Exapilot Improves Operations and Reduces Energy Use at PTT Khanom Gas Separation Plant #4

PTT Public Company Limited logo
下載 (784 KB)

Executive Summary

PTT Public Company Limited, Thailand
PTT Public Company Limited, Thailand

In 1997, PTT Public Company Limited built the Khanom gas separation plant (GSP #4). Located in Nakron Srithummarat, 700 km south of Bangkok, GSP #4 receives gas via a 24 inch undersea pipeline from an offshore platform operated by PTT Exploration & Production. The plant produces 246,000 t/y of liquefied propane gas (LPG) and 43,000 t/y of natural gasoline (NGL). The LPG is supplied to homes throughout southern Thailand and to a local power station, which generates electricity for the entire region.

This plant has operated since 1997 with a CENTUM CS production control system (PCS) that was installed by Yokogawa Thailand. It has proven to be highly reliable, operating continuously without any major problems for this entire period.

Khanom gas separation plant (GSP #4)

The Challenges and the Solutions

The customer was seeking to improve safety and have operations run more smoothly not only during plant shutdown/start-up but also during normal operations. Yokogawa Thailand demonstrated that Exapilot was easy to configure and use, and showed how it could be used to fully automate and speed up the start-up and shutdown procedures. This reduced the operator workload around 40% and protected pumps by eliminating unnecessary speed increases that cause them to heat up.

The customer confirmed Exapilot's capabilities in the above application and gradually extended its use to the following applications over a one year period:

1. Oil heater combustion control
Exapilot improves control of a non-linear air damper to optimize the fuel air ratio, based on O2 measurements performed by a Yokogawa zirconium type oxygen analyzer. This reduces the consumption of fuel gas by two oil heaters, and each year saves the company $30,000 in fuel costs and reduces CO2 emissions by 210 tons.

2. Cooling fan control
Previously, eleven cooling fans ran non-stop. Based on ambient temperature readings, Exapilot is able to reduce electricity bills by switching the fans on and off.

3. Feed gas and bypass gas flow control
Exasmoc APC software is normally used to control the feed flow in response to changes in the power plant load. To accelerate response times, feed and bypass gas flow control is now also performed by Exapilot. By switching between these programs, it has been possible to reduce propane costs by $450,000 per year.

4. CO2 composition monitoring
The power plant uses gas from an offshore platform that is approximately 22.5% CO2. If this rises above 25%, plant efficiency goes down. Exapilot maintains CO2 within agreed levels, keeping the power plant customer happy and increasing LPG yield by $450,000 per year.

5. Ship loading
Exapilot controls the venting of the loading pumps and controls product flow during LPG/NGL ship loading, reducing electricity consumption and preventing LPG product loss.

LPG/NGL ship loading

Customer Satisfaction

Kanit Pattarakup, process control and DCS board man at PTT Khanom Gas Separation Plant #4, said, "We are very much happy with Yokogawa's CENTUM CS, Exaquantum, Exasmoc, and Exapilot. Exapilot is really easy to use and has improved production very much, and it has been applied to three main procedures ( start up, shut down, normal operation : 24 sub procedures ) to achieve real production excellence. We have confirmed the high reliability and solid functionality of Exapilot in various applications. This is a real solution package and a good tool for the plan-do-check-act (PDCA) cycle to achieve operational excellence in the plant."

"This year we successfully replaced the existing CENTUM CS with the Yokogawa's most current CENTUM VP. We are always challenging to be a VigilantPlant"

Mr. Pattarakup with CENTUM CS and Exapilot / Mr. Pattarakup with CENTUM VP and Exapilot

產業別

  • 上游

    上游業包含海上和陸上活動,包括井口自動化,分餾,完井和分離,回收和製備地下或水下原油和天然氣。

    當石油被帶到地表時,在運輸之前必須將其分離。在三相分離中,一級和二級分離階段通常分佈有氣體流量,水流量和油流量,氣體的輸送需要管道,並且在輸送之前的上游階段需要進行分餾。液體需要通過罐和管道輸送並處理,這就需要精確的液位測量。

    更多

相關產品&解決方案

  • 程序自動化(Exapilot)

    程序自動化工具(Exapilot)在滿足可靠性、靈活性和生命周期成本方面要求的同時,提供靈活的方法來獲取、優化和維持製程工廠中的流程知識。

    更多
  • 分散式控制系統(DCS)

    我們的分散式控制系統 (DCS) 可自動化和控制製程,提高績效。 已經超過 10,000 家工廠利用Yokogawa DCS 實現生產目標。

    更多

置頂