Establishing an Environmental Load Management System for Factories

다운로드 (1.2 MB)

Takane Misawa1 Masao Yanagimori2 Satoru Isobe3

Mercian Corporation has established an environmental load management system at its Yatsushiro Factory by using Yokogawa's Enerize factory energy management system. The system is intended to manage data not only on energy consumption but also on the environment relating to production activities such as the amount of water consumed in the factory. This paper describes the successful introduction of this system.

  1. Registered Energy Manager, Production Dept. Production Headquarter, Mercian Corporation
  2. Registered Energy Manager, Facilities Institution Section Yatsushiro Plant, Mercian Corporation
  3. Green Factory Solutions Business Center, Industrial Automation Business Headquarters


As a company that has strong relationship with nature and provides products using nature's blessings, Mercian Corporation is committed to the environment. Its environmental philosophy is "Mercian thanks nature's blessings and capability that sustain life, and seeks to balance environmental preservation with creating an affluent society." To create a sustainable society, the company strives to conserve resources and energy, develop environment-friendly products, disclose information regarding environmental impact, and comply with laws. This paper describes the environmental load management system which was established at Yatsushiro Factory, one of Mercian's largest production bases, with Yokogawa's Enerize factory energy management system for factories.


Mercian recognizes that business activities inevitably impact on the environmental load. To fulfill its responsibility for maintaining the environment and creating a sustainable society, the company has set the following mid-term targets, based on its philosophy and management policy on the environment1.

Target 1: Reducing CO2 emissions caused by energy consumption
Factories: Reducing emissions by 7% in FY2012 compared with FY2002
Logistics: Reducing emissions below those in FY2004

Target 2: Reducing the use of water for manufacturing
Reducing usage by 20% in FY2012 compared with FY2002

Target 3: Reducing waste
Reducing the amount below that in FY2004

Target 4: Reducing the emissions of substances designated in the pollutant release and transfer register (PRTR) system
Reducing the emissions to 1/5 of those in FY2002 in FY2012

Target 5: Reducing the environmental load caused by containers and wrappings for liquors
Reducing their weight per capacity below those in FY2002

When building the environmental load management system, we concentrated on the management and reduction of CO2 emissions (target 1) and water for manufacturing (target 2) among these targets.

Table 1 shows the CO2 emissions and use of water for manufacturing by each production base in FY20081. The CO2 emissions due to energy consumption and use of water across the company increased by 3.6% and 6.5%, respectively, compared with FY2002. As shown in the table, Yatsushiro Factor y, which is the target of the management system, produces various items and thus emits more CO2 and uses more water than other factories. Therefore, we put priority on these reductions in the factory than in other factories.

Table 1 CO2 emissions and use of water for manufacturing by each production base

Production base Main products CO2 emission [t] Use of water for manufacturing [kt]
Tomakomai factory Cattle feed 4,766 15
Nikko factory Rice wine, seasonings, drug products, others 4,665 487
Fujisawa factory Wine, others 6,579 237
Katsunuma winery Wine 347 77
Iwata factory Medicine and chemicals 6,394 1227
Uwajima factory Fishery feed 1,087 10
Yatsushiro Factory Shochu (Japanese distilled clear liquor), medicine, chemicals, others 92,292 6,789


Figure 1 Previous Flow of Operations from Collecting to Announcing Environmental Data

Issues in Yatsushiro Factory

  1. Increased tasks regarding environmental management
    Including compliance with the Revised Energy Saving Act enforced in 2010, tasks related to environmental management are tending to increase at the company level as well as in each factory. Figure 1 shows the previous flow of operations in respective factories from collecting environmental data to announcing them. The review and implementation of measures for energy conservation and environment preservation were not included.
    As shown in Figure 1, the previous workflow started with collecting data from the reports created by the control systems for utility facilities such as electric power, steam, and air-conditioning, and the measured data by visual reading of the field instruments at the end of every month. These data were then transferred manually into Excel worksheets for calculation and reporting. When any equipment or management organization was changed, the content of worksheets had to be adjusted accordingly and the calculation performed again. Reports were then created showing the energy cost for each organization and aggregation or allocation of energy and water to and from each organization and production line. It took about 20 man-days a month to perform this work, which reduced the time available for other activities including actually taking energy-saving measures. As a result, the management operations, which should have been carried out according to the PDCA cycle, were done only for collecting and reporting data.
  2. Information ownership
    Yatsushiro Factory is an old production base which started up in the 1940s, so it has repeatedly reorganized and upgraded its production facilities. The worksheets for calculation and reporting used in the work described above have been revised by successive Registered Energy Managers to reflect such reorganization. However, we could not find detailed records on the reasons for revisions; in the past, only the people in charge possessed such information.

