Monitoring Mercury Control in Coal Fired Power Plants using ORP

Ściągnij (361 KB)


Current trend for increasing mercury awareness throughout the public sector has caused the government to take action. Recently, the Environmental Protection Agency (EPA) has focused their efforts on controlling mercury levels produced in various coal fired power plants. Based on information from several case studies, the EPA developed the Mercury and Air Toxics Standards to cut back mercury emissions. The most popular technology utilized by coal plants to meet the new standards is a scrubber which cleans the off gas from the combustion process. ORP sensors can further monitor the effluent from these scrubbers to ensure optimal mercury emission levels are achieved. By closely monitoring the mercury concentrations in the effluent, plant managers will be able to easily confirm their plants are meeting the EPA's standards.


Coal fired power plants produce 50% of the 5500 tons of mercury released into the environment each year. Mercury exists in three forms throughout the world: metallic element, inorganic salts, and organic compounds (methyl mercury, ethyl mercury, and phenyl mercury). Since elemental mercury has a low boiling point it can travel long distances and deposit into the soil and water. The elemental mercury is then transformed by microorganisms into methyl mercury. Methyl mercury then biomagnifies as it moves up the aquatic food chain. Human exposure is primarily connected to the consumption of contaminated fish.

In order to better understand the effects of consuming fish that have consumed methyl mercury, three epidemiological studies were completed. The studies examined children exposed to methyl mercury in utero at concentrations similar to the current U.S. exposure levels. The first study observed that children born to women with maternal hair mercury concentrations greater than 6μg/g exhibited a 3 point decrease in their IQ score. The other two studies' verified these results. The studies also found that delayed brainstem auditory responses occurred at levels of 3.2μg/L of mercury in cord blood. Recent data illustrates that cord blood mercury concentrations have increased 70% since the 2003 studies. In the Faroes case study from 2004, the researchers found fetal blood mercury levels were 30% higher than their mother's blood concentrations. Even though there is no evidence validating a threshold blood mercury concentration that has no adverse effect on the brain's cognition, the EPA set a benchmark dose level (BMDL) of 58μg/L. This level corresponds to the lower limit of the 95% confidence interval. It is important to mention that the studies observed developmental effects at levels of 1 ppm mercury in hair, or 5.8μg/L of mercury in cord blood. The National Health and Nutrition Examination Survey recently discovered that 15.7% of American women have total blood mercury concentrations greater than 5.8μg/L. Based on this data, between 316,588 and 637,233 babies are born with cord blood mercury levels greater than 5.8μg/L. This number continues to increase every year.

The Faroes study examined the effects on a person's IQ when mercury concentrations are doubled. The lowest concentration tested was 4.84μg/L, and then doubled from there. The test results showed that doubling of concentrations produced a range of IQ points that averaged a 2.4 point decrease. The test then calculated the costs associated with the cognitive effects of mercury exposure. It determined that every IQ point lost among men resulted in a 1.931% decrease in lifetime earnings. In women there was a decrease of 3.225% total lifetime earnings for every IQ point lost. With the increases in blood mercury level, future generations will continue to be affected.

On December 16, 2011, the Environmental Protection Agency (EPA) put into law a national Clean Air Act emission requirement for coal and oil burning power plants referred to as the Mercury and Air Toxic Standards (MATS). It will affect Electrical Generating Units (EGUs) larger than 25 megawatts and EGUs that produce electricity for sale and distribution to the national grid. This regulation will reduce air pollution from coal and oil burning EGUs by implementing the numerical emission limits of the following compounds:

• Mercury(Hg)

  • Particulate matter(PM)
  • Hydrochloric acid(HCl)
  • Hydrofluoric acid (HF) for oil burning EGUs only 
Past numerical limits for dioxin and furan in new and existing coal and oil burning EGUs are being replaced by work practices requiring annual performance tests and tune-ups. Oil burning EGUs can show compliance for HCl and HF by limiting the moisture content of the oil used. To ensure compliant performance, the EPA requires semi-annual reports and initial notifications of compliance for each unit no later than 120 days after the facility has become subject to MATS. The regulation also requires detailed records to be kept for: each instance that an EGU did not meet an emission limit or work practice standard, daily hours of operation for each EGU, results of all performance tests, and notifications of planned performance testing. If continuous emissions monitoring systems (CEMS) are being used to measure compliance quarterly, monitoring summaries should be submitted. The following options for Coal-burning EGUs mercury emission limit compliance monitoring is broken down in Figure 1. Implementation deadlines are dependent on which state the plant is located in. Table 1 provides the limits for the coal-burning power plant emissions.  


