Measuring the Electric Conductivity by use of Clean-in-Place (CIP) System

다운로드 (266 KB)

Introduction

In the manufacturing process of Pharmaceutical, Chemical and Food & Beverage industries, the cleaning and sterilization of tanks and piping are done with various cleaning solutions, fresh or hot water and steam after manufacturing products. Clean- In-Place (CIP) is the system designed for automatic cleaning and disinfecting. The recovery of cleaning solutions contributes significantly to reduce chemical costs and wastewater processing costs.

Yokogawa FLXA21 inductive conductivity transmitter has earned a reputation in the recovery of cleaning solutions because it can take measurements with good boundary surface precision over a wide range.

CIP Process Flow

CIP Process Flow

Expected Benefits

  • Optimizes cleaning and sterilizing application for tanks and piping by use of CIP
  • Reduces operating costs

Process Overview

Inductive Conductivity SensorCIP systems depend on the process differentiations of Pharmaceutical, Chemical and Food & Beverage. In addition, the cleaning solutions and chemicals are different. The chemicals that are generally used are hypochlorous acid, caustic soda, and nitrous acid. In a cleaning solution recovery system, the process lines and piping are cleaned with an initial cleaning solution. After that, the cleaning solution is cleaned with fresh water. The cleaning solution is recovered at that point, but since it gradually becomes diluted with fresh water, recovery is discontinued and the solution is discharged through a drainage line when the concentration of the cleaning solution drops below the standard value. The cleaning with different solutions or fresh water, the recovery of the cleaning solution, and the discharge of waste solution are repeatedly carried out. In addition, sterilization with steam or cleaning with distilled water or de-ionized water is performed as a final step in some cases.

Solution Details

Measurement system
2-wire inductive conductivity system
Sensor ISC40G(J)
Flow-through type holder ISC40FF(J)
Transmitter ISC202G-A-E
Dedicated distributor for transmitter PH201G-A☐*B

Utilities

ISC202G inductive conductivity transmitter
Power supply voltage: 17 - 40 V DC (from distributor)
Power consumption: 0.9 VA maximum
PH201G distributor
Power supply: 100 V: 20 to130 V DC/80 to 138 V AC, 47 to 63 Hz
220 V: 120 to 340 V DC/138 to 264 V AC, 47 to 63 Hz
Power consumption: 24 V DC: approx. 200 mA
100 V AC: approx. 7 VA
220 V AC: approx. 11 VA

Notes

Temperature range of transmitter is -20 to 140°C

Field Data

1. Process Conditions

  Concentration (%) Temperature (°C) Pressure MPa
Water - 4 to 20 0 to 1
NaOH solution 1 to 5 80 to 90 0 to 1
HNO3 solution 1 to 5 80 to 90 0 to 1
Steam - below 130 0 to 1

2. Features of ISC Inductive Conductivity Meter used in a CIP Process

zero-suppression function
Zero-suppression function
  1. Improved precision in boundary surface measurement.
    (a) Equipped with a zero-suppression function according to output signal
    * Zero suppression
    Example:
    Output: 4 to 20 mA DC
    Range: 100 to 300 mS/cm
    (b) One sensor can handle a minimum span of 100µS/cm and a maximum span of 1999 mS/cm.
  2. Steam sterilization capability
    Measurements can be performed at process solution temperatures of -10 to 130°C and pressures no greater than 2 MPa {20 kgf/cm2}

업종

Related Products & Solutions

2-Wire Transmitter/Analyzer FLXA202/21

FLEXA ™ 시리즈 분석기는 산업용 설비의 연속 온라인 측정에 사용됩니다. 단일 또는 이중 센서 측정 옵션이 있어 가장 유연한 2 선식 분석기입니다.

Inductive (Torodial, Electrodeless) Conductivity Analyzer

유도식 전도도 방법은 특히 높은 전도도 측정에 적합합니다. 분석계는 2개의 Troidal 변압기가 내장된 센서와 함께 작동합니다. AC 전류는 공정 샘플에 전압을 유도하여 샘플에 전류를 발생 시킵니다. 이 전류의 세기는 옴의 범칙에 따른 샘플의 전도도에 비례합니다. 

Inductive (Torodial, Electrodeless) Conductivity Sensor ISC40

ISC40 센서는 EXA ISC 분석계와 함께 사용하도록 설계되어 있습니다. 이 조합은 신뢰성, 정확성, 범위성, 가격 성능 측면에서 전도도 측정에 대한 모든 기대를 초과합니다.

Conductivity Sensors

전도도 센서와 전극은 공정 전도도, 저항률, WIFI, 탈염 수, RO 수, 농도 퍼센트, 보일러 블로우 다운 및 TDS를 측정하는 데 사용됩니다. Retractable, Flow-though, 침적 및 직접 삽입을 포함한 다양한 설치 옵션이 있습니다.

적절한 전극 / 센서 선택은 최적의 측정 결과를 위해 중요합니다.

pH and ORP Analyzers

pH와 ORP 미터, 분석계 및 전송기는 수질/제품 품질을 보장하고 유출물 배출량, 배치 중화, 펄프 스톡, 세정기, 냉각 타워, 화학, 폐수 처리 및 기타 여러 어플리케이션의 연속 공정 모니터링에 사용합니다.

×

Have Questions?

Contact a Yokogawa Expert to learn how we can help you solve your challenges.

Top