Standalone MW100
Hinweis: Dieses Produkt wurde eingestellt am Sehen Sie sich dieses Ersatzprodukt an:

Industrial processes often employ multiple data acquisition systems to monitor the health of assets and facility infrastructure. These systems can be either standalone or built as nodes within a larger automation topology.

The MW100 is a scalable, high performance data acquisition and data-logging platform designed for standalone, networked, or PC-based operation under industrial operating conditions. It supports remote web-based configuration and monitoring. With its DIN rail design, it is often mounted in an enclosure or cabinet.

Details

"Smart Logging" - Anytime, Anyplace

The MW100 is a scalable, high performance data acquisition/data-logging platform designed for both PC-controlled and stand-alone operation under harsh operating conditions. Open Ethernet connectivity with web-based configuration and data monitoring functions allow MW100 to handle a wide range of monitoring and historical logging functions. See real time trends with your web browser from any PC and no special software. A full range of input/output modules handle all of your process inputs with fast measurement speed and high noise immunity for rock-solid performance.

MW100 Image

Anytime, Anyplace...

  • In a wide range of temperatures: -20 to 60° 1,2,3,4
  • Reinforced insulation: Between input terminal and case5 3700 Vrms (one minute) or 600 Vrms/VDC (continuous)
  • A wide variety of network functions: HTTP, FTP, DHCP, SNTP, E-mail, and others
  • DC power supply (12 V-28 V) option available

Smart Logging...

  • High speed measurement with a single unit (10 channels/10 ms or 60 channels/100 ms):
    Shortest measurement interval of 10 ms
  • Multi-interval: Enables mixing of three different measurement intervals in a single unit (measurement intervals can be set for each module)
  • Supports CompactFlash (CF) cards 6 of up to 2 GB Continuous data acquisition is possible on 60 channels at 100 ms for approximately ten days with a 2-GB card, or for three months on 60 channels at 1 s.
  • MATH function on the main module available with the /M1 option.
  • Collective data acquisition on 360 channels (via Modbus with the /M1 option)
  1. The operating temperature range for the input modules and main module. The operating temperature range of the output modules is -20 to 50°.
  2. Note that the power cord supplied with the main module differs depending on the operating temperature range (see the specifications on page 7). If the operating temperature range specification of the supplied standard power cord does not meet your requirements, we recommend that you select a screw-type terminal rather than the plug type for the main module power inlet, and supply your own power input cable.
  3. The operating temperature range of the AC adapter used with DC power supplies is 0 to 40°.
  4. Please consult with a representative for applications involving temperatures below -20°.
  5. The withstand voltage value with the MX110 input module. For the withstand voltage values of other input and output modules, please refer to the specifications for those modules (GS 04M10B01-01E).
  6. CF card not included (sold separately).

 

* Notice on Java Plug-in running in Web browser for MW100

 

A custom MW100 measuring system

A custom MW100 measuring system is comprised of three elements; the MW100 main module, MX Series input/output modules, and MX150 Series base plate. The system can be bench mounted as-is or DIN rail mounted for rack or panel installations. A DIN rail-mounting bracket is included with the MX150. 

The input/output modules, base plate, and accessories are all the same as those for the MX100 DAQMASTER series (AC adapter is for the MW100 only).

Input Modules

Input Modules 01

Name Model Number of channels Shortest measurement interval Description
10 channel pulse input module  MX114-PLS-M10 10 100 ms Non-voltage contact /Open collector
(10,000 sample/sec integration speed)
30 ch general purpose input module
with 500 ms scan speed
 
MX110-VTDL30 30 500 ms Clamp terminal, DCV/TC/DI
MX110-VTDL30/H3 30 500 ms M3 screw terminal, DCV/TC/DI

Input Modules 02

Name Model Number of channels Shortest measurement interval Description
Universal Input Modules MX110-UNV-H04 4 10 ms DC voltage, thermocouple, 3-wire RTD, DI (non-voltage contact, Level (5 V logic)). Mixed input allowed.
MX110-UNV-M10 10 100 ms DC voltage, thermocouple, 3-wire RTD, DI (non-voltage contact, Level (5 V logic)). Mixed input allowed.
4-Wire RTD and Resistance Input Module MX110-V4R-M06 6 100 ms DC voltage, 4-wire RTD, 4-wire resistance, DI (non-voltage contact, Level (5 V logic)). Mixed input allowed.
Strain Input Modules MX112-B12-M04 4 100 ms Built-in bridge resistance of 120 ohm
MX112-B35-M04 Built-in bridge resistance of 350 ohm
MX112-NDI-M04 For connection with an external bridge head and strain gauge type sensor (NDIS connector))
5 V Digital Input Module MX115-D05-H10 10 10 ms Non-voltage contact, open collector, and Level (5 V logic). Mixed input allowed.
24 V Digital Input Module MX115-D24-H10 10 10 ms Level (24 V logic), Vth = 12 V