Targets in Solving the Problems

To solve the problems and improve the efficiency, we set the following targets for the new system.

  • Reducing workloads 
  • Creating a calculation tool well suited to the present configuration and a system that can easily handle the reorganization and innovation of factory facilities in the future
  • Clearly showing the energy consumed per unit production by each product and production line to establish the PDCA cycle

To solve the problems on the site and encourage the PDCA cycle to be carried out, it is necessary to identify inefficient areas of the factory. To do this, it is necessary to visualize the site timely, define key performance indicators (KPI) which shows the status of products and production lines and can be used for decision making, and manage them based on the indicators. As the Indicators (KPI), we have adopted the energy consumption per each product by production line and facility. We decided to measure the indicators, set new targets of the indicators utilizing the measured values, and build an environment to support the daily PDCA cycle.


To achieve the goals, we built an environmental load management system at the Yatsushiro Factory based on Yokogawa's Enerize factory energy management system.

Procedures to Build the System

Figure 2 outlines the flow to build the system.

Figure 2 Outline of the flow to build the system

The detailed procedures to build the system are as follows.

  1. Figure-3-Energy-flow 
    Figure 3 Energy flow
    Creating a list of measurement points
    A list of measurement points was created as follows.
    • Determining appropriate measurement items by examining existing system specifications such as electric power system diagrams and steam piping diagrams, existing Excel worksheets for managing and calculating the data, information on existing management reports, and the production sites
    • Checking the appropriateness of extracted measurement items by referring to the information that must be included in the report or management
    • Defining properties for each measurement item, including types of energy, location information (building, floor, line, process, and equipment), and usage, then arranging them as a list of measurement points
  2. Creating the energy flow
    Based on the electric power system diagrams, steam piping diagrams, and existing Excel worksheets for managing and calculating the data, the energy flow was created by using Visual Builder of Enerize, and the relations between respective measurement points and equipment were defined and arranged.
    Figure 3 shows the energy flow created by this work. This allows everyone to easily know the energy balance of the factory. This energy flow includes about 500 measurement points and about 2,000 steps related to converting to energy equivalent, CO2 equivalent, and cost equivalent in 14 sheets.
  3. Figure-4-Definition-of-organization-allocation-data
    Figure 4 Definition of organization, allocation data, and allocation ratio
    Arranging and defining allocating information for each department
    The rules for allocating energy consumption to each department were defined based on information on the existing worksheets for calculating and managing the data. As shown in Figure 4, this information was defined in terms of organization, data to be allocated, and allocation ratio by using Visual Builder of Enerize.
  4. From definition of user tasks to definition of Human Machine Interface (HMI)
    The most important requirement when building the system is its operational requirements. However excellent the system is, its usefulness depends on how it is used. Since Enerize can define the configuration of screens depending on the flow of user operations and counter measures for difficulties, we could define the development menu of HMI while arranging the flow and purpose of the user tasks.

Total System Configuration

Figure 5 shows the system configuration and other systems.


Figure 5 Total System Configuration

Yokogawa's CENTUM CS3000 and TriFellow are used for the boiler control system and power relating facilities monitoring system. PLCs are used to control and monitor the electricity relating facilities and production facilities in the factory. These systems, PLCs and Enerize are connected through the OLE for process control (OPC) interface, and Enerize collects data periodically.

Data is sent to client PCs via a Web server. To ensure security, it is preferable to build an independent LAN between client PCs and the Web server, as well as between the Web server and data collecting systems such as Enerize. However, constructing a LAN over a wide area would require major work, so we compromised to use the existing in-house LAN and built a virtual local area network (VLAN) by installing routers for restricting unauthorized access to areas that need strict security. To do this, we worked closely with Mercian's in-house information service department.

