUT area values constitutes a write request. In your case, since the OUT area value hasn't changed from the previous value, the SP value is notoverwritten. As a fix, periodically copy t...
Use profile number 0. You can also use CCLink even if you delete the parameter assignments of Modbus slave 2 from the user profile.
RUN/STOP is set to contact input DI2 by default, and takes precedence over communication. Set S/R to OFF with DI.SL.
Reference OUT_L1 (process monitoring → process data).
If not using relay contact output for control, you can use it as a 4th alarm. This alarm would be the C contact type, therefore by connecting it to the N.C. (normal close) side you can use it as an alarm terminal. Note that when changing the basic sp...
You can change it if it is in a user profile (profile no. 0).To create a user profile, use the LL50A network profile tool.
It allows communication with RS-485 compatible UTAdvanced series instruments via CC-Link. It allows acquiring data from downstream controllers that do not have CC-Link communication, and writing parameters.
The output is restricted to a lower limit of 3.2 mA (-5%) and an upper limit of 20.8 mA (105%), but only when the transmission output scale RTH and RTL settings are the same as the PV input range.
Open registers for the number of proprietary stations per unit. For example, if there are 3 CC-Link Ver. 1 stations are occupied, the bit area occupies 96 bits per station and a word area of 12 words per station. If the refresh device of the word are...
If a control relay output (C contact) is unused, you can use it for alarms.
See the UTAdvanced Series Communication Interface (RS-485, Ethernet) User's Manual.
No, a UT100 series instrument cannot connect. Only other UTAdvanced series instruments can connect.
The alarm setting values from local are carried over.
You can do this by assigning a user function key Fn, F1, or F2* (within the KEY setup parameter). * Depending on the model (UT75A, UT55A, UT52A, UT35A, UT32A)
If you connect a shunt resistance to the input terminal of the receiving side meter, you can input it as voltage. For example, if you connect a 250 Ω shunt resistance to 4–20 mA output, it's 1–5 V. Make the resistor, including t...
Proportional band P has data of up to 1 decimal point. By contrast, communication data has no decimal point. If you want to write 100.0% to P, send 1000. For differential and integral time, the data has no decimal point.
b.out indicates a burnout on the measurement input. It appears when measurement input wiring is disconnected. Check the sensor and wiring.
Yes. Data in D register number D2005 is the valve opening value. Note that with a position proportional controller, D2006 is the PID computed value.
BR is the communication speed for CC-Link. BPS is the communication speed for the Modbus master function (RS485).
When writing individual parameters via CC-Link communication, if the data values to write are not different from the existing ones, overwriting of the values does not occur. If you write all parameters by individual communication address and the valu...
When the writing flag (RX1) is ON, the next write process can't proceed. Make sure the writing flag (RX1) is OFF before performing a write process.
If outside of the parameter setting range, data is not written.
No. Only the conventional CC-Link Ver. 1.1 or 2.0 standards are supported.
Autotuning is performed when you turn AT_L1 in the OUT area to ON (= set to 1). Please make sure that AT_L1 in the OUT area turns OFF (= set to 0) after autotuning is finished.
Communication itself is available in either Remote or Local mode. Switching to Remote mode is for overwriting r.SP from an external device.
Use a current generator with a SINK function (transmitter simulation).
On the cascade primary controller, if there is no secondary SP information, when you switch from AUTO to cascade on the cascade secondary controller, the secondary settings change abruptly, so control is interrupted. To avoid this, in advance, send t...
The display is blank if you turn ON the power while a a dedicated LL50A cable is plugged into the maintenance port. Try removing the cable and restarting.
I can't find a parameter I want to set.
(ns-faq-ut-2001-setting)
Please see the parameter map for your specific model. UTAdvanced Series Parameter Maps and Lists
In the case of the difference lower limit alarm, the alarm setting is a negative value. For example, you need to set it to "-5°C."
Yes. Use a UT link module for the FA-M3, and use PC link communications (RS-485) for the temperature controller communication protocol selection.
Program changes for reading PV and OUT, writing SP, and other basic parameters are not necessary. There are registers and relays that support the GREEN series. For details see the UTAdvanced series communication interface (RS-485, Ethernet) user'...
Generally you should create programs in "user ladder" mode. If needed, you can rewrite the input ladder and output ladder portions.
The DATA register uses a 4-byte floating point number, therefore it displays a lot of digits. Try using the K or P registers, since they handle 2-byte integer data.
Can I use analog input in computations?
(ns-faq-ut-2032-program)
You can use it in ladder programs. On the UT55A, you can acquire up to 4 analog inputs.
