Name: FN510 무선 다기능 모듈
Brand: Yokogawa
SKU: fn510-field-wireless-multi-function-module

Brochures
Instruction Manuals
General Specifications
기술 지원

"무선 통신 모듈 FN110"이 장착 된 무선 다기능 모듈은 무선 장치로써 무선 네트워크에 연결할 수 있습니다. 이 제품은 연결된 센서에서 데이터를 수집하여 FN110을 통해 무선 네트워크로 전송합니다. 개요 및 상세 정보는 "무선 통신 모듈 FN110"의 일반 사양을 참조하십시오.

다양한 입력 / 출력 기능 :
아날로그 입력, 디지털 입출력 또는 펄스 입력을 선택할 수 있습니다 (측정 코드 : A).
ACAI 기능; AC 전압에서 전용 가속도계 입력으로 가속 또는 속도를 측정 할 수 있습니다 (측정 코드 : C).
무선 네트워크에 다양한 센서 연결 :
이 제품은 4-20 mA 아날로그 장치 (측정 코드 : A) 또는 전용 가속도계 (측정 코드 : C)에서 얻은 센서 값을 무선 네트워크를 통해 호스트 시스템에 전송합니다.
설치 유연성 :
케이블을 제거하면 이전에는 접근 할 수 없거나 비용(케이블 관리 등)이 많이 드는 위치에 장치를 설치할 수 있습니다.
작고 가벼운 LCD 하우징 :
이 제품은 공정 데이터와 통신 상태를 표시하는 LCD가 내장 된 작고 가벼운 하우징을 가지고 있습니다.

Power Supply Specifications	Battery	Dedicated battery pack Rated voltage: 7.2 V Rated capacity: 19 Ah Battery Pack:2x primary lithium-thionyl chloride batteries With battery case (batteries sold separately)
Performance Specifications	Update Period	[Measurement code: A] 1 to 3600 s selectable* *： When using the digital output, more than 2 s is accepted. [Measurement code: C] 10 to 3600 s selectable
Performance Specifications	Battery Characteristics	[Measurement code: A] Typical battery life when using analog input or digital input is 10 years^{* 1} or 7 years^{* 2} and when using digital output with always on is 3 years^{* 3} or 2 years^{* 1} in the following conditions.^{* 4} Ambient temperature: 23 ±2°C Device role: IO mode LCD display: off 1: Update period: 10 s 2: Update period: 5 s 3: Update period : 30 s 4: Environmental condition such as vibration and the type of connected device may affect the battery life. [Measurement code: C] Typical battery life when using piezoelectric accelerometer is 10 years^{* 1} or 2 years^{* 2} in the following conditions.^{* 3} Ambient temperature: 23 ±2°C Device role: IO mode LCD display: off Sampling frequency: 20 kHz Sampling points: 1024 points 1: Update period: 60 s 2: Update period: 10s *3: Environmental condition such as vibration and the type of connected device may affect the battery life.
Functional Specifications	Input	[Measurement code: A] See Table 1. [Measurement code: C] See Table 2.
	Output	Communication specifications between this product and FN110 are below. Communication Mode: Half-duplex communication (RS485 compliant) Communication Speed: 9600 bps Connector: 5-pin round connector dedicated Cable: Max 20 m (dedicated cable)
	Power Supply	Power supply to the FN110 Supply voltage: 3.5 V Supply current: 50 mA Power supply to sensors [Measurement code: A] None [Measurement code: C] See Table 2
Installation Environment	Ambient Temperature Limits	Operating: -40 to 85°C (attitude up to 3000 m) -30 to 80°C (LCD visible range) Storage: –40 to 85°C
	Ambient Humidity Limits	Operating: 0 to 100%RH (non-condensation) Storage: 0 to 100%RH (non-condensation)
	Ambient Temperature Gradient	Operating: ±10°C/h or less Storage: ±20°C/h or less
	Vibration Resistance	0.21 mm P-P (10 - 60 Hz), 3G (60 - 2 kHz)
	Shock Resistance	50 G 11 ms
Regulatory Compliance Statements	CE Conformity	EMC: EN61326-1 Class A Table 2, EN55011 Class A Safety: EN61010-1 (Indoor/Outdoor use)
	Canadian Safety Standards	CAN/CSA-C22.2 No.61010-1 CAN/CSA-C22.2 No.94.1, CAN/CSA-C22.2 No.94.2 IEC 60529
	Degrees of Protection	IP66, IP67 and Type 4X apply when the connector is properly tightened.
	Explosion Protected Types	FM (United States or Canada), ATEX, IECEx Intrinsically safe Approval
Physical Specifications	Connections	Refer to “MODEL AND SUFFIX CODES”
	Housing Material	Plastic (Polycarbonate)
	Weight	500 g (without mounting bracket, clamp, and battery)