Output Modules

Output Modules

Name Model Number of channels Ouput update interval Description
Analog Output Module MX120-VAO-M08 8 100 ms Allows mixed voltage (±10 V) and current (4-20 mA) output
PWM Output Module MX120-PWM-M08 8 100 ms Pulse width modulation output module
Digital Output Module MX125-MKC-M10 10 100 ms "A" contact (SPST)

Base Plate

Base Plate

Base plates available for all configurations, from 1 to 6 input/output modules. 

When used for the MW100/MX100, you must replace the attachment with the one that comes standard with the MW100/MX100.

Accessories

Accessories(Connector Covers/AC Adapter)Connector Covers
Connector covers for open slots 

AC Adapter (772075)
AC adapter for the DC power model.
Operating temperature range: 0 to 40°
*Only for the MW100

Accessories (Removable Terminal)

Accessories (Removable Terminal) 01

All input/output terminals are removable except for those of the MX112-NDI-M04. If multiple terminals are prepared ahead of time, no re-wiring is needed between measurements.

Accessories (Removable Terminal) 02

Model Description
772061 Screw (M4) terminal block (RJC (reference junction compensation) included).
For use in combination with 772062. Compatible with MX110-UNV-M10, MX115-D05-H10, and MX115-D24-H10.
772062 Connection cable between input modules and the screw terminal block.
Compatible with MX110-UNV-M10, MX115-D05-H10, and MX115-D24-H10.
772063 Plate with clamp terminals (RJC included).
Compatible with MX110-UNV-M10, MX115-D05-H10, and MX115-D24-H10.
772064 Clamp terminals. Compatible with MX110-UNV-H04.
772065 Clamp terminals. Compatible with MX120-VAO-M08, MX120-PWM-M08, and MX125-MKC-M10.
772067 Plate with clamp terminals. Compatible with MX110-V4R-M06.
772068 Plate with clamp terminals (Built-in bridge resistance of 120 ohm). Compatible with MX112-Bxx-M04.
772069 Plate with clamp terminals (Built-in bridge resistance of 350 ohm). Compatible with MX112-Bxx-M04.
772080 Plate with screw (M3) terminal (RJC included).
Compatible with MX110-UNV-M10, MX115-D05-H10, and MX115-D24-H10.
772081 Plate with clamp terminal for current with 10 ohm built in bridge resistance, applies to MX110-UNV-M10
772082 Plate with clamp terminal for current with 100 ohm built in bridge resistance, applies to MX110-UNV-M10
772083 Plate with clamp terminal for current with 250 ohm built in bridge resistance, applies to MX110-UNV-M10

Multi-Access

The MW100 can be connected to multiple PCs at the same time. This allows monitoring and sharing of measured data by multiple users. A login function is included to enable assigning of access rights.

Measurement information shared

Measurement information shared

Measured data shared

Measured data shared

* Mail server required.

Acquire up to 360 Channels in One System

Acquire up to 360 Channels in One SystemA large data acquisition system of up to 360 channels can be assembled using multiple MW100s and standard MODBUS TCP Ethernet communications. When equipped with the /M1 math option, the MW100 can acquire up to 300 channels of external data from additional MW100 units or other devices such as a PLC using MODBUS TCP communications. This provides a total system capacity of 360 channels (60 built-in measure channels + 300 external). 

Serial MODBUS RTU communications (RS- 232 or RS-422A/485) can be ordered as a separate option with the same capability.

Connect to Other Devices

Connect to Other Devices

An optional serial MODBUS RTU interface provides data exchange functions with other devices such as recorders, PLCs and controllers. In this mode, MW100 can serve as expansion I/O or as a data acquisition terminal for another connected device.

Remote Data Acquisition

Remote Data AcquisitionWhen the measurement location is located remotely from the data monitoring station, a dial up phone connection can be used for communications. All MW100 web browser-based data monitoring and FTP functions can be used via this connection for remote data acquisition applications. 

Screen updating may be slower depending on the communication environment.