Variable parameters P01-P10 can be rewritten via communication. You'll need to use the variable parameters as constants.
On the LL50A, change the system data's ladder sequence function from USE to DON'T USE. If not using the LL50A, initialize the main unit.
Yes. Use the PON flag on contact B.
It won't start while the system data or parameter setting screen is displayed. Close those screens and restart.
Check the operation of the program on the LL50A ladder program monitor.
The comparison commands of the digital indicating controllers (UT55A/UT52A/UT35A/UT32A) and program controllers (UP55A/UP35A) compare integers (rounded to the nearest decimal). If making comparisons that include decimals, first multiply the necessary...
For contacts that have duplicated functions, it is necessary to turn them OFF on the setup parameter side.
Please see the document below. It is an example of wiring and settings for pH control using the Quick Setup function. Affected models: Standard UT52A/UT55A models (if there are 2 types of chemicals, select the heating/cooling model) Setup procedure,...
Please see the document below. It is an example of wiring and settings for controlling electric furnace temperature with a thyristor using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Furnace Temperature with...
Please see the document below. It is an example of wiring and settings for controlling electric furnace temperature with solid state relays using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Furnace Temperatu...
Please see the document below. It is an example of wiring and settings to control flow with inverters using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Flow with Inverters)" ...
Please see the document below. It is an example of wiring and settings for tank level ON/OFF control using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Tank Level ON-OFF)" ...
Please see the document below. It is an example of wiring and settings for tank level proportional control using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Tank Level Proportion)" ...
Please see the document below. It is an example of wiring and settings for tank pressure control using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Tank Pressure)" ...
Yes, if using a UTAdvanced series instrument with the RS-485 communication option. Set the RS-485 protocol on the main unit to 8 (MBRTU: Modbus RTU). The initial value is 8. Select RS-485 in the LL50A communication execution screen, and make the comm...
If the LL50A's display setting is not PRO, some parameters won't display. Change the LL50A's display parameter as follows: Display > Parameter > Display level > Professional. The LL50A's display level must be set separately f...
You can display and acquire PV, SP, and OUT values as trend data. The trend data you acquire can be saved as a CSV file.
Yes. Use the SCAL ladder program command.
It is 1/20000. That is equivalent to approximately 14.5 bits.
Please see the document below. It is an example of wiring and settings for tank temperature control using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Tank Temperature)" ...
Please see the document below. It is an example of wiring and settings for controlling furnace temperature with a motorized valve using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Furnace Temperature with a ...
Please see the document below. It is an example of wiring and settings for controlling heat exchanger temperature using the Quick Setup function. Setup procedure, "UTAdvanced Quick Setting (Controlling Heat Exchange Temperature)" ...
Yes. The SP ramp up (UPR)/SP ramp down (DNR) function supports changing the SP value with the UT55A front panel buttons or remotely.
If you register the A1 and A2 parameters (for setting alarms 1 and 2) to the select screen, you can display the alarm 1 and 2 settings simply by pressing the DISPLAY key repeatedly. Set the CS1 and CS2 select screen parameters to "2504" and...
Yes, the output signal can be reversed. In the setup parameter OUT menu, set the OU.A parameter to "20–4."
How can I enter initial settings?
(ns-faq-ut-2064-setting)
Please see an operation guide. Controller operation guides are available for standard and detailed models. (Ex.: UT55A-000-01-00 is a standard model, and UT55A-NNN-01-AN is an detailed model). Note that you can refer to the user's manual for any ...
If OVER is displayed, the PV value will be 105% of the measurement range. The control output will be the result that is calculated using this PV value. On a -OVER, the PV value is calculated as -5% of the measurement range.
The controller's operation may be set to START/MAN. Check the controller operation indicator on the front panel.
There might be breakage in a line. Check input wiring and sensors.If the input is restored, B.OUT will be cleared automatically.
(1) Check the wiring: In MAN mode, set OUT display. Use the UP and DOWN keys to confirm operation of the control valve, and that the OUT value changes. The UP key operates the normal rotation side relay, and the DOWN key operates the reverse rotation...
Is a terminal cover included?
(ns-faq-ut-2088-select)
The UT52A, UT55A, UP55A, and UT75A come standard with terminal covers. For the UT32A, UT35A, UP35A, UP32A, and UM33A, specify the /CV option when order on or after May 31, 2015. They are also sold separately. Models: UTAP001UT75A, UT55A, UT35A, UP55A...
In this case, 20 mA is the minimum value of PV input, and 4 mA is the maximum. In the setup parameter PV menu, set RH=4.00 and RL=20.00 (the input range maximum and minimum values). For the PV input scale max, min, and decimal place, set SH=0, SL=-10...
