Measurement of Concentration of Supersaturated NaCl Solution in Salt Dissolvers at Electrolysis Plants

下载 (350 KB)


Control of sodium chloride (NaCl) concentration at a salt dissolver where solid salt is dissolved in water, is highly important because of the electrolysis efficiency. A conventional way of measuring the concentration of supersaturated NaCl solution had been performed by using non-contact type sensors (e.g., γ-ray density meter) since NaCl, impurities, and precipitates are in the solution. In this way, there were disadvantages such as troublesome maintenance and therefore, the radiation control is required for γ-ray density meter. Responding to these backgrounds, the ISC202 inductive conductivity analyzer provides concentration reading and realizes to improve substantial maintainability, cost performance and measurement accuracy.

Caustic Soda Production Process

Caustic Soda Production Process

Expected Benefits

  • Measures NaCl concentration in salt dissolvers
  • Reduces operating costs

Process Overview

In an electrolysis plant, the solid salt is dissolved in water in a salt dissolver to make brine. This brine contains impurities, such as calcium, magnesium or sulfates, that decrease electrolysis efficiency. The brine is purified by removing these impurities before being fed to an electrolyzer, where the purified brine is electrolyzed to produce caustic soda and chlorine. The caustic soda solution produced at the cathode in the electrolyzer is concentrated in a multiple effect evaporator, as a result the concentration is increased from approximately 32% to 48%.

Solution Details

Measurement system

2-wire inductive conductivity system

Sensor ISC40G(J)-GG-T1-☐☐
Flow-through holder ISC40FF(J)-PJ
Transmitter FLXA202-D-BーD-☐-C5-NN-A-N-LA-☐-NN

2-wire inductive conductivity system

Inductive Conductivity Sensor & Transmitter Installation Diagram


ISC202G inductive conductivity transmitter
Power supply voltage: 17 - 40 V DC (from distributor)
Power consumption: 0.9 VA maximum
PH201G distributor
Power supply:
100 V: 20 to130 V DC/80 to 138 V AC, 47 to 63 Hz
220 V: 120 to 340 V DC/138 to 264 V AC, 47 to 63 Hz
Power consumption: 24 V DC: approx. 200 mA
100 V AC: approx. 7 VA
220 V AC: approx. 11 VA


Sampling should be done in the supernatant liquid in a salt dissolver. The supernatant liquid is collected in a settling tank and then the supernatant liquid of the tank is transported to a measurement tank where the sensor is installed.

Field Data

1. Process conditions (salt dissolver)

Temperature: Approx. 65°C
Pressure: Atmospheric pressure
Sample: Supersaturated brine
NaCl concentration control range: 200 to 360 g/L
--> 18.1 to 30 wt%*

* Depends on user's actual data of specific gravity.

2. ISC202G setting parameters

Relationship between conductivity and concentration is based
on the linear approximation of S = 16.3x that is obtained by actual measurement using SC72 Personal Conductivity Meter.

  • NaCl temperature compensation table is used
  • Reference temperature setting: 25°C
  • Output setting: Code 04
Output (%) Concentration (%) Conductivity (mS/cm)
0 18 293
50 24 391
100 30 489


  • 化工


  • 特种和精细化工




  • 2-Wire Transmitter/Analyzer FLXA202

    The FLEXA™ series analyzers are used for continuous on-line measurements in industrial installations. With an option for single or dual sensor measurement, they are the most flexible two-wire analyzer available.

  • pH和ORP分析仪


  • 电导率传感器



Have Questions?

Contact a Yokogawa Expert to learn how we can help you solve your challenges.

WeChat QR Code