Austria AT   
LL50A
Control Devices

Parametereinstellungssoftware LL50A

Die Parametereinstellungssoftware LL50A wurde entwickelt, um Parameter, Ladder-Programme und Ähnliches für UT-Advanced-Regler mit digitaler Anzeige über einen Computer zu entwickeln und einzurichten. Die Ladder-Programme können während der Kommunikation mit den Reglern feineingestellt und überwacht werden.

  • Parametereinstellfunktion
  • Feineinstellfunktion
  • Ladder-Programm-Entwicklungsfunktion
  • Netzwerkprofil-Erstellungsfunktion

Details

Parametereinstellfunktion

Parameter Setting Display

Parameter zur Regelung der Regler-Funktionen können ganz einfach eingestellt werden:

Regler-Modell, Regler-Modus (einschleifige Regelung, Kaskadenregelung, Schleifenregelung mit PV-Umschaltung etc.), universelle Eingang/Ausgang-Funktionen, Konfigurationsparameter und weitere Parameter.

Zum Tuning nutzen

Tuning Display

Wird zum Einstellen der PID-Parameter eines Reglers verwendet. Zeigt den gemessenen Eingangswert, den Einstellwert und den Regelungsausgangswert als Trenddiagramm auf einem PC-Monitor an und ermöglicht die Änderung von PID-Parametern, AUTO/MAN-Umschaltung, die Änderung des Regelausgangs im manuellen Betrieb etc.

Ladder-Programm-Entwicklungsfunktion

Ladder Program Building Display

Sie können Ladder-Sequenzprogramme erstellen und Ladder-Programme überwachen.

Netzwerkprofil-Erstellungsfunktion

Mit dieser Funktion können Sie ein elektronisches Gerätedatenblatt für die PROFIBUS-DP-Kommunikation erstellen.

Über busbasiertes USB-Kabel

Via Bus Powered USB Cable

Stellen Sie Parameter auch ein, wenn der Regler nicht mit Strom versorgt wird.

Über Ethernetkommunikationsanschluss

Via Ethernet Communication Connector

Über eigenen Adapter

Via Dedicated AdapterKann bei Anschluss an das Regelpult verwendet werden.

  • Anwendbare Regler: UT55A, UT52A, UT35A, UT32A
  • Anwendbare Betriebssysteme: Windows XP/Vista
  • Kommunikationsmethode: USB 1.1