Per the metering law, in Japan you can only use °C. For customers who require overseas-specification products that can display Fahrenheit for embedding in a device exported outside of Japan, please contact your dealer or Yokogawa representative. ...
The green numbers in the upper left part of the SP display are the SP numbers. If you register PID numbers in the select screen, you can display them in the SP display area (in orange). Register PIDN_L1_1 under Setup parameters > CSEL > CS1. ...
Check the following. Is the control type (CNT) ON/OFF, or 2 position 2 stage control?--> If so, change it to something other than that. Is the STOP lamp lit? --> Start operation (RUN). Is the MAN lamp lit? --> Set it to AUTO.   ...
Check the operation mode and communication protocol. If the operation mode is Remote (REM lights) and it's set to coordinated (PSL=CO-S), an error will occur if there is no wiring.
The UT's voltage pulse specifications are: ON voltage 12 VDC or more; load resistance 600 Ω or more; ON voltage 0.1 VDC or less. For example, in the case of the Omron G3PH (operating voltage DC4-30 V, input current 5 mA or less), up to 4 un...
You can switch the output at about ±0.25% of the input range relative to the set point.
At the time of shipment from the factory, the PID display is assigned to the Fn key on the UT front panel. If you press the Fn key, the currently used P (proportional band) is displayed. You can press the DOWN arrow key to check other items.
Try the overshoot suppression function (super function). Turn on SC: Operation parameter > TUNE > SC
The common for all GREEN series alarm relay outputs are shared. In the UTAdvanced series, each alarm relay output has its own common. If used the same way, use external wiring to connect common to common.
By factory default settings, the PID number is linked to the SP number. You can change the setting with the zone PID selection parameter (setup parameter CTL > ZON).
By factory default setting, the alarm function still works when operation is stopped (STOP). You can change the setting by using the alarm mode parameter (operation parameter ALRM > AMD).
What is the alarm standby function?
(ns-faq-ut-2111-spec)
Standby means that even when an alarm condition occurs it is ignored and the alarm stays off until the alarm condition ends. When the signal enters a non-alarm region, standby mode ends. Standby works in the following situation. When powering on ...
They are set with the same industrial quantities as the input units.
Yes, as a percentage of the PV input range span or output span.
For communication errors, the left side decimal point of the symbol display on the main unit blinks. If the SD or RD indicators light on upstream devices, check whether both are blinking.
You can specify PID parameter groups for each SP number. Each PID parameter group includes PID, output limiter, hysteresis, and other items.
For controllers, the status detection minimum hold time is the control interval + 50 ms. Also, for indicating alarms, it's the input sampling interval + 50 ms.
It's time proportional PID. That means that in addition to relay output, it can support TRIAC and voltage output. With time proportional output, control calculation result is output using the pulse width of an ON/OFF signal proportional to time. ...
The UTAdvanced series is not a CCC standard scope. Since it has acquired the GB standard, it can be used in China.
You can do this with the AMD alarm mode settings (within the ALRM operation parameter). 0: Alarm always active 1: Alarm not active during operation stop 2: Alarm not active during operation stop or manual operation
Set alarm types AL1–4 or 8 (ALRM operation parameter) to 0.0.0.00.
Yes, set parameter AL1.S (AL1 function select) to 4529.
Use a relay that supports miniscule currents. The minimum ON current of a contact input (DI) is approximately 1 mA.
By turning the OLMT output limiter switch OFF, the output limiter is disabled during manual operation.
Check whether the MAN lamp is lit. If it is, control output will not change. Press the A/M key to switch to AUTO.
Try the PV tracking function (PVT=ON). This function is useful for preventing sudden changes in the PV value. When operation starts, the PVT starts by matching SP to PV, and then uses an SP slope function (TMU, UPR, DNR) to gradually return SP to the...
Check the cycle time (CT) setting. For voltage output, try a cycle time setting of around 1 to 5 seconds.
It appears when the controller's operation mode is RUN and MAN.
Choose PC link communication (sum check enabled or none). Please also refer to the Mitsubishi Touch Panel GOT catalog and user's manual.
Perform tuning with these reference values: P=150 to 200, I=10 to 20, D=OFF.
Perform tuning with these reference values: P=150 to 200, I=10 to 20, D=OFF.
Try proportional control. Perform tuning with these reference values: P=10%, I=OFF.D=OFF, MR=0%.
Yes. Set the following: IN=1-5V, RH=1.000, RL=5.000, SDP=2, SH=0.00, SL=-10.00.