There are three forms of Mercury present in coal-burning power plant systems: particulate mercury, oxidized mercury (Hg2+), and elemental mercury (Hg). Only particulate and oxidized mercury are captured by existing Air Pollution Control Devices (APCDs). One method for mercury control is Activated Carbon Injection (ACI) and particulate control. Another is wet Flue Gas Desulfurization (FGD) scrubbers and Selective Catalytic Reduction (SCR). An electrostatic precipitator (ESP) also helps to capture particulate matter. Both ACI and FGD methods use Oxidation Reduction Potential (ORP) sensors to monitor the oxidation of the mercury.

After the combustion reaction in the boiler, the byproducts released move through an electrostatic precipitator (ESP) where some particulates are filtered out. The byproduct of combustion is called flue gas. Flue gas contains water vapor, carbon dioxide, nitrogen, particulates, oxygen, carbon monoxide, nitrogen oxide, hydrocarbons, sulfur oxide (SOs), and mercury. After the flue gas passes through an ESP, the gas goes into a wet FGD scrubber. A scrubber is composed of technologies used to remove "scrub" (SO2 and particulates) from the stack emissions of power plants. An important part of the scrubbing process is known as stripping. Stripping is the dissolution of gas from the fumes into a liquid composed of water and a calcium additive (most likely limestone). Random packing can be used inside the scrubber to force the gas to form smaller bubbles that float up while liquid flows down. This provides for optimum contact of liquid with the gaseous bubbles. The liquid traps the contaminants in the gas and allows the clean gas to escape. The higher the gas floats the cleaner the gas is and the less liquid it contacts. Figure 2 below illustrates the scrubbing process.


The stripped contaminated gas is collected, concentrated, and reduced at the bottom of the scrubber with the liquid from the sprayers. After limestone reacts with the SO2 gas, a liquid form of calcium sulfite or calcium sulfate is produced. The liquid sludge will settle out and the water will be reused. The wet solid sludge is an off- white color with a five to ten percent solid content. Since some of the solid is in the form of fly ash, some systems will use fly ash removal systems. After determining the ratio of calcium sulfite to sulfate the best treatment process can be determined. The amounts of calcium sulfite to sulfate vary depending on the process and the sorbent material. Sludge with high concentrations of sulfite has to be treated because it is thixotropic. Thixotropic compounds appear to be solid, but when vibrated or agitated will liquefy. Because of this, calcium sulfite does not filter very well. Forced oxidation, dewatering, and/or fixation/ stabilization are all treatments that could be used. After being treated, most scrubber sludge is stored in landfills and holding ponds. Some products come out of the treatment process like gypsum; which is used in wallboard production1. The entire sludge treatment process is illustrated in Figure 3.


Soluble oxidized mercury will precipitate in the FGD scrubber allowing it to be separated easily. The scrubber also helps with the emission control of acidic gases produced in the combustion process. In addition, a fabric filter can help capture particulate matter of toxic metals including mercury. However, even with all of the APCDs, mercury emissions still may not be reduced to required levels. Therefore, ORP and temperature sensors are needed to monitor and regulate the efficiency of the oxidation process.

Oxidation Reduction Potential (ORP) is a measure of the strength of the oxidizing agent or the reducing agent of a solution. The reducing agent donates electrons while the oxidizing agent acquires electrons. This transfer of electrons is called an oxidation-reduction (redox) reaction. ORP measures the ratio of electron activity for the oxidizing and reducing species in a solution. This ratio indicates the solutions ability to oxidize or reduce another substance. It does not determine the concentration of the predominant oxidizing or reducing agent. The speed of the ORP sensor's response varies depending on the concentration of the redox system; high concentrations are faster to respond than lower concentrations. Maintaining stable ORP values will prevent mercury re-emission. A positive ORP reading of the slurry reduces re-emission of mercury because elemental mercury will be more easily oxidized into Hg2+.

There are other factors in the coal burning process that can affect the oxidation process. One of these is coal with a higher chlorine count which produces less elemental mercury. Another is unburned carbon which can absorb vapor phase mercury to form particulate bound mercury. Oxidation of Mercury happens between the temperatures of 850 degrees Fahrenheit to 300 degrees Fahrenheit. Finally, the temperature gradient across an air heater can affect oxidation. Table 2 shows the state of mercury at various ORP measurement levels.