Time Synchronization

Time SynchronizationThe MW100 can synchronize its clock to a network time-server using SNTP (Simple Network Time Protocol), allowing any number of MW100s in a system to have precisely matched time.

Both SNTP Server and Client modes are supported. In Server mode, one MW100 can acquire time data from a server using Client mode. It can then serve time data in Server mode to other MW100s that function as Clients.

Clock synchronization functions are allowed only when the measurement interval within the unit is two seconds or longer.

Memory

Select a CF card appropriate for the required data recording time. See the table below for the approximate time's worth of data that can be recorded for each size of card. For example, when recording ten channels of data at a 10 ms measurement interval, the approximate amount of data that can be recorded to a 128-MB CF card is 8.8 hours worth. On the MW100, measured data is recorded to the CF card via an SRAM. The SRAM is backed up with a battery (for approximately ten years), ensuring that even in the event of a power failure, data prior to the failure is not lost.

Recording channels Measurement interval 128 M 512 M 1 G
10 ch 10 ms1 Approx. 8.8 hours Approx. 1.4 days Approx. 2.8 days
100 ms Approx. 3.7 days Approx. 14.8 days Approx. 28.9 days
500 ms Approx. 18.5 days Approx. 74.0 days Approx. 144 days
1 s Approx. 37.0 days Approx. 148 days Approx. 289 days
2 s Approx. 74.0 days Approx. 296 days Approx. 578 days
(Approx. 1.5 years)
5 s Approx. 185 days Approx. 740 days Approx. 1446 days
(Approx. 3.9 years)
20 ch 50 ms2 Approx. 22.2 hours Approx. 3.7 days Approx. 7.2 days
100 ms Approx. 1.8 days Approx. 7.4 days Approx. 14.4 days
500 ms Approx. 9.2 days Approx. 37.0 days Approx. 72.3 days
1 s Approx. 18.5 days Approx. 74.0 days Approx. 144 days
2 s Approx. 37.0 days Approx. 148 days Approx. 289 days
5 s Approx. 92.5 days Approx. 370 days
(Approx. 1 year)
Approx. 723 days
(Approx. 1.9 years)
60 ch 100 ms Approx. 14.8 hours Approx. 2.4 days Approx. 4.8 days
500 ms Approx. 3.0 days Approx. 12.3 days Approx. 24.1 days
1 s Approx. 6.1 days Approx. 24.6 days Approx. 48.2 days
2 s Approx. 12.3 days Approx. 49.3 days Approx. 96.4 days
5 s Approx. 30.8 days Approx. 123 days Approx. 241 days

Storage capacity in terms of time by CF card size and numbers of channels

  1. At a measurement interval of 10 ms, the maximum number of channels that can be measured is 10. Eleven or more channels cannot be measured at a measurement interval of 10 ms.
  2. At a measurement interval of 50 ms, the maximum number of channels that can be measured is 30. Thirty-one or more channels cannot be measured at a measurement interval of 50 ms.

Multi-Interval

Multi-Interval

The MW100 enables mixing of three different measurement intervals in a single unit. Measurement intervals can be set for each individual module. This allows you to measure various items under test at the most appropriate measurement intervals. Also, you can set data recording conditions1 for each measurement interval, thereby using the available space on the CF card as efficiently as possible.

  1. Single: Save a file up to the specified size then stop recording. Full Stop: Stop recording once the CF card is full. Rotate: When the capacity of the CF card has been exceeded, the oldest files are deleted to free up space, then recording continues.

Trigger and Data Thinning Functions

Data Recording Using the Trigger and Data Thinning Functions

Data Recording Using the Trigger and Data Thinning Functions

The MW100 is equipped with built-in trigger functions. Data recording can be started based on alarm values, time, external contact input, or other parameters. Once recording is started, it can be set to progress continuously or according to a specified data length. When specifying a data length, a pre-trigger can also be set. The MW100 also provides a data thinning function. 

Portions of measured data can be omitted at regular intervals during measurement (minimum of four seconds) before data is recorded. Using the trigger and data thinning functions together provides "coarse" recording of general data and "fine" recording of abnormal data.

Broken Line Chart Output (/M1 Option)

Data Recording Using the Trigger and Data Thinning Functions

This function is included with the MATH (/M1) option. Patterns can be output from the analog output and PWM output modules (MX120) by inputting the coordinates of the pattern you wish to generate. In the pattern output shown in the figure below, points (X1,Y1) through (X10,Y10) are input in advance, and the output is generated accordingly.

