Reducing Refinery Energy Costs

Download (199 KB)

An online steam management program can help refineries manage their steam and utility systems more energy efficiently and reduce their operating costs through optimisation and monitoring

Diego Ruiz Massa and Carlos Ruiz García Soteica Europe SL
David Nelson and Gary Roseme Nelson & Roseme Inc.
Manuel Lázaro Meléndez and María Sartaguda Pardos Repsol Petróleo SA

The Repsol YPF Tarragona refinery in Spain operates a large, complex steam system. In order to make the refinery more energy efficient and to reduce operating costs, a proprietary online steam management program called Visual MESA was implemented. This allows operators and engineers to:

Monitor steam production and use

Optimise the production and use of steam, fuel and power to reduce costs

  • Perform "what-if" studies
  • Audit the system with continually validated data.

The implementation steps involved: 

  • Data collection

  • Model building

  • Linking of the program to the plant's Information (PI) system
  • Online optimisation

  • Model and optimisation reviews with users

  • Training of users

The entire steam system was optimised, including the pump and compressor drivers, steam production from the boilers and heat-recovery steam generators, as well as electrical production from the gas turbines and turbo generators. This led to substantial operating cost savings. Additional savings were generated through the identification of wasted steam and operating problems, as well as through offline "what-if" engineering studies to investigate alternative utility system configurations.

The Tarragona refinery processes eight million tpy of crude oil and is typically a very large energy user with several degrees of freedom. Manipulating these degrees of freedom using a cost-based optimisation program results in significant savings and requires only a small investment. This is particularly important within deregulated electricity markets. Since the electrical system poses one of the main economic trade- offs with a steam system, electricity deregulation makes it harder to operate overall combined systems at a minimum cost.

To successfully implement the optimization recommendations, a operator-oriented, well-implemented and understood tool is needed. Operators are generally only concerned with the unit(s) under their direct responsibility and not with refinery-wide energy cost reductions. Frequently, more than one person is responsible for the site (serving different areas), which can make it difficult to co-ordinate overall energy cost-reduction strategies. Also, utility systems are continuously evolving, and a lack of sensors can involve either estimating or calculating non-measured consumptions with modelling systems. Furthermore, utility systems have several constraints, usually originating from the operations side. Finally, it is important to note that the unattended convergence of a refinery-wide utility system optimiser is not a minor issue due to its complexity, especially when energy costs across the entire facility are considered on an hourly or daily basis.

All of these issues have been addressed successfully at the Tarragona refinery by the online steam management software. Its implementation has allowed the refinery to be more energy efficient and has reduced its overall utility system operating costs by improving performance in four ways:

  • Monitoring: the program monitors the entire steam, boiler feed water and condensate system, highlighting any problems. For example, significant changes in steam flows are flagged so that operators can quickly determine what has changed and alert those responsible for the change. This can reduce the chances of a refinery or individual process plant shutdown. The program also monitors equipment performance. For example, gas turbine performance can be tracked and maintenance scheduled at the most economical time
  • Optimisation: the program optimizes the entire steam system, including the pump and compressor drivers, the steam production from the boiler and heat-recovery steam generators, as well as electrical production from the gas turbines and turbo generators.
  • "What-if" engineering studies: the program is used routinely to study the benefits of making both small and complex changes to the operation or equipment of the steam system. Savings are found by comparing a given base case to the optimised case that includes the proposed change. Examples of "what-if" studies include evaluating turbine/motor switches, building a new plant, and scheduling utilities for a refinery-wide shutdown. On start-up, effective, accurate planning using the tool can save plant downtime, thus building the most economic project and achieving projected cost savings
  • Auditing and accounting: the program's data validation techniques can accurately account for steam usage and track down any waste and inefficiencies. The steam management software also allows for the online tracking of performance, so these savings can be maintained and documented properly.

Implementation description

As previously mentioned, the implementation steps involved: data collection; model building; linking of the program to the PI system; online optimisation; model and optimisation review with users; and training of users.

