Percent Concentration Control

Introduction

There are numerous industrial applications where measurements and/or control of a specific chemical strength of the process is critical for optimizing the production of the end product. These specific concentrations are obtained by mixing a full strength solution with water to achieve the desired percent concentration.

Concentration

The desired chemical concentration is achieved using a two stage mixing procedure. During the first stage, the flow ratio control unit on the missing tank is set to provide (x) gallon per minute of the full strength solution and (y) gallons per minute of water. These values are adjusted to produce a concentration value which is slightly weaker than the desired value. This ratio control must include alarm capabilities to indicate "low flow" conditions for both the full strength solution and the water in order to prevent wasted chemicals or hazardous situations.

At the second stage, a conductivity sensor and analyzer function as a "trim control". This combination adds small amounts of full-strength solution to the mixing tank to produce the exact concentration desired.

Percent Concentration Control Figure 1

For example, to produce a 4% caustic solution from a large bulk caustic supply at 50%, the flow ratio controller is adjusted to make a 3% solution and the conductivity information is used to add additional caustic to achieve the 4% concentration.

Conductivity is a very reliable index of the concentration for most acid and base (caustic) solutions. Figure 1 shows the correlation between conductivity and concentration for four common solutions.

For most solutions, there is a peak conductivity value. Before this peak value is reached, conductivity correlates positively with concentration; after the peak, it correlates negatively. So, if the concentration range passes through the peak for that chemical the conductivity value (except the peak value) represents two different concentration values. Therefore, it is mandatory that any application near the peak of a particular solution be carefully controlled.

Summary

Conductivity measurement is a reliable indicator of the concentration of most acid or base solutions. In determining the proper loop components for a particular application, the material of construction will be of primary concern. A chemical resistance chart should be consulted (see Table 1), or an application data sheet completed and sent to the factory in order to insure an installation that will be suited for the intended application.

Table 1

 

PVC

CPVC

PP

PVDF

Hydrochloric Acid (HCl) @36% A3 A4 A4 A5
Sulfuric Acid (H2SO4) @96% A3 A3 B1 A3
Nitric Acid (HNO3) @50% A3 A3 B1 A2
Hydrofluroic Acid (HF) @40% A2 A2 A3 A4
Sodium Hydroxide (NaOH) @50% A3 A4 A3 X
Sodium Hypochlorite (NaOCl) with 15% Cl2 A3 A5 A1 X
Hydrogen Peroxide (H2O2) @30% A3 A2 A2 A5

Product Recommendations

Percent Concentration Control Product RecommendationsTransmitter
2-wire conductivity measurement system ISC202
4-wire conductivity measurement system ISC450

Sensor/ Holder
ISC40FS/ISC40FF Insertion of Flow-thru assembly
ISC40PR Retractable assembly
ISC40G General Purpose Sensor
ISC40S Intrinsically Safe Sensor

Where are the Opportunities

You will find these applications in many industries. Demineralized water systems use caustic and acid solutions to regenerate the resin beds. The vegetable processing industry uses caustic solutions as a cleaning agent. Acid and caustic solutions are used in Clean-In-Place (CIP) systems to remove residue from process equipment without dismantling the systems. Solutions of acid and caustic are used to neutralize waste streams before discharge to municipal systems. Anywhere you find these acid and caustic solutions, you will find someone who is interested in their concentrations. Inductive Conductivity provides a reliable, maintenance free method to monitor, control, and transmit this value.

Note: For additional information or assistance on this application, please contact the Yokogawa Analytical Product Marketing.

 

Industries

  • Food & Beverage

    At Yokogawa, we understand that today’s food and beverage companies face unprecedented challenges in climate change, consumer demand, and increased global competitiveness. Overcoming these challenges will require innovative solutions that focus on key areas of production, asset management, and food safety and quality.

    See More
  • Power

    In the mid 1970s, Yokogawa entered the power business with the release of the EBS Electric Control System. Since then, Yokogawa has steadfastly continued with the development of our technologies and capabilities for providing the best services and solutions to our customers worldwide.

    Yokogawa has operated the global power solutions network to play a more active role in the dynamic global power market. This has allowed closer teamwork within Yokogawa, bringing together our global resources and industry know-how. Yokogawa's power industry experts work together to bring each customer the solution that best suits their sophisticated requirements.

    See More

Related Products & Solutions

  • Percent Concentration Sensors ISC40

    There are numerous industrial applications where measurements and/or control of a specific chemical strength of the process is critical for optimizing the production of the end product. These specific concentrations are obtained by mixing a full strength solution with water to achieve the desired percent concentration.  

    See More
  • Conductivity Analyzers

    Conductivity meters, analyzers and transmitters are used for continuous process measurement and monitoring of conductivity, resistivity, WIFI, demineralizer water, RO water, percent concentration, boiler blowdown and TDS.

    See More
  • Conductivity Sensors

    Conductivity sensors and electrodes are used to measure process conductivity, resistivity, WIFI, demineralizer water, RO water, percent concentration, boiler blowdown and TDS. Various installation options including retractable, flow thru, immersion, and direct insertion. Proper electrode/sensor selection is critical for optimal measurement results.

    See More

Top