Use this 10:1 active probe with the DL9240 series to realize system measurements up to 1.5 GHz BW.

Bandwidth: DC to 2.5 GHz (-3 dB)
Attenuation: 10:1 (±2%)
Input resistance: 100 kΩ (±2%)
Input capacitance: approx 0.9 pF (typ.)
Dynamic range: ±7 V
Max. input voltage: ±25 V DC + AC peak
Offset voltage: ±10 V

Use this 10:1 active probe with the DL9140 series to realize system measurements up to 1.0 GHz BW.

Bandwidth: DC to 1.5 GHz (-3 dB)
Attenuation: 10:1 (±2%)
Input resistance: 100 kΩ (±2%)
Input capacitance: approx 0.9 pF (typ.)
Dynamic range: ±7 V
Max. input voltage: ±25 V DC + AC peak
Offset voltage: ±10 V

Use this 10:1 active probe with the DL9040 series to realize system measurements up to 500 MHz BW.

Bandwidth: DC to 1.0 GHz (-3 dB)
Attenuation: 10:1 (±2%)
Input resistance: 100 kΩ (±2%)
Input capacitance: approx 0.9 pF (typ.)
Dynamic range: ±7 V
Max. input voltage: ±25 V DC + AC peak
Offset voltage: ±10 V

This 10:1 and 20:1 (selectable) passive probe is used with the 50 ohm input setting on the DL9000. The change in attenuation is realized by changing resistance on the tip of the probe.

Bandwidth: DC to 5 GHz (-3 dB)
Attenuation: 10:1 or 20:1 (±2%)
Input resistance: 450 Ω or 950 Ω (±2%)
Input capacitance: approx 0.25 pF (typ. 450 Ω), 0.4 pF (typ. 950 Ω)
Max. input voltage: 20 Vrms

This probe can be used in combination with the DL9000 or SB5000 series.

Input Resistance: 1 MΩ
                        (against GND level from each input terminal)
Input Capacitance: approx. 1.1 pF
                        (against GND level from each input terminal)
Max. operational input voltage: ±35 V
Max. differential input voltage: ±25 V
Attenuation: 1/50

Use this 10:1 differential probe with the DL9000 to realize system differential measurements up to 1.5 GHz BW.

Input Resistance: approx. 50 kΩ
                       (against GND level from each input terminal)
Input Capacitance: approx. 1.1 pF
                       (against GND level from each input terminal)
Max. operational input voltage: ±7 V
Max. differential input voltage: ±5 V
Attenuation: 1/10
                         more

This attachment set can be used with PBA2500 and PBD2000.

Spring pin (straight) x 4
Spring pin (angle) x 4
Pin (straight) x 20
Pin (angle) x 20
Pin (L shape) x 2
Micro Clip (black) x 1
Micro Clip (red) x 1
Single lead (black) x 1
Single lead (red) x 1

This probe can be used for general purpose day-to-day measurements up to 500 MHz BW. The DL9000 series comes standard with foure PB500 probes.

Attenuation: 10:1 (±2%)(When used with the DL9000)
Input resistance: 10 MΩ ±2%
Input capacitance: approx 14 pF (typ.) (When used with the DL9000)
Max. Input range: ±600 V DC + AC peak

This DC block can be used to remove the DC component from an incoming signal. Use this block if you want to remove bias voltage from reaching the PBL5000 probe.

For differential signal measurements. Order the DL9000 with the /P2 option to directly power the probe off the scope.

Attenuation: 10:1 (±3%)
Input resistance (typ.)100 kΩ
Input capacitance (typ.) 2.5 pF
Max. allowable differential voltage: ±12 V DC + AC peak
Max. common mode voltage: ±30 V DC + AC peak

This probe doesn’t need an extra power connection (LEMO connector), can be recognized automatically and adjust zero position from the operation of the DL9000 series.

Bandwidth: DC to 100 MHz (-3 dB)
Max. continuous input range: 30 Arms, 50 A peak

Clamp-type current probe. Order the DL9000 with the /P2 option to directly power the probe off the scope.

Bandwidth: DC to 100 MHz (-3 dB)
Max. continuous input range: 30 Arms, 50 A peak

This probe doesn’t need an extra power connection (LEMO connector), can be recognized automatically and adjust zero position from the operation of the DL9000 series.

Bandwidth: DC to 50 MHz (-3 dB)
Max. continuous input range: 30 Arms, 50 A peak

Clamp-type current probe. Order the DL9000 with the /P2 option to directly power the probe off the scope.

Bandwidth: DC to 50 MHz (-3 dB)
Max. continuous input range: 30 Arms, 50 A peak

Bandwidth: DC to 350MHz (-3dB)
Attenuation ratio: 1/10 (Fixed)
Maximum input voltage: 400Vrms
Cable length: 3m

Bandwidth: DC to 400MHz (-3dB)
Attenuation ratio: 1/100 (Fixed)
Maximum input voltage: 1,000Vrms, 6,000Vpeak
Cable length: 1.2m

Bandwidth: DC to 250MHz (-3dB)
Attenuation ratio: 1/100 (Fixed)
Maximum input voltage: 1,000Vrms, 6,000Vpeak
Cable length: 3m