Reporting Functions

Creates hourly, daily, weekly, and monthly reports synchronized to measurement start and stop. On mesurement stop action, a report file is saved to the MW100 CF media. A report status display is provided in the web browser monitor mode. Report data is saved to a text (.txt) file compatible with common software applications. 

Up to 60 report channels reporting data from assigned measure or math channels

Report channel data: MIN, MAX, average, summation, and instantaneous values
Report channel data: tabular digital data display and graph for totalizer data
File format: .txt text file (tab delimited)
Report math interval: up to 100 ms
Email messaging: An email message is sent at the report creation time
File transfer: the report file can be transferred to an FTP server at the report creation time

Report logging display

Report logging display

Graph display of totalizer data

Graph display of totalizer data

Use Excel or other applications to create custom reports from the report text file.

Use Excel or other applications to create custom reports from the report text file.

MW100 Automatic Assignment Function (/MC1 Option for the DXAdvanced DX2000)

The DX2000 can use MW100 system hardware as additional external input channels. They can automatically recognize MW100s on a network and perform automatic assignment of the MW100 input channels to build a large multi-point data acquisition system quickly and easily with no PC requirement. System requirements: /MC1 external input option and /M1 math option. See the product bulletins and general specifications for details.

MW100 Automatic Assignment Function

*The firmware version of R2.22 or later is required for the MW100 to support the automatic assignment function.

Firmware R3.04 Functions

  • Support for devices with the Ethernet-Serial Gateway Function
    • The MW100 can now have direct communication with instruments connected via a multidrop connection to the PR300. (client)
  • Added data types
    • INT16 (server/slave)
    • Bit (client/master)
  • Connectivity with upstream devices (CENTUM, etc.)
    • Network load can now be adjusted through frequent polling from upstream devices. (server)

Connection by the Ethernet-Serial Gateway function

Connection by the Ethernet-Serial Gateway function

Firmware R3.03 Functions

Lite Monitor: Enables monitoring with a digital display, even in environments with low transmission speeds.

Setting List: A list of settings that can be displayed in TXT (text) or "printable" format.

Bit output computation: Enables output of the value of specified bits (0/1) of reference channel data (positive integers expressed as bits).

Alarm DO output: Preset settings of Off, Open, and Close were added as operations upon stop or error.

Modbus Slave/Server Function:

  • Added a coil function for mapping data on communication input channels (C001 to C300).
  • Added input relays for measurement channels, computation channels, and the main unit operating status.
  • Added input registers for mapping main unit mode information.

Summer Time Setting: The starting and ending date/time for Summer time can be set.

Firmware R3.03 Functions

Firmware R3.02 Functions

Standard Support for the EtherNet/IP Protocol

Advantages of EtherNet/IP Compatibility

  1. Able to develop a highly flexible systems
    By using Ethernet/IP in the standard interface, the most appropriate multivendor systems can be readily developed for users. In addition, instruments can be added or modified without any additional programming, thus improving efficiency.
  2. Improved trend analysis
    By making it easier to install the MW100 Data Acquisition Unit in systems and thereby facilitating the chronological monitoring of equipment operating conditions and quality data, trends can be analyzed with higher precision.
  3. Transmission of vast amounts of data at high speeds over a wide area
    Data can be regularly transmitted at high speeds to instruments distributed over a wide area.
  4. Easy maintenance over a network
    With Ethernet, maintenance staff do not need to learn a dedicated protocol for each instrument, making it easier to control the network.

Note 1: You must install firmware R3.02 to use EtherNet/IP with the MW100.

Note 2: EtherNet/IP is an open industrial application layer protocol supported by ODVA (Open DeviceNet Vendor Association).

Addition of User Authorization to the SMTP Authorization Function

A user authorization feature has been added to the SMTP Authorization function. SMTP authorization (SMTP Service Extension Authentication: SMTP AUTH) means that verification is made when sending e-mails so that only successfully authorized users can send e-mail. This newly added authorization function serves to further strengthen security for sending of e-mails.

Publikationen

Übersicht:

Fuji uses the MW100 for design and development of battery packs for automobiles (capacitors and secondary cells).