Über RS-485-Kommunikationsanschlüsse

Via RS-485 Communication Terminals

Publikationen

I installed LL50A on my PC but I can't open communications.
(ns-faq-ut-2072-connect)
Confirm that there is a proper USB connection. If there is no problem with the connection, check whether the USB driver is installed correctly on the PC.
What do "upload" and "download" mean with the LL50A?
(ns-faq-ut-2084-term)
Upload means to read data on the LL50A from a controller. Download means to write data from the LL50A onto the controller.
I'm creating setup data on the LL50A. I want to write the data on the controller, but should I do an upload or a download?
(ns-faq-ut-2101-setting)
To write the data from the PC to the controller, do a download.
I can't select Tuning, Register monitor, or Ladder program monitor from the LL50A monitor menu.
(ns-faq-ut-2105-setting)
Close all windows open in the lower right of the screen, such as the parameter setting window.
Does a communication cable come with the LL50A?
(ns-faq-ut-2107-spec)
The LL50A comes with a dedicated USB cable, and a dedicated adapter for attaching to the main unit front panel.
Can you tell me the model of the cable that comes with the LL50A parameter setting software?
(ns-faq-ut-2149-select)
The model is LL50A-00 (parameter setting software).
While setting data on the LL50A, the MODE parameter item doesn't appear.
(ns-faq-ut-2151-setting)
MODE (operation mode) related parameters do not appear.
Can I purchase an English version of the LL50A setting tool?
(ns-faq-ut-2161-select)
The LL50A supports Japanese and English. The installer detects the language of the OS automatically.
There are no operation keys on the /MDL DIN rail attachment model. How can I perform autotuning?
(ns-faq-ut-2188-setting)
Autotuning can be executed from the LL50A tuning monitor.
I installed the LL50A. I want to write the UT settings to a PC, but I get the following error message. "Failed to upload instrument information. Check the communication connection and conditions."
(ns-faq-ut-2190-setting)
When you install the LL50A, two icons are create on the desktop. To write settings, launch the Setting Tool by clicking its icon.
Can I switch the language of LL50A from Japanese to English?
(ns-faq-ut-2199-setting)
Yes, in version R6.02.01 and later.Use File>Settings>Language. If parameters are not displayed, install the latest version of LL50A.
Communication on the LL50 setting tool isn't working.
(ns-faq-ut-2211-setting)
Check the following. Whether the dedicated cable is securely inserted into the adapter. The position of attachment to the front of the controller. In Device Manager, under Ports (COM and LPT), confirm that "Yokogawa USB Serial Port" ap...
I want to apply protection to a ladder program created on LL50A.
(ns-faq-ut-2212-setting)
You can protect it with a unique user password.
Can I use a commercially available USB cable for LL50A?
(ns-faq-ut-2242-connect)
No, please use the included cable when you purchase LL50A.
What’s the password I need to enter in LL50A to restore factory defaults on the controller?
(ns-faq-ut-2244-setting)
The password is UTAdvanced_INIT.
What’s the password I need to enter in LL50A to restore user defaults on the controller?
(ns-faq-ut-2245-setting)
The password is UTAdvanced_INIT_SET.
When reading UT data on LL50A, the DCU version of the system data is R0.00.00. Is that normal?
(ns-faq-ut-2250-spec)
Yes. For LL50A communication that uses the maintenance port, the DCU version is R0.00.00.
I'm editing a CC-Link communication profile on the LL50A. I want to add the UT32A-D type to the RS485 communication line, but the PV2 register symbol doesn't appear.
(ns-faq-ut-2168-setting)
Select Modbus slave device UT32D.
I purchased a DIN rail mount UTAdvanced series, but how should I configure it?
(ns-faq-ut-2165-spec)
Use the LL50A Parameter Setting Software, sold separately.
I want to perform cascade control of 2 temperature inputs on a single unit. Is there a model that can do that?
(ns-faq-ut-2193-select)
Yes, the UT75A + LL50A setting software (sold separately) can handle that.
When using the LL50A to create ladder programs, which ladder program edit mode should I use: "input ladder calculation," "output ladder calculation," or "user ladder"?
(ns-faq-ut-2030-program)
Generally you should create programs in "user ladder" mode. If needed, you can rewrite the input ladder and output ladder portions.
I'm creating ladder programs on the LL50A. I want to set input computed results to R.SP, but I see lots of digits are displayed after the decimal point of the data on the ladder monitor. Can I reduce the number of digits displayed after the decimal point?
(ns-faq-ut-2031-program)
The DATA register uses a 4-byte floating point number, therefore it displays a lot of digits. Try using the K or P registers, since they handle 2-byte integer data.
Can I disable ladder programs that I used?
(ns-faq-ut-2034-setting)
On the LL50A, change the system data's ladder sequence function from USE to DON'T USE. If not using the LL50A, initialize the main unit.
My LL50A ladder program monitor does not start.
(ns-faq-ut-2036-program)
It won't start while the system data or parameter setting screen is displayed. Close those screens and restart.
A ladder program that I wrote doesn't work properly.
(ns-faq-ut-2037-program)
Check the operation of the program on the LL50A ladder program monitor.
Can I change the temperature controller profile information for CC-Link communication?
(ns-faq-ut-2068-spec)
You can change it if it is in a user profile (profile no. 0).To create a user profile, use the LL50A network profile tool.
With the LL50A and UTAdvanced, can I perform RS-485 communications without a dedicated cable?
(ns-faq-ut-2051-connect)
Yes, if using a UTAdvanced series instrument with the RS-485 communication option. Set the RS-485 protocol on the main unit to 8 (MBRTU: Modbus RTU). The initial value is 8. Select RS-485 in the LL50A communication execution screen, and make the comm...
How can I display parameters that aren't displayed in the LL50A parameter setting software?
(ns-faq-ut-2052-soft)
If the LL50A's display setting is not PRO, some parameters won't display. Change the LL50A's display parameter as follows: Display > Parameter > Display level > Professional. The LL50A's display level must be set separately f...
After changing the UT's SP values from the MELSEC via CC-Link, when I change the SP value on the UT main unit, I can't change to the same value as before from the MELSEC.
(ns-faq-ut-2026-connect)
As for individually writing parameters via CC-Link, changing OUT area values constitutes a write request. In your case, since the OUT area value hasn't changed from the previous value, the SP value is notoverwritten. As a fix, periodically copy t...
Can I convert GREEN series (UT300/UT400/UT500/UP500) parameters for use with the UTAdvanced series?
(ns-faq-ut-2060-soft)
Yes, you can use the GREEN-UTAdvanced parameter data conversion tool (available as free download). Using the LL100/LL200 parameter setting tool, save the GREEN series parameters to a file, convert them using the conversion tool, then apply the settin...

Downloads

Bedienungsanleitungen
Datenblätter
Software

Möchten Sie weitere Informationen über unsere Mitarbeiter, Technologien und Lösungen?

Kontakt
Top