The Tarragona refinery shares its utility system with a neighbouring olefins plant. A complete model of this system was built, featuring the entire steam, boiler feed water (BFW) condensate and power system. Steam is generated in several units, including conventional boilers, heat-recovery steam generators and two cogeneration units.

ptq1

The five steam pressure levels were considered and all the units looked at in great detail. Detailed efficiencies curves of the biggest turbines were included in the model and adjusted continuously with online validated data.

Optimisation

The program features mathematical models and built-in optimisation routines that make it possible to calculate how to run the steam and electrical systems at a minimum overall cost while still meeting the required plant steam demands and other constraints.

The software determines which boilers or steam generators should make incremental steam and which turbines or letdown valves will most efficiently let the steam down between pressure levels. It uses a successive quadratic programming (SQP) optimiser, which is grouped into four levels:

  • Level 1: includes the pressure control-related devices; boilers, letdown valves and vents are optimised to minimise cost
  • Level 2: adds the optimisation of other continuous variables, including turbo generators and extraction/ induction/condensing turbines
  • Level 3: adds turbine-motor switching optimisation (ie, discrete variables)
  • Level 4: optimises variables that are potentially unsafe or affect process yield.

A well-running model is generally run at level 3, with an occasional run at level 4 to evaluate potential operational changes. The program's objective function is to optimise the total operating cost of the system, which is:

Operating cost = total fuel cost + total electricity cost + _ inlet costs

The SQP optimiser's job is to minimise this objective function, subject to operating constraints in the system. Total fuel cost is determined by the fuel use of each boiler and combustion turbine, multiplied by their respective fuel prices. Total electricity cost is determined by the net electrical use of each motor, load and generator, multiplied by their respective electricity prices. The model takes into account the fact that electricity prices vary throughout the day.

Inlet costs normally include charges for demineralised water coming into the system, but can cover other arbitrary costs too.

Practical issues

Since the program relies on user input, proper training of the operating personnel using the Repsol Tarragona model was essential. Input from the operators during and after the training helped to improve the way information is displayed.

When analysing the optimisation recommendations, a foreman with coverage of the whole refinery, utilities and olefins units was chosen to coordinate the implementation on a daily basis.

In case a sensor does not exist or has failed temporarily, the program uses calculated or estimated data. Usually, the main meters needed for optimisation are: cogeneration (steam flow rate), boilers (steam flow rate), letdown valves, vents, flow rates for induction/extraction/condensing turbines and on-off status for turbine motors. Some turbine-motor statuses are updated manually, but an improvement is under way to automate the capture of on-off statuses from the PI system.

Reports

The Excel custom report provides a familiar environment for users to view information concerning the simulation and optimisation of the system. Figure 1 shows an example of a generated report. In the worksheet shown, steam generation and fuel consumption are reported both for the current values and the optimised ones.

Data comes to Excel directly from the model. As the steam management program is built around .NET technology, it can communicate seamlessly with Excel.

Utility system monitoring

As mentioned earlier, significant changes in steam flows (as well as water flows, temperatures and pressures) are reported so that operators can quickly determine what has changed and alert those responsible, which reduces the chances of a refinery or individual process plant shutdown. Trends of the different sensors can also be viewed with the model.

"What if" engineering studies are carried out to evaluate changes (ie, equipment shutdown) to the utility system and assess their technical and economic impact.

Audit and accounting

By auditing the energy system, imbalances can be identified and reduced. The steam management program helps to locate wasteful steam usage. Balloons are used to illustrate the measurement of steam balance closure. They perform the algebraic summation of all the flows for streams entering and leaving the balance. Since there is a value for the flow of every stream, the total should be 0.0 (all the steam that comes in must go out). If the net balance is not 0.0, some meters or estimated equipment flow rates are erroneous, or there is steam leaving or entering the balance that has not been accounted for. The balloons dynamically show meter errors by changing in size and colour, depending on the amount of steam imbalance. Balloons are placed where there is a chance of a closed mass balance.