Yokogawa Solutions

Depending on installation requirements there are a couple of different options that can be considered.


FLXA21 2-wire 24VDC pH/ORP Transmitter

PH450G 4-wire 110 VAC pH/ORP Analyzer

(1) PR10 Retractable with combination electrode

Yokogawa's Hot-Tap retractable allows for removal from the process without interruptions or shut- downs. Without any special tools that PR10 can be retracted safely from the process up to 5 bar. The retractable is equipped with a integrated protection cage and a built in scrapper to avoid contamination of the fitting.

Sensor Selection Options

(A) Traditional Reference system: The Hamilton EasyFerm Plus VP, part number 238999-3067, is an all-in one design that will measure pH, ORP and temperature at the same time.

(B) Differential Cation Reference System: The SC24V offers benefits over the traditional reference system since there is no junction to be clogged or coated, no electrolyte to be depleted, and no Ag/AgCl reference element to become poisoned. The SC24V will measure pH, ORP and temperature at the same time.

For more information on differential cation reference system, please refer TechNote TNA1304 or Application Note PH-A-011.

(2) FU20 or FU24 pH/ORP Combination electrode

Yokogawa's family of all-in-one wide body combination sensors hold four separate measuring elements in one unbreakable and chemical resistant body. The FU20 and FU24 will measure pH, ORP and temperature at the same time. The construction of the Ag/AgCl reference system with double junctions and polymerized saturated KCL fill solution along with the Ag+ ion trap extend the life of the probe. This option allows for easy installation with either a 3⁄4" NPT or 1" NPT threaded process connection.


EPA is now regulating mercury, as well as other pollutants produced from flue gas, to reduce pollution and prevent health issues. Coal and Oil-burning EGUs larger than 25 megawatts will have to monitor emissions and take the necessary actions to reduce the levels of mercury and air toxics. Mercury emission limits were set for new, existing, and different ranks of coal which can be found in Table 1. There are two methods of compliance: continuous monitoring and periodic testing. Scrubbers are currently used to treat the flue gas produced from coal combustion. Scrubbers can efficiently reduce emissions by maintaining optimum ORP ranges to prevent mercury re-emission. Yokogawa provides several types of ORP sensors that could be used[ monitoring ORP in power plants to reach compliance with MATS.

Call to Action

For more information on the technologies discussed in this paper and how coal power plants can implement the devices into the process contact Yokogawa Corporation of America at the following links:

Yokogawa Corporation of America

2 Dart Road, Newnan, GA 30263-0928 Phone: 770-254-0400 Fax: 770-254-0928

12530 W. Airport Blvd., Sugar Land, TX 77478 Phone: 282-340-3800 Fax: 281-340-3838

Yokogawa Canada, Inc.

Bay 4, 11133 40th Street SE, Calgary, AB T2C 2Z4 Phone: 403-258-2681 Fax: 403-258-0182

Yokogawa de Mexico, SA de CV

Av. Urbina No. 18
Fracc. Parque Industrial Naucalpan Naucalpan de Juarez
Estado de Mexico, C.P. 53489
Phone: (55) 5955-7400 Fax: (55) 5955-7417


Pictures and Figures

Figure 1

United States of America. Environmental Protection Agency. Fact Sheet: Mercury and Air Toxic Standards. N.p., n.d. Web. 8 July 2014.

"Mercury and Air Toxics Standards (MATS) for Power Plants." EPA. Environmental Protection Agency, 26 Nov. 2012. Web. 08 July 2014.

Figure 2

Yokogawa Corporation of America. Application Note: Sulfur Dioxide Scrubber: PH Control. AN 10B01B02-23E- A. N.p.: Yokogawa, n.d. Print.

Table 1

United States of America. Environmental Protection Agency. Fact Sheet: Mercury and Air Toxic Standards. N.p., n.d. Web. 8 July 2014.

"Mercury and Air Toxics Standards (MATS) for Power Plants." EPA. Environmental Protection Agency, 26 Nov. 2012. Web. 08 July 2014.

Table 2

"ORP as a Predictor of WFGD Chemistry and Wastewater Treatment - POWER Magazine." POWER Magazine. N.p., 01 July 2013. Web. 08 July 2014.