If some bar graphs and numeric values are not correct, try the following. Close all open bar graphs. In Windows Control Panel, open the "Java" control panel. On the Advanced tab of the Java control panel, clear the "Enable the next...
Please update the MW100 firmware to R3.10 or later. To display the MW100 Web monitor screen under Java 8, you must install version R3.10 or later of the firmware on the MW100. When using Java 7, please also refer to the following FAQ. What should I d...
Yes, but only for one module at a time. For example, with a 4-channel high speed module you can set SKIP on 4 channels at once.
This is error "E201." See the user's manual for possible causes and solutions. Press the STOP key to clear the error. If you press the STOP key but the error doesn't clear, press the STOP key again. Up to 3 errors can be held. When ...
Clear the Web browser cache. Note: Note that when the cache is cleared, it may take a few seconds to load pages when you visit them for the first time, but on and after the second time they will be displayed as quickly as before. When you clear the ...
When accessing the CF card from the FTP client software by using the MW100 FTP server function, the update year of the files is shown but not the update time (see figure below). With the MW100, if the update time of the files on the CF card is 6 m...
Java Execution Blocked.
(ns-faq-mw-6022-setting)
When using the Java Runtime announced in Partner Portal in certain network environments, the following message is displayed and the monitoring screen used by Java can become unavailable. This is displayed because Internet Explorer blocks execution...
You can connect six 4-channel high speed universal input modules to the MW100. However, at a scan interval of 10 ms, you can only measure on 10 channels. If you slow the scan interval down to 50 ms, you can measure on 30 channels. Alternatively, cons...
Set the login function. With user rights you can browse data, but you cannot set the measuring range and other values. For instructions, see section 3.2, "Communication settings" in the user's manual. Note: With administrator rights, yo...
Check whether it is FAT16 (FAT) formatting. The MW100 can not read FAT32 formatting. FAT16 supports up to 2 GB, so use a CF card of 2 GB or less.
Yes, by adding the MATH option (/M1). The MATH span setting range is -9999999 to 99999999.
No, only single-byte characters can be used.
When the MW100 is a Modbus client, up to 10 Modbus servers can be connected.
The module might not be recognized. Check the module information in the module information screen of the system setting items. If the module is not recognized, turn OFF the power, check the mounting of the module, then do a system reconfiguration fro...
Measurement might be in progress. If so, stop measurement in the TOP screen.
This is either a setting error related to key or web setting operations, or an error during recording. Check the error descriptions in the user's manual. To clear the error, use the status information screen of the system setting item in the web ...
Waveform data updating can slow down depending on the number of web monitors displayed and network conditions. If you need real time waveform updating, close some of the displays.
The MW100 power cord conforms to the standards below. For the European region, it is VDE, BS, and others. Please check your country's power standards prior to use. D: 3-pin power inlet with UL/CSA cable F: 3-pin power inlet with VDE cable R: 3-pi...
When you change a module and reconfigure the system, the default settings are restored. You will need to re-enter your settings.
ClassFormatError is a Java error. For Windows 7, we recommend using Java Runtime version 6.0. Try uninstalling the latest version of Java and installing version 6.0. Version 6.0 is included on the CD-ROM that came with the product.
No. The FTP client can only send files to a secondary master device upon failure to send to the primary master device.
Release number R3.04 and earlier does not support IE 9. Please update to the latest version using our web download service. Note that the service is not available for models with suffix codes /Z and /Sx (where x is 1–199). In those cases, pleas...
The FTP client is executing. If this 7 segment LED continues operating for a long time, the FTP client settings might be incorrect. Check whether the FTP client settings are correct.
No. When installed, you can use pulse input module integration calculations. However, for any other calculations besides integration, you will need the MATH (/M1) option. Also, you will need the report function (suffix code /M3) if you want to make s...
Ethernet connection between the DX2000 and the MW100
(ns-faq-dxadvanced-1024-connect)
Q: I want to connect the DX2000 and MW100 via Ethernet to acquire data from the MW100 onto the DX2000. Does the MW100 require the MATH function? Also, if I connect a power monitor to the DX2000, this is RS-422 communication, but I want to connect to ...
Can I increase the number of inputs above 48 ch?
(ns-faq-dxadvanced-1015-spec)
You cannot increase the number of input terminals. However, you can load data acquired on other instruments such as the MW100 onto the DX via communications.
Yes. However, the DX1000/DX1000N requires the MATH function option (suffix code: /M1), and the DX2000 requires the expansion channel function option (suffix code: /MC1) or the MATH function option (suffix code: /M1).

Downloads

Bedienungsanleitungen

Möchten Sie weitere Informationen über unsere Mitarbeiter, Technologien und Lösungen?

Kontakt

Top