[Measurement Code: A]
Table 1. Input / Output for Measurement code A

Function	Item	Specifications
*4-20 mA Analog Input (AI)^{ 1}**	Number of input channels	1
	Input signal	4 to 20 mA DC
	Range	0 to 25 mA
	Internal shunt resistor	10 Ω
	Accuracy	±16 uA
	Temperature coefficient	±3.2 uA/10°C
*Digital Input (DI) ^12*	Number of input channels	2
	Input signal	Dry contact input
	Maximum on resistance	200 Ω
	Minimum off resistance	50 kΩ
	Current value when contact is on	IN1：0.2 mA IN2：1 mA
*Digital Output(DO) ^13*	Number of output channels	1
	Output signal	Dry contact output
	Maximum load current	125 mA DC
	Maximum load voltage	30 V DC
*Pulse Input (PULSE) ^12*	Number of input channels	1
	Input signal	Dry contact input
	Maximum on resistance	200 Ω
	Minimum off resistance	50 kΩ
	Minimum detection time ^*4	5 ms
	Maximum input frequency	100 Hz
	Counter range	0 to 999999

*1: The input channels are non-isolated and share one common ground.
*2: Do not apply a voltage to a DI or PULSE from the outside.
*3: The digital output terminal is configured as open-drain. The voltage and current applied to a digital output terminal should be within the specified range.
*4: Minimum time required to detect an contact becomes off.

[Measurement Code: C]
Table 2. Input for Measurement code C

Function	Item	Specifications
AC Analog Input (AI)	Number of input channels	1
	Input signal	0.1 to 3.2 V
	Sensing mode^*1	Acceleration, Velocity, Velocity LPF160 Hz (Gain High, Gain Low)
	Measurement data	Peak, RMS, Peak/RMS
	Sampling Frequency	1, 2, 5, 10, 20 kHz
	Sampling Points	1024, 2048, 4096 points
	Frequency range	10 Hz to 10000 Hz
	Range ^23	Acceleration: 0 to 300 m/s² Velocity:0 to 160 mm/s
	Accuracy (100 Hz) ^45	Acceleration: ±(2% of reading + 2 m/s²) Velocity: ± (10% of reading +1 mm/s)
	Sensor power supply voltage	3.4 V typ.
	Sensor power supply current	10 mA max.

*1: Acceleration mode is used to measure the relatively high frequency vibration. Velocity mode is used to measure the relatively low frequency vibration. Velocity LPF 160 Hz mode is used to measure the near 160 Hz.
*2: Range is due to combination of LN01 Piezoelectric Accelerometer.
*3: The relationship of the measurable frequency and the measurable range due to combination of LN01 Piezoelectric Accelerometer, see Figure1 and 2.
*4: This is an accuracy of only FN510. (Ambient temperature -40 to 85ºC, the entire measurement range).
*5: Measurement accuracy due to combination of LN01 Piezoelectric Accelerometer, see Table 3.

Table 3: Measurement accuracy with combination of LN01 Piezoelectric Accelerometer (reference value)

Conditions	Accuracy (100 Hz)
Ambient temperature -40 to 85ºC, the entire measurement range	Acceleration: -27 to +17% of reading ± 2 m/s^{* 2} rms Velocity: -35 to +25% of reading ± 1 mm/s rms
Ambient temperature 25±10ºC, the entire measurement range	Acceleration: ± (15% of reading + 0.8 m/s^{* 2} rms) Velocity: ± (23% of reading + 0.2 mm/s rms)

Media Publication

Leverage Wireless Communication for Vibration Monitoring

(Leverage Wireless Communication for Vibration Monitoring)

Software

Certificates

WCI certification for FN510 (433 KB)

Drawings

Field Wireless Multi-Function Module (792 KB)
LN01 Piezoelectric Accelerometer (for FN series) (505 KB)

Reference

Wireless Vibration Monitoring

FN510 무선 다기능 모듈

Overview

Details

[Measurement Code: A]
Table 1. Input / Output for Measurement code A

[Measurement Code: C]
Table 2. Input for Measurement code C

Table 3: Measurement accuracy with combination of LN01 Piezoelectric Accelerometer (reference value)

자료실

Downloads

Brochures

Instruction Manuals

General Specifications

Software

Certificates

Drawings

동영상

[Measurement Code: A] Table 1. Input / Output for Measurement code A

[Measurement Code: C] Table 2. Input for Measurement code C

Table 3: Measurement accuracy with combination of LN01 Piezoelectric Accelerometer (reference value)

Brochures

Instruction Manuals

General Specifications

Software

Certificates

Drawings

[Measurement Code: A]
Table 1. Input / Output for Measurement code A

[Measurement Code: C]
Table 2. Input for Measurement code C