Sour Water Stripper Process

다운로드 (201 KB)

Background Information

Sour Water is the wastewater that is produced from atmospheric and vacuum crude columns at refineries. Hydrogen sulfide and ammonia are typical components in sour water that need to be removed before the water can be reused elsewhere in the plant. Removal of these components is done by sending the sour water from the process to a stripping tower where heat, in the form of steam, is applied. The ammonia and hydrogen sulfide contained in the water is released by the heat and exits the top of the tower.


The ideal pH value for stripping H2S is below 5, since above 5, sulfide is primarily found in the form of ions (HS- or S-2). Alternatively, efficient ammonia stripping requires a pH above 10 to prevent the formation of ammonium (NH4+) ion that cannot be stripped. Although the most favorable strategy for sour water stripping is a three step process where two separate stripper towers are used, one for removing hydrogen sulfide and the other for removing ammonia, economics usually dictates a compromise. Having only one stripper tower and using a pH around 8 allows adequate removal of both gases.

There are three distinct processing steps in the sour water stripping process: degasification, hydrogen (acid-gas) stripping and ammonia stripping. Figure 1 shows only one stripper column.

During the degasification stage the sour water feed from the plant is cooled and fed to a degasser where dissolved hydrogen, methane and other light hydrocarbons are removed. These removed gases are known as sour Gas and are pumped off to the Sulfur Recovery Unit (SRU). This degassed sour water is pumped into a storage tank that serves to dampen the flow rate and facilitates removal of entrained oil and solids.

The next step in the process is known as hydrogen sulfide stripping. The degassed sour water is fed to the acid gas or hydrogen sulfide stripper, which is a steam-reboiled distillation column. The hydrogen sulfide, which is stripped overhead, is of high purity – an excellent feed for sulfur recovery units or sulfuric acid plants.

Next, the hydrogen sulfide stripper stream, containing all the ammonia in the feed water and some hydrogen sulfide, is fed directly to the ammonia stripper, which is a refluxed distillation column. In this column, essentially all ammonia and hydrogen sulfide are removed from the water. After exchanging heat with the hydrogen sulfide stripper feed, the stripped water is cooled and sent off for either reuse or treating.


Measuring pH in sour water poses several challenges. The abrasiveness of the wastewater affects the pH electrodes over time; the reference electrode junction may plug and require cleaning; and the reference element itself will be poisoned over time due to the presence of hydrogen sulfide. Process temperatures, which affect sensor life, can be quite high in order to facilitate removal of the unwanted components. Ammonia and cyanide can poison the reference electrode by reacting with the silver element.

Product Recommendations

There are two recommended pH sensor combinations we recommend for sour water monitoring. If you are looking for a retractable installation assembly, the PH87 holder with the PH97/DP sensor is the best chose. The sensor's solid state reference provides longer lifetime by lengthening the amount of time it takes for the reference to become poisoned.

For either a flow thru or a direct insertion assembly we recommend breaking the pH measuring system up into it three parts: the measuring electrode, reference electrode, and the temperature electrode. The Yokogawa FF20 is the flow thru holder and the FS20 is the direction insertion holder, each are available in different materials of construction. For the temperature electrode we recommend the SM60-T1, a Pt1000 thermometer. The measuring electrode we recommend is the SM21-AL6, a heavy duty glass electrode that is strengthened for chemical resistance and higher temperatures. The Bellowmatic SR20-AC32 reference electrode is recommended for the reference electrode because of its flowing junction and ability to automatically compensates for process pressure variations.

When either pH assembly is matched with any Yokogawa pH analyzer, the user is provided with diagnostics that warn for sensor breakage or coating. Yokogawa analyzers reduce the guesswork as to when maintenance is required in the pH measuring loop. Compatible pH analyzers are either the Model PH202 for Class I Div I areas, or the model FLXA402 for Class I Div II areas. For Complete details on each piece of equipment please refer to the appropriate product specification pages.

Figure 1 Sour Water Stripper Process Flow Diagram

Figure 1 Sour Water Stripper Process Flow Diagram

Related Products & Solutions

  • 2-Wire Transmitter/Analyzer FLXA202

    The FLEXA™ series analyzers are used for continuous on-line measurements in industrial installations. With an option for single or dual sensor measurement, they are the most flexible two-wire analyzer available.

    See More
  • Digital SMART SENCOM™ Adapter, SA11

    Reusable SMART adapter, requiring only the analog sensor to be disposed of when it reaches the end of its lifetime. With the SENCOM 4.0 platform, Yokogawa delivers reduced costs and waste while contributing to its long-term business goals of a sustainable future for all.

    See More
  • Flow/NPT Fittings FF20/FS20

    Yokogawa는 설치 및 유지보수 시간을 줄이고 결과적으로 운영 비용을 절감하는 설계에 특히 중점을 두어 전체 범위의 피팅을 생산하는데 상당한 설계 및 개발 시간을 투자했습니다.

    See More
  • Industrial pH/ORP Electrodes

    pH 측정 루프의 핵심은 전극 시스템입니다. Yokogawa는 이 핵심이 가장 가혹한 조건에서도 발휘될 수 있도록 광범위한 전극을 설계했습니다.

    See More
  • pH and ORP Analyzers

    pH와 ORP 미터, 분석계 및 전송기는 수질/제품 품질을 보장하고 유출물 배출량, 배치 중화, 펄프 스톡, 세정기, 냉각 타워, 화학, 폐수 처리 및 기타 여러 어플리케이션의 연속 공정 모니터링에 사용합니다.

    See More
  • pH and ORP Sensors

    pH 전극 및 센서는 pH 측정의 감지 부분입니다. Retractable, flow-though, 침적 및 직접 삽입을 포함한 다양한 설치 옵션이 있습니다.

    적절한 pH 전극 / 센서 선택은 최적의 측정 결과를 위해 중요합니다.

    See More