A closed mass balance is formed by a group of flow meters, equipment with associated meters, or a combination of equipment and flow meters. Balloons are used for two main purposes:

  • To validate steam flow data: if all of the flows in a balance continually add up to near zero, the flow data can be relied on for evaluating the value of production and use, and waste can be eliminated; if the balance does not add up to near zero, meters could be wrong or equipment steam flow rates may be different to those estimated and there might be significant waste.
  • To store model errors, for use when comparing one case to another (ie, the actual operation against the optimised one).

Economic benefits

In order to precisely evaluate the economic benefits of the steam management program, the following real-time test was carried out:

  •  During the first month, the tool was executed online but no optimisation actions were taken

  • During the second month, the optimisation suggestions were obeyed progressively
  • During the third month, the optimisation suggestions were followed on a daily basis.

 More than a 4% reduction in total energy costs related to the steam system were achieved by following the optimisation recommendations. At the time of going to press, the system was undergoing further improvements.

The program proved to be a robust optimizer and is well suited to routine operation. Themodel helps evaluate "what-if" scenarios that include changes to the utility systems. Auditing and accounting of the steam and BFW help reduce wasted steam and identify imbalances. Finally, continuous monitoring prevents plant upsets and helps to quickly identify steam wastage. 

It is important to emphasise the high involvement and motivation of the plant operators since the beginning of the software implementation. Co-ordination among plant areas is critical if the proposed optimisation recommendations are to be implemented successfully, so management involvement is crucial too. User acceptance and widespread employment are also key to success. Repsol is currently looking at ways of using the program in several other locations. 

Diego Ruiz Massa is manager of Soteica Europe SL's office in Barcelona. He holds a doctorate degree in chemical engineering from Universitat Politècnica de Catalunya. Email: diego.ruiz@soteica.com

Carlos Ruiz García is the advanced control and optimisation manager of Soteica Europe SL and is a tenured professor of chemical engineering at the Universidad Tecnologica Nacional. Ruiz Garcîa received his chemical engineering degree from the Universidad Tecnologica, Rosario, Argentina and MSc and PhD degrees in chemical engineering from the Universidad del Sur, Bahia Blanca, Argentina. Email: carlos.ruiz@soteica.com

David Nelson is a principal at Nelson & Roseme Inc. He previously worked at Chevron before helping found Nelson & Roseme Inc in 1997. Nelson has a PhD in chemical engineering from the University ofMassachusetts.
Email: david.nelson@nelson-roseme.com

Gary Roseme is a principal at Nelson & Roseme Inc, with 24 years' experience in the oil industry. Roseme has a MS from the University of California at Berkeley in mechanical engineering.
Email: gary.roseme@nelson-roseme.com

Manuel Lázaro Meléndez is a chemical engineer with 20 years' experience in the petrochemical industry (Repsol Petróleo SA). Email: mlazarom@repsolypf.com

María Sartaguda Pardos has four years' experience working for Repsol Petróleo SA as a process engineer. Sartaguda Pardos recently moved to the purchasing department in Madrid.
Email: msartagudap@repsolypf.com

Industries

  • Oil & Gas Downstream

    The oil & gas downstream industry has been facing an increasing number of challenges in recent years. These include the changing characteristics of the feedstock to be processed, aging of process facilities and equipment, rising cost of energy, lack of skilled plant operators who can run a refinery safely and efficiently, and the ever-changing requirements from both the market and the customer.

    Over the years, Yokogawa has partnered with many downstream companies to provide industrial solutions focused on solving these challenges and problems. Yokogawa's VigilantPlant solutions have helped plant owners to achieve maximum profitability and sustainable safety within their plants.

    See More
  • Refining

    In the ever changing marketplace, refineries are seen not only as crude processing units but also as profit centers. At the same time, there is a keen awareness of the need for safety at such facilities. A total production solution that encompasses planning, scheduling, management, and control is required to achieve long-term goals for profitability, efficiency, and environmental protection. With years of expertise in the automation field, Yokogawa can bring you affordable total solutions for improved operability and a cleaner world.

    See More

Top