"User Guidelines for Waste and Byproduct Materials in Pavement Construction." US Department of Transportation Federal Highway Administration. N.p., 23 Apr. 2012. Web.

Cooper, Pe, Bcee Golder Associates, Inc., Ivan, and Ron Ruocco, PE, Golder Associates, Inc. "Wastewater Treatment for Flue Gas Desulfurization (FGD) at Electric." Wastewater Treatment for Flue Gas Desulfurization (FGD) at Electric Power Plants (n.d.): n. pag. Web. 8 July 2014.

Controlling Mercury Emissions from Coal-fired power plants Leigh Energy Update February 2010, Vol. 28.No. 1 (2010): 1-2. Leigh Energy Update. Feb. 2010. Web. 8 July 2014.

Dartmouth Engineering School. "Flue-gas Desulferization- Scrubbers." Dartmouth Engineering School. PowerPoint.<>

Grandjean, Philippe, Hiroshi Satoh, Katsuyuki Murata, and Komyo Eto. "Abstract." National Center for Biotechnology Information. U.S. National Library of Medicine, 08 June 2010. Web. 08 July 2014.

"Edit Content Edit Classification Publishing Workflow Featured Settings Delete Content Minamata Disease." Minamata Disease. N.p., 14 Dec. 2009. Web. 06 July 2014.

Plataforma SINC. "Exposure To Low Doses Of Mercury Changes The Way The Arteries Work." ScienceDaily. ScienceDaily, 27 October 2008. .

Wu, Cheng-Li, Yan Cao, Cheng-Chun He, Zhong-Bing Dong, and Wei-Ping Pan. "Study of Elemental Mercury Re- emission through a Lab-scale Simulated Scrubber." Fuel 89.8 (2010): 2072-080. Web. 8 July 2014. .


  • Energetyka

    In the mid 1970s, Yokogawa entered the power business with the release of the EBS Electric Control System. Since then, Yokogawa has steadfastly continued with the development of our technologies and capabilities for providing the best services and solutions to our customers worldwide.

    Yokogawa has operated the global power solutions network to play a more active role in the dynamic global power market. This has allowed closer teamwork within Yokogawa, bringing together our global resources and industry know-how. Yokogawa's power industry experts work together to bring each customer the solution that best suits their sophisticated requirements.

    Zobacz więcej

Powiązane produkty i rozwiązania

  • Differential pH/ORP Sensors

    The cation differential pH and ORP sensors were designed for difficult applications where conventional sensors are ineffective. These include measurements such as brine solutions to applications as diverse as electrolysis processes and cheese manufacturing.

    Zobacz więcej
  • EXAtrac RF20 Pneumatic Retractable

    The pneumatic retractable holder EXAtrac RF20 (Extrac 810 and 820) is made for installation of 12mm sensors on tanks or pipelines where the sensor has to be removed without interruptions or shutdowns and in the hash applications where frequent cleaning is of vital importance for a good pH measurement.

    Zobacz więcej
  • Flow/NPT Fittings FF20/FS20

    Yokogawa has invested considerable design and development time in producing a full range of fittings with particular emphasis on designs that reduce installation and maintenance time and consequently save operation costs.

    Zobacz więcej
  • Hot-Tap Holder PR10

    On-line measurements often present extra challenges, especially when routine maintenance is required. The PR10 is ideally suitable for applications where the sensors must be removed without interrupting or shutting down the process. Without any special tools the PR10 can be retracted safely from the process at pressures up to 5 bar (72 psi). Using the PR10 allows us to place any dissolved oxygen sensor that has a PG13.5 connenction into a retractable assembly.

    Zobacz więcej
  • Immersion Holder FD20

    The immersion fittings are designed for either pH or ORP (Redox) measurements in tanks, open vessels and drains. They have a "hoisting cable" for easy maintenance.

    Zobacz więcej
  • Personal Handheld Meter PH71/PH72

    The PH71/PH72 pH and/or ORP meter is a Compact, Easy-to-use, Drip proof – Ideal for Field Use. Features "One-Touch Calibration" and Temperature Compensation. Laboratory-Grade Intelligent pH Meters – Sized and Priced to Fit in Your Pocket

    Zobacz więcej
  • pH/ORP Buffer Calibration Solutions

    Buffer solutions are needed as an indispensable tool for maintaining an accurate pH measurement. Buffer solutions are used as references points for calibration and adjustment of pH measurements to compensate for aging and deterioration.

    Zobacz więcej