Mercian's original per unit production management system and Enerize are connected through the file interface. The system accumulates and manages the information for energy per unit production generated by Enerize based on information such as manufacturing items, production lines, production quantities, and start and completion times of each manufacturing lot.

Overview of System Functions


Figure 6 System Functions and Flow of the Data

Figure 6 shows the functions of the environmental load management system and the flow of the data. The main functions are summarized below.

  • Collecting data:
    Data is collected with the time stamp every minute through the OPC interface.
  • Calculating following energy models:
    Total energy costs, costs in supplying one energy unit, and CO2 emission at each measurement point are calculated following the energy flow defined by Visual Builder by using calorific values converted from measured raw data. Coefficients of performance (COP), calorific energy loss, and cost loss of each energy conversion equipment are also calculated.
  • Closing:
    Maximum, minimum, average, and total values, and the number of counting are calculated for the measured or calculated data. The hourly, daily, monthly, and yearly closing calculations are performed.
  • Allocation:
    Specified data is allocated based on an allocation table, which is defined by using the occupying area and rated values of each equipment.
  • Summing up for each category:
  • Total values for each category are summed up based on the defined tree structure (hierarchy of organizations and processes).
  • Designing and displaying graphs:
    Various graphs are designed and assigned to be displayed simultaneously with the management criteria. These graphs can be displayed respectively by calling up their name.
  • Designing and displaying images by HTTP:
    Screen images are designed using the Hyper Text Transfer Protocol (HTTP) format to show the screens registered for Web browsing on any PCs connected to the in-house LAN. Internet Explorer is used to display them.


The results and expected effects of these activities are as follows.

  1. Improving the efficiency of management operations
    Workloads for compliance with regulations such as the Revised Energy Saving Act tend to increase. As mentioned in the "Issues in Yatsushiro Factory" section, many man-hours were needed merely to create reports. The new system reduced the time required for management work to just 20%. This is because each operation such as collecting data and converting raw measurements to CO2 emissions, costs, and energy consumption is now carried out automatically. The man-hours thus made available can be used for preventive maintenance and improvement activities to improve productivity.
  2. All members are Registered Energy Managers.
    Previously, only Registered Energy Managers were engaged in environmental preservation and energy conservation activities. This new system can presents clear indicators for energy and water (per unit production), and thus helps all members involved in production to be aware of energy consumption.
  3. Preventing ownership by limited people
    Through building this system, we organized measuring items and energy flow related to the target equipment and clearly wrote down them as the correct information reflecting the actual status of the factories. The information previously belonged to limited people was made public, and that increased the degree of information sharing and created an environment where all members can utilize it. Especially, worksheets for data calculation were changed so easy by the energy flow as every one, not just the author, can understand.


Companies must comply with increasing management requirements such as the Revised Energy Saving Act, ISO14000, and ISO50001. Moreover, they need to respond to the carbon footprint system that requires marking for CO2 emissions. Thus, the circumstance of companies' environment- oriented management is becoming more severe. We expect this approach in Yatsushiro Factory can be deployed to other Mercian's manufacturing bases, thus promoting beneficial environmental management throughout the company.


  1. Mercian Corporation, "CSR report 2008/2009,"
  • CENTUM, Enerize, TriFellow, and Exaopc are registered trademarks of Yokogawa Electric Corporation.
  • Excel and Internet Explorer are registered trademarks of Microsoft Corporation.


  • 바이오매스 발전

    바이오매스는 최근 화력 발전소가 이산화탄소 배출량을 줄일 수 있는 재생 가능 에너지원이기 때문에 점점 더 이슈가 되고 있습니다. Yokogawa 시스템은 바이오매스를 사용하는 발전소를 포함하여 모든 유형의 발전소에서 전 세계적으로 사용되고 있습니다. Yokogawa의 측정 및 제어 기술을 통해 발전소는 보다 효율적으로 운전이 가능하며 탄소배출을 줄일 수 있습니다.

