YFGW520 현장 무선 수신기는 국제 자동화 협회 (ISA)의 산업 자동화를 위한 무선 통신 표준 인 ISA100.11a를 기반으로 합니다. 이 제품은 ISA를 기반으로 한 백본 라우터 기능이 있으며 현장 무선 관리 스테이션 (YFGW410) 및 / 또는 현장 무선 미디어 컨버터 (YFGW610)와 결합하여 현장 무선 시스템을 구성합니다. YFGW520은 YFGW510의 후속 제품으로 보다 강력하고 장거리 백본 네트워크를 구축 합니다.
- 세계에서 가장 작은 클래스의 고성능 산업용 무선 중계 장치 :
이 제품은 여러 무선 표준을 기반으로 하는 세계 최소형의 산업용 무선 중계 장치입니다. 이 제품은 현장 무선 네트워크를 확장하고 안정적인 통신을 제공합니다.
- Duocast (ISA100.11a 표준) :
이 제품에는 ISA100.11a 표준의 Duocast 기능이 있습니다. 두 대의 YFGW520을 동시에 사용하여 현장 무선 통신의 신뢰성을 높일 수 있습니다.
- 견고한 플랜트 네트워크 :
YFGW520은 광 통신 옵션의 두 가지 유형을 지원하여 YFGW610과 결합하여 노이즈에 강한 장거리(최대 5km) 백본 네트워크를 구축 할 수 있습니다.
|Raw data rate||250kbps|
|RF Transmitter Power||Max 12dBm|
|Communication Protocol||Field Wireless||ISA100.11a|
|Management configuration, etc.||－|
|Raw data rate||1～54Mbps||100Mbps||100Mbps|
|RF Transmitter Power||Max 15dBm||－||－|
|Connector||N type||RJ-45||SC connector
[ single pole × 2 ]3
|Cable Type||coaxial||Category 5||Multimode fiber*6 Single mode fiber*6|
|Port||Max 2 port||1 port||1 port|
|Communication Protocol||Field Wireless||－||－||－|
|Management configuration, etc.||IEEE1588PTP v24,
- In outdoor wiring to Field Network or 100BASE-TX of Field Wireless Backbone, use optical fiber cables with a nonmetallic tension member, combining with YFGW610
- This product requires a wireless LAN access point for connection with YFGW410 in the wireless LAN in field wireless backbone.
- 2-pole SC connector cannot be used due to the conduit hole size limitation. SC connector should use Short Boot type.
- Installation of these multiple product and YFGW410 in one field wireless subnet requires direct connection or the connection via IEEE1588PTP basis products.
- TCP based custom protocol used for communication between this product and YFGW410.
- YFGW510 supports only Multimode fiber, and YFGW520 supports two types of optical fiber communication option.
|Functional specifications||Temperature Range||Operating: -40 to +65°C (altitude: up to 3000m)
Storage: -40 to +85°C
|Humidity Range||Operating: 5 to 95 %RH (non-condensation)
Storage: 5 to 95 %RH (non-condensation)
|Temperature gradient||Operating: ±10°C/h or less
Storage: ±20°C/h or less
|Power Supply||Voltage Range: 10.0～26.4 V DC
Rated Voltage: 24 V DC
Momentary Power Failure: Instant Disconnection
DC Power Supply Ripple Ratio: 1%p-p or less
|Power Consumption||Max. 3.5 W|
|Grounding||Class-D grounding (no sharing ground with others)|
|Cooling||Natural Air Cooling|
|Regulatory Compliance Statements||Regulation Conformity of the Wireless Module||
|R&TTE Conformity Standards||
|Safety Requirements||CSA C22.2 No. 61010-1|
|Explosion Protected Types||FM, CSA Nonincendive Approval
ATEX Type n declaration
IECEx Type n Approval
ATEX, IECEx Flameproof Approval
FM(United States or Canada): Flameproof Approval (under pending)
One important risk to manage with regard to coal stacks is preventing fires due to spontaneous combustion.
Wireless Multi-Input Temperature Transmitter YTMX580 can accept inputs from up to 8 points, and contribute to your CAPEX cost reduction.
Delayed Coker is a type of coker who's process consists of heating residual oil feed to its thermal cracking temperature in a furnace. The most important variable in industrial furnace control is temperature. Temperature is measured throughout the furnace in different zones and temperature effects the materials being manufactured and therefore must be precisely monitored to prevent deviations in quality of the final product.
Eliminating the wire using wireless transmitter is the perfect solution for rotating equipment. It establishes data collection between the transmitter and the gateway by reliable communication even though the dryer was rotating.
Blending plays a key role in industries such as food, healthcare and chemicals etc. Temperature and vacuum measurements are very important in minimizing the moisture content to ensure the quality of the final product. Strictly maintaining them throughout the process ensures the final product yield.
Direct Reduction Iron (DRI) is one of the processes to reduce oxygen from iron oxide pellets for steel plant. More than 90% of DRI processes use heated LNG as process gas where PID control for temperature or interlock control is of vital importance.
Pressure measurement of tubeless tyres to monitor the air loss is one of the key performance tests in the tyre manufacturing units. Relocation of tyres from one testing rack to the other for various tests and frequent movement of the testing setup for conditional tests to various locations calls for cable free implementation for ease of handling.
Wireless technology has a long history, and it began around the time that James C. Maxwell theoretically predicted and then proved the existence of electromagnetic waves in the 1860s, and when Heinrich R. Hertz experimentally confirmed the actual existence of the electromagnetic wave in 1888.
In plant sites, there are various places such as those affording an unobstructed view like tank yards, and others surrounded by metal pipes and equipment obstructing the view (hereafter referred to "pipe jungles"), often seen in oil refinery and chemical on-site plants. The frequency band of radio waves used for field wireless communication is 2.4 GHz, which has high straightness and its ability to go around things can hardly be expected.
The FieldMate versatile device management wizard is PC software mainly used for configuring and adjusting field devices. Under the concept of "one tool for all," Yokogawa has been enhancing this software to support a wide range of field devices and field communication protocols.
In recent years, expectations for control systems using wireless communications have been increasing in the process control market. This is because these systems do not require power and communication wiring for field instruments, enabling reduced initial and maintenance costs, and easy installation.
기술 및 솔루션, 요꼬가와에 대한 자세한 정보를 찾고 계십니까?견적 및 기술문의