Per factory parameter settings, the EV lamp on the UT and UM is assigned to alarms, and may light depending on the measured input (PV) and setting values. Configure your EV lamp and alarm type settings to match your operating conditions.
In your ladder program, use variable register P01 and others, and write the P01 value via communication. Then do a MOV of the P01 data to the tracking input value (TRK_CTL).
“b.out” on the PV display indicates a break in the input. Check whether the signal from the sensor is getting through. Also, to narrow down the cause, you can short the input terminal of the UT itself, then if the UT's input is normal...
At DC24 V: Approximately 17 A, 1.5 ms At AC100 V: Approximately 4.5 A, 3 ms At AC240 V: Approximately 11 A, 3 ms
Per the specifications, the accuracy of type K at 0°C or higher is ±0.1% ±1 digit. The measuring range in this case is that of the selected input type, -270.0 to 1000.0. You can calculate the accuracy as follows. ±0.1% of 127...
It is approximately 0.16 mA.
Check the key lock. If you see the R.SP display, in Remote mode (REM), that means SP is being set by an external (upstream, etc.) device and cannot be changed.
Yes. The read registers will be control output D7621 (OUT_OUT) and transmission output D7624 (OUT_RET). Note that these registers are for data -1500 to 31500 (equivalent to -5.0% to 105%).
Yes. The data will be -1500–31500. For the OUT terminal output, D7621(OUT_OUT) For the RET terminal output, D7624(RET_RET) For the OUT2 terminal output, D7623(OUT_OUT2L)  
Yes, by using the message function. This function assigns messages that have been registered in advance to the PV value display section, and displays them based on contact input ON/OFF states. Setting example: MG1 = 4353
This function operates during P and PD control (when integral time I = OFF). The manual reset value is the output value when PV=SP.
Q: I'm connecting a UT with CC-Link communication to another downstream UT via RS485 communication (Modbus master function). However, the RS485 communication terminal of the UT with CC-Link communication is a 2-wire system, and that of the other ...
Make the UP the parent station of two UT child stations and run the coordinated communication.
Yes. Set the DR (direct/reverse operation switching) parameter of the PID item to DIR (direct operation).
When you turn ON the power, it shows up on the self-diagnostic screen that appears for a few seconds. The 3-digit number in the SP display section is the basic suffix code. (Ex.) For the UT55A-210-01-00, the number "210" appears. ...
You can do this with the SET/ENT key system. Set MAN.T to ST.ET.
Select the type that is closest to the temperature range span that you are using.
You cannot apply an external voltage. You can connect either a no-voltage contact or a transistor contact.
For analog output of calculated results to the OUT terminal, set the output selection type OT to 00.00 and the transmission output type 01RS to OUT1.
For analog output of calculated results to the RET terminal, set the transmission output type RTS to OUT1.
For analog output of calculated results to the OUT2 terminal, set the first two digits of the output selection type OT to 00, and the transmission output type 02RS to OUT1.
You can do this with the pattern 2 transmission function. With the program pattern 2 transmission function, you can create and transmit program patterns at the same time, aside from program patterns used in control.
65 mm. For details, see the specifications of individual models.
Yes. Assign an I relay to the DO parameter.
Yes, by using PID switching. Generally, you set heating control to reverse action and cooling control to direct action.
Yes, as long as the total input and wiring resistance of the connected instruments is 600 Ω or less.
Do you sell terminal covers?
(ns-faq-ut-2233-other)
Yes. Model: UTAP001 Supports: UT75A, UT55A, UT35A, UP55A, UT35A Model: UTAP002 Supports: UT52A, UT32A, UP32A, UM33A
Not with parameter settings, but you can do this with a ladder program.
Not with parameter settings, but you can do this with a ladder program.
No, use 1 contact per input. If you connect multiple inputs, when you turn OFF the UT, the impedance lowers and mis-operation can result.
No, it only comes in white.
It’s from U-RD. Please purchase them from our dealers.
For a power failure of approximately 5 seconds or more, you can do this with the restart mode R.MD setting. For power failures of less than approximately 5 seconds, the control operation prior to the power failure continues. ...
You can use this with suffix codes /LP, /L1, /LCH, /L4, and /LC4. For wiring to a 2-wire transmitter, the controller is equipped with an insulated sensor power supply (21.6 to 28.0 VDC). ...
You can download these items from the Partner Portal member site *Log-in Required. You must register (free) to use Partner Portal.

Downloads

기술 및 솔루션, 요꼬가와에 대한 자세한 정보를 찾고 계십니까?

견적 및 기술문의

Top