    See More
  • 벌크화학

    석유 화학 제품, 무기물 또는 중간체를 생산하든 관계없이 화학 회사는 안전하고 호환되는 작업을 유지하면서 적시에 효율적인 방법으로 제품을 제공하는 비용과 마진 압박에 시달리고 있습니다. 또한 화학 회사들은 공급 원료 및 에너지 가격의 변동에 적응하고 가장 수익성 높은 제품 혼합을 시장에 제공해야 합니다.

    Yokogawa는 벌크 화학 시장의 자동화 요구 사항을 세계적으로 지원해 왔으며 이 시장에서 인정받는 선두 주자입니다. Yokogawa는 제품, 솔루션 및 업계 전문 기술을 통해 시장 및 생산 요구 사항을 이해하고 플랜트의 수명주기를 통해 안정적이고 비용 효율적인 솔루션을 제공하기 위해 협력합니다.

    See More
  • 전력

    1970년대 중반, Yokogawa는 EBS 전기 제어 시스템 (EBS Electric Control System)의 출시와 함께 전력 사업에 진출했습니다. 그 이후로 Yokogawa는 전 세계 고객에게 최상의 서비스와 솔루션을 제공하기 위한 기술과 역량의 개발을 꾸준히 지속해 왔습니다.

    Yokogawa는 역동적인 글로벌 전력 시장에서 더욱 적극적인 역할을 수행하기 위해 글로벌 전력 솔루션 네트워크를 운영했습니다. 이로 인해 Yokogawa 내에서 보다 긴밀한 팀워크가 가능해져서 글로벌 리소스와 업계 노하우를 하나로 모았습니다. Yokogawa의 전력 산업 전문가들은 각 고객에게 정교한 요구 사항에 가장 적합한 솔루션을 제공하기 위해 협력합니다.

    See More
  • 정수 및 하수 처리

    Yokogawa는 보다 효율적인 사회를 만들기 위하여 에너지 최적화 기술 개발, 온실가스 감축, 오염 물질로부터 환경을 보호하는 견고한 제품 제작 등을 통해 지속 가능한 수자원 생산을 위한 제어 솔루션을 제공하고 있습니다. Yokogawa의 첨단 기술과 폭넓은 애플리케이션 노하우를 통해 고객과 협력하여 사업을 활성화하고 플랜트 수명주기 전반에 걸쳐 높은 가치를 제공할 수 있는 지속 가능한 솔루션을 제공합니다. 당사의 기술과 제품은 플랜트의 성능을 향상시키고 오늘날의 수자원 시장에서 경쟁적으로 운영할 수 있도록 보장하며 운영비를 절감합니다. Yokogawa는 지자체 및 공업용수 처리 시장에서 광범위한 수처리 응용 분야를 지원합니다.

    See More
  • 지열발전

    지열에너지는 기상 조건에 의존하지 않기 때문에 일 년 내내 안정적인 전력을 공급할 수 있습니다. 또한 어떤 연료도 지상에서 태우지 않으며 매우 적은 양의 이산화탄소만 배출되므로 환경친화적입니다. 태평양, 일본, 필리핀, 인도네시아, 뉴질랜드, 멕시코, 코스타리카, 미국 등의 국가에서 태평양 연안 벨트 ("불의 고리"라고도 함)를 따라 풍부한 지열 자원이 있습니다. 다른 지열 활동 지역에 위치한 아이슬란드, 터키 및 이탈리아와 같은 국가들과 협력합니다. Yokogawa는 현재까지 일본, 동남아시아 및 기타 지역의 30개 지열발전 프로젝트를 실행한 경험을 바탕으로 지열발전 시스템의 신뢰성 및 유지 관리 효율성을 향상시키는 다양한 측정 및 제어 기술을 제공하고 있습니다.

    See More

Related Products & Solutions

  • 분산 제어 시스템 (DCS)

    Yokogawa는 프로세스 자동화를 위해서 중요한 운영 인프라를 제공합니다. 분산제어시스템(DCS)은 플랜트 또는 산업 공정의 자동화 된 제어 및 운영을 위한 플랫폼입니다. 10,000개 이상의 플랜트에서 고객의 생산 목표 달성하기 위해서 Yokogawa DCS가 적용되었습니다.

    See More