CIP Process Lines

다운로드 (281 KB)


Ceramic lined magmeters have seen increased use in biotechnology industries in recent years. The characteristics of the liner make it highly desirable in sanitary applications. Ceramic liners can tolerate higher temperatures and pressures than most other liner materials. Other liners can also release plasticizers and drying agents into the product in a process referred to as leaching. Ceramic liners are much less likely to contaminate the process by leaching. One particular concern when using ceramic liners is thermal shock and the damage that can be done when inferior designs are subjected to large, rapid swings in temperature.

Typical Biotechnology Installation

Typical Biotechnology Installation 


Yeast is used in industrial processes such as the production of antibiotics, penicillin and other medicines, and in the fermentation of beer and alcoholic beverages. If the lines are not sterile, a yeast fungus can infect the process, and ruin the batch. Cleaning and sterilization between batches is an absolute necessity, and is often accomplished through the use of hot water or steam. CIP (Clean In Place) and SIP (Sterilize In Place) applications can subject meters to drastic temperature fluctuations in short periods of time. These temperature swings can lead to a variety of failures in meters with inferior design and materials of construction. Electrode seals can fail due to differing expansion rates of the liner and electrodes, and inferior liner materials can crack and fail, causing leakage or loss of the measurement.


Yokogawa's ceramic liner can offer the customer superior resistance to thermal shock and the failure that can occur due to liner cracking. This is due to Yokogawa's use of 99.9% pure Al2O3 for the liner. While the difference between our use of 99.9% pure Al2O3 and the competition's use of 99.7% may seem insignificant, the effect on thermal shock capability can be considerable.

Specification for Thermal Shock
Typical Ceramic Liner
Increase 150°C (302°F) per 10 minutes
Decrease 80°C (176°F) per 10 minutes

Ceramic ADMAG*
Increase 100°C (212°F) per second
Decrease 50°C (122°F) per second

*Refer to Manufacturer's GS Sheets for details.

Differences in Solid and Cermet Electrode Construction
Differences in Solid and Cermet Electrode Construction

Another major advantage of the ADMAG ceramic design is the electrode construction. All sizes of the ceramic lined ADMAG utilize a Platinum-alumina cermet electrode. The electrode is a mixture of Platinum/alumina powder which is sintered into the liner during the manufacturing process.

The result is an electrode which is an integral part of the liner. This method of construction has several major advantages over solid electrode designs. The primary benefit is the elimination of two potential leak paths. Since the electrodes are an integral part of the liner, there is no seal to fail as with competitors' meters using solid electrodes.

Another advantage that cermet electrodes have over solid electrodes is that the cermet Electrode and the Al2O3 liner have the same thermal expansion rates. With a solid electrode, the liner and electrode have different thermal expansion rates. Differing expansion rates can lead to improper sealing around the electrode and, over time, can contribute to stress cracks at the electrode/liner seal. Both can lead to premature failure of the meter due to leakage.

A major biotechnology manufacturer recently conducted a year long test to evaluate the effects of thermal shock from CIP cleaning on mag meters with ceramic liners. The ADMAG completed the test with no problems, while meters from other manufacturers showed blistering and cracking. Some manufacturers even elected not to finish the test and withdrew their meters before the test was completed!


Yokogawa's use of cermet electrodes and 99.9% pure Al2Oallows the ceramic ADMAG to provide reliable service where our competitor's meters will most likely fail due to leakage around the electrode, or thermal cracking of the liner. This can offer your customer longer service life with less down time, lower maintenance cost, and lower overall operating cost.

ADMAG AXF Ceramic lined

  • 99.9% pure Al2O3 liner
  • Sintered platinum-alumina cermet electrode in all sizes
  • Elimination of two potential leak paths
  • Higher pressure and temperature limits than other liner materials
    · Up to 180°C at 4MPa (356°F at 580 psig)
  • Superior thermal shock resistance
    · Up to 100°C (212°F)/second
  • Accuracy 0.35%, 0.2% as option



  • 식음료

    식품 제조 산업에서는 "식품 안전 및 안전 보장"과 "비용 절감"을 모두 달성해야 하는 전통적인 과제 외에도, 제조업체들은 감염병 대응과 노동력 절감에 대처하기 위해서도 노력하고 있습니다.
    Yokogawa는 긴밀히 협력하고, 함께 도전에 대처하며, 운영에 적합한 이상적인 공장을   제안함으로써  제조업체들이 편안한 작업 공간을 만들 수 있도록 지원합니다.

    See More

Related Products & Solutions

  • 전자 유량계

    Yokogawa의 전자 유량계에 대해 수십 년의 경험을 가지고 있습니다. 당사의 전자 유량계는 대부분의 산업 분야에서 유연한 구성을 제공